Control Change - Roland Groovebox MC-307 Reference Manual

and calculating the checksum" (P. 206).
* This message is not received if the Rx.System Exclusive Switch Switch parameter is OFF.
Data Set 1 DT1
This message transmits the actual data, and is used when you wish to set the data of the
receiving device.
status data byte
F0H 41H, dev, 00H, 0BH, 12H, aaH, bbH, ccH, ddH, eeH, ... ffH, sum
Byte Remarks
F0H Exclusive status
41H ID number (Roland)
dev device ID (dev: 10H–1FH)
00H model ID (MC-307)
0BH model ID (MC-307)
12H command ID (DT1)
aaH address MSB
bbH address
ccH address
ddH address LSB
eeH data: The actual data to be transmitted. Multi-byte data is transmitted
in the order of the address.
: :
ffH data
sum checksum
F7H EOX (End Of Exclusive)
* For the address, size, and checksum, refer to "Examples of system exclusive messages
and calculating the checksum" (P. 206).
* Data whose size is greater than 128 bytes should be divided into packets of 128 bytes or
less and transmitted. Successive "Data Set 1" messages should have at least 20 ms of
time interval between them.
* This message is not received if the Rx.System Exclusive Switch parameter is OFF.
The only GS exclusive messages received by the MC-307 are Scale Tune settings (P. 116).
Data Set 1 DT1
status data byte
F0H 41H, dev, 42, 12H, aaH, bbH, ccH, ddH, ... eeH, sum
Byte Remarks
F0H Exclusive status
41H ID number (Roland)
dev device ID (dev: 10H–1FH)
42H model ID (GS)
12H command ID (DT1)
aaH address MSB
bbH address
ccH address LSB
ddH data: The actual data to be transmitted. Multi-byte data is transmitted
in the order of the address.
: :
eeH data
sum checksum
F7H EOX (End Of Exclusive)
* This message is not received if the Rx.System Exclusive Switch parameter is OFF.
In addition to conventional system exclusive messages, the MC-307 also uses special system
exclusive messages for operations which require realtime handling, such as knobs.
Data Set 1 DT1
status data byte
F0H 41H, dev, 3AH, 12H, aaH, bbH, ccH, ddH, sum
Byte Remarks
F0H Exclusive status
41H ID number (Roland)
dev device ID (dev: 10H–1FH)
3AH model ID (MC-307 Quick)
12H command ID (DT1)
aaH address (Status/Channel)
bbH address/Data H
ccH Data L
ddH Data E
sum
F7H
* For the address, size, and checksum, refer to "Examples of system exclusive messages
and calculating the checksum" (P. 206).
* Transmission of consecutive addresses is not possible.
* This message is not received if the Rx.System Exclusive Switch parameter is OFF.
status
F7H
2. Data transmission
(sound source section)
Channel Voice messages
Note Off
status
8nH
Note On
status
9nH
vv=Note On velocity:

Control Change

* By selecting a controller number that corresponds to the setting of the Control Pedal
Assign parameter, you can transmit any desired control change.
Bank Select (Controller number 0,32)
status
BnH
BnH
mm,ll=Bank number:
* This message is not transmitted if Tx Program Change Switch parameter or Tx Bank
Select Switch parameter is OFF.
* For the Bank Select that corresponds to each Patch, refer to section 1.
status
F7H
Modulation (Controller number 1)
status
BnH
Portamento Time (Controller number 5)
status
BnH
Volume (Controller number 7)
status
BnH
Panpot (Controller number 10)
status
BnH
Expression (Controller number 11)
status
BnH
General purpose Controller1, 3, 4 (Controller number 16, 18, 19)
status
BnH
status Hold 1 (Controller number 64)
F7H
status
BnH
Portamento (Controller number 65)
status
BnH
MIDI Implementation
checksum
EOX (End Of Exclusive)
2nd byte 3rd byte
kkH vvH
2nd byte 3rd byte
kkH vvH
01H - 7FH (1 - 127)
2nd byte 3rd byte
00H mmH
20H llH
00 00H - 7F 7FH (bank.1 - bank.16384)
2nd byte 3rd byte
01H vvH
2nd byte 3rd byte
05H vvH
2nd byte 3rd byte
07H vvH
2nd byte 3rd byte
0AH vvH
2nd byte 3rd byte
0BH vvH
2nd byte 3rd byte
10H,12H,13H vvH
2nd byte 3rd byte
40H xxH
2nd byte 3rd byte
41H xxH
197