Euphonix System 5 Setup Manual
  1. Manuals
  2. Brands
  3. Euphonix Manuals
  4. Music Mixer
  5. System 5
  6. Setup manual

Euphonix System 5 Setup Manual

Post and film
Hide thumbs Also See for System 5:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Operating Manual, Installation Manual
Euphonix System
Euphonix Inc.
220 Portage Ave.
Palo Alto, California 94306
Phone:
650-855-0400
Fax:
650-855-0410
Web:
http://www.euphonix.com
e-mail:
info@euphonix.com
System 5 Post and
Film Setup Guide
Document Revision: 1.2
Release Date: January 2006

Advertisement

Table of Contents
loading

Related Manuals for Euphonix System 5

Summary of Contents for Euphonix System 5

  • Page 1 Euphonix System System 5 Post and Film Setup Guide Document Revision: 1.2 Release Date: January 2006 Euphonix Inc. 220 Portage Ave. Palo Alto, California 94306 Phone: 650-855-0400 Fax: 650-855-0410 Web: http://www.euphonix.com e-mail: info@euphonix.com...
  • Page 2 System 5, S-5, PatchNet, eMix, EuCon, R-1, Audio Deck, Studio Hub are trademarks of Euphonix Inc. ©2006 Euphonix, Inc. All rights reserved worldwide. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form by any means without written permission of Euphonix, Inc.

  • Page 3: Table Of Contents

    Euphonix System 5 Post and Film Setup Guide Table of Contents CM403 Installation ..........................5 CM403 Module......................5 External Record Control ....................6 Film Panel Installation ....................7 Joystick Panel Installation .....................9 Blank Panel ........................10 Record Control Setup........................11 Solo Linking ..........................12 Physical Connection Between Systems ...............12 Network Settings......................13...

  • Page 5: Cm403 Installation

    Euphonix System 5 Post and Film Setup Guide CM403 Installation CM403 Module The CM403 uses the same form factor and architecture as a standard control module (CM401, 402, 408). A single Ethernet port connects the module to the system via the 100 BaseT EuCon switch.

  • Page 6: External Record Control

    Euphonix System 5 Post and Film Setup Guide ID selection Up to four CM403 modules can be installed in a System 5 console. Set the ID switches on the back panel of the module according to Table 1: Table 1 CM403 ID Switch Settings...

  • Page 7: Film Panel Installation

    Euphonix System 5 Post and Film Setup Guide Film Panel Installation NOTE: Each instruction pertains to the picture beneath its text. Connect the 5-V power cables (red) from the Film Panel to the header block on the bot- tom of the module. Be sure to maintain correct polarity (red/white stripe is negative).
  • Page 8 Connect the opposite end of the PC104 cable to the PC104 card on the SBC (Single Board Computer) mounted on the rear ventilation panel of the module. Secure the RF choke as shown above. Connect the Euphonix Ext cable (25-pin D-sub on the rear panel) to H103 on the upper board of the Film Panel.

  • Page 9: Joystick Panel Installation

    Euphonix System 5 Post and Film Setup Guide Connect the TFT backlight cable to the connector on the upper board of the film panel. Joystick Panel Installation Connect the 5-V power cables (red) from the Joystick to the header block on the bottom of the module.

  • Page 10: Blank Panel

    Euphonix System 5 Post and Film Setup Guide Blank Panel .480 X2 .285 .437 11.00 X2 1.150 .625 10.960 1.800 FREE SPACE 6.700 8.200 2.300 .500 .500 1.800 .875 11.960...

  • Page 11: Record Control Setup

    Euphonix System 5 Post and Film Setup Guide Record Control Setup Version 2.5 of eMix added record and track-arming functionality to the System 5 console. Version 3.0x (or higher) of the TT007 software is required. One record machine with up to 48 tracks is supported; additional record machines can be supported using third-party hardware.

  • Page 12: Solo Linking

    Euphonix System 5 Post and Film Setup Guide Solo Linking NOTE: Problems may occur if the Solo Linking service is running when eMix is in- stalled. To avoid this, open the MOConfig.exe application and click Stop to stop the service before installing newer software.

  • Page 13: Network Settings

    Euphonix System 5 Post and Film Setup Guide Network Settings The settings for the network identification and addressing are found in the Network Connections window. Open the Network Connections window by choosing Settings->Network Connections from the Start menu. Change the Computer Name In the Network Connections window, select Network Identification from the Advanced menu.
  • Page 14 Euphonix System 5 Post and Film Setup Guide Figure 4 Computer Name tab 1. Click the Change button at the bottom-right. A dialog appears requesting the new name. Type one the following names depending on the console being changed: Master -...
  • Page 15 Euphonix System 5 Post and Film Setup Guide Assign IP Address to Second Network Interface Card Two network connections are displayed in the Network Connections window. One is for your console’s modules and pilots (typically named EuCon) the other for the con- nection to your outside LAN.
  • Page 16 Euphonix System 5 Post and Film Setup Guide Figure 6 Internet Protocol (TCP/IP) Properties dialog 3. Click the Use The Following IP Address radio button and enter the IP address according to the following: Master - 10.0.0.1 Slave1 - 10.0.0.2 Slave2 - 10.0.0.3...
  • Page 17 Euphonix System 5 Post and Film Setup Guide Figure 7 Advanced tab of Studio LAN Properties dialog 6. Press OK to close the connection properties dialog.
  • Page 18 Euphonix System 5 Post and Film Setup Guide Configure DCOM Using Component Services Editor 1. After restarting the computer, open the Component Services Editor. 2. Click Start and select Run. The Run dialog appears. Type dcomcnfg and press Enter. The Component Services Editor appears.
  • Page 19 Euphonix System 5 Post and Film Setup Guide Figure 9 My Computer Properties-Default Properties tab 7. Make sure Enable Distributed COM on this computer is checked, Default Authentication Level is set to None, and Default Impersonation Level is set to Impersonate.
  • Page 20 Euphonix System 5 Post and Film Setup Guide Figure 10 My Computer Properties-COM Security tab The tab has Edit Limits and Edit Defaults buttons for Access Permissions and Launch & Activation Permissions. Each button opens a permissions setting di- alog.
  • Page 21 Euphonix System 5 Post and Film Setup Guide Figure 11 Launch Permissions dialog example 11. When finished, click Apply in the My Computer Properties dialog and the OK to close it. 12. Back in the Component Services Editor window, expand My Computer, then...
  • Page 22 Euphonix System 5 Post and Film Setup Guide Figure 12 Component Services-S5MultiServer...
  • Page 23 Euphonix System 5 Post and Film Setup Guide 13. Right-click on S5MultiServer, then choose Properties. The S5MultiServer Properties dialog opens. Figure 13 S5MultiServer Properties-General tab 14. In the General tab, make sure that Authentication Level is set to Default. 15. Click Apply.
  • Page 24 Euphonix System 5 Post and Film Setup Guide 16. Click the Location tab. Figure 14 Location Dialog - Run on this computer. 17. On the Master console (S5M -10.0.0.1), select Run application on this computer. Figure 15 Location Dialog - Run on another computer.
  • Page 25 Euphonix System 5 Post and Film Setup Guide Figure 16 Select Computer dialog Click the Advanced button (bottom left). The Select Computer dialog expands to the advanced search mode. d. Click Find Now at the mid-right of the dialog. All the computers available on the network appear.
  • Page 26 Euphonix System 5 Post and Film Setup Guide Figure 17 Select Computer-Advanced tab dialog Select S5M and then click OK to close the Advanced dialog. S5M should now appear in the Select Computer dialog. Click OK to close that dialog.
  • Page 27 Euphonix System 5 Post and Film Setup Guide Figure 18 S5MultiServer Properties-Security tab 21. Make sure all three Use Default radio buttons are selected. 22. Click Apply then OK to close the S5MultiServer Properties dialog.

  • Page 28: Setting Up Moconfig

    Euphonix System 5 Post and Film Setup Guide Setting up MOConfig 1. Open up a Windows Explorer window and locate the C:\emix directory. Double-click MOConfig.exe to display the following dialog: Figure 19 Multi-Operator Configuration Dialog 3. Click the Enable Multi Operator checkbox.

  • Page 29: Block Diagram

    Euphonix System 5 Post and Film Setup Guide Block Diagram Figure 20 Dual Operator System Block Diagram...

Table of Contents