Page 1
Driver Manual (Supplement to the FieldServer Instruction Manual) FS-8700-41 Simplex Time Recorder Company - 4100 Computer Port Protocol APPLICABILITY & EFFECTIVITY Effective for all systems manufactured after December 2009 A Sierra Monitor Company Driver Version: 1.08 Document Revision:...
Connection to a Simplex 4100U Panel ... 8 Data Array Parameters ... 9 Configuring the FieldServer as a Simplex Time Recorder Company - 4100 Computer Port Protocol Client ... 10 Client Side Connection Parameters ... 10 Client Side Node Parameters ... 11 Client Side Map Descriptor Parameters ...
Page 3
Appendix C.4.1. Digital Pseudo’s: ... 40 Appendix C.4.2. Analog Psuedos ... 45 FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldserver.com Tel: (408) 262 2299 Fax: (408) 262 2269 Toll Free: (888) 509 1970 email: support@fieldserver.com Table of Contents...
SIMPLEX TIME RECORDE R COMPANY - 4100 COMPUTER PORT PROTOCOL The Simplex Time Recorder Company - 4100 Computer Port Protocol driver allows the FieldServer to transfer data to and from devices over either RS-232 or RS-485 using Simplex Time Recorder Company - 4100 Computer Port Protocol.
The following are the Simplex, recommended connections to be used in cabling between the 4100 and the FieldServer device. For the computer device, the standard EIA signal description, and the 25 pin (DB25) and 9 pin (DB9) connector assignments are shown.
FieldServer Port B Front of 4100U Panel FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldserver.com Tel: (408) 262 2299 Fax: (408) 262 2269 Toll Free: (888) 509 1970 email: support@fieldserver.com FS-8717-07 Port A Pin 2 - White...
Simplex Time Recorder Company - 4100 Computer Port Protocol Server. The configuration file tells the FieldServer about its interfaces, and the routing of data required. In order to enable the FieldServer for Simplex Time Recorder Company - 4100 Computer Port Protocol communications, the driver independent FieldServer buffers need to be declared in the “Data Arrays”...
, 4100U , Sim4100 FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldserver.com Tel: (408) 262 2299 Fax: (408) 262 2269 Toll Free: (888) 509 1970 email: support@fieldserver.com Legal Values Up to 32 alphanumeric characters This parameter is IGNORED. Keywords used to define the card-sub-point (c-p-s) are described in Appendix A.1...
<Sub_Type> FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldserver.com Tel: (408) 262 2299 Fax: (408) 262 2269 Toll Free: (888) 509 1970 email: support@fieldserver.com Legal Values Up to 32 alphanumeric characters One of the Data Array names from Section 4 0 to (Data_Array_Length-1) as specified in “Data_Array”...
CONFIGURING THE FIELDSERVER AS A SIMPLEX TIME RE CORDER COMPANY - 4100 COMPUTER PORT PROTOCOL SERVER The driver contains some server side functionality which has been developed to meet FieldServer’s continuous quality assurance efforts. However, the server side functions are not documented or supported for customer use. If you have a strong requirement for this functionality then please contact the Sales and Marketing group of FieldServer.
Appendix A.1. How to use Data Arrays to map to/from Card-Point-Sub addresses Some commands derive a c-p-s address by inspecting a FieldServer Data Array. Others receive data from a device and modify the data in an array based on the c-p-s address. This section explains how to make the connection between an index into a Data Array and a c-p-s address.
Simpl ex Point Status Data For mat When a point status is obtained the FieldServer will write one byte of data to a Data Array. The byte will contain the follow ing information. Ensure that the function of the Data Array is not Bit..
Attribute States. FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldserver.com Tel: (408) 262 2299 Fax: (408) 262 2269 Toll Free: (888) 509 1970 email: support@fieldserver.com Legal Values Sim4100 Define a state word such as ‘Normal’ and associate a value using the ‘value’...
ClearAll Since an Xpoint message only reports when a c-p-s goes into a non-normal state, this function is provided as a means of synchronising FieldServer to the panel when everything is normal. The function is typically used in conjunction with pseudo-point(s) programmed into the panel. The underlying logic assumes that...
(Xpoint messages). The panel sends an Xpoint message each time a point’s status changes to a non-normal state. Using these Map Descriptors will ensure that the FieldServer is constantly updated with the latest panel status information. The Map Descriptor’s are pa ssive so they can be used in a joint strategy with the clist function (Appendix A.3.1) to keep track of a point’s status.
Supervisory 6th – ack Trouble Set the array element to 1 to initiate the command. The FieldServer clears the value on completion Appendix A.4.5. Acknowledge a specific poi nt One Map Descriptor is required for each c-p-s combination requiring specific acknowledgements. The driver checks the array location corresponding to the Map Descriptor.
The driver will load the array DA_SHOW starting at offset zero for up to 100 elements. The following table can be used to determine the values to expect for this response. FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldserver.com Tel: (408) 262 2299 Fax: (408) 262 2269 Toll Free: (888) 509 1970 email: support@fieldserver.com Page 25 of 48 , Rdbc...
Page 26
Locations marked with a 1 are updated when the driver analyses this response FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldserver.com Tel: (408) 262 2299 Fax: (408) 262 2269 Toll Free: (888) 509 1970 email: support@fieldserver.com Page 26 of 48 Note The value 10 represents the count of the number of attributes that were extracted from the response.
This way the FieldServer states will always be updated. Polling is slow and in a system with many points it may take several minutes to update status information for all points. Thus combining this method with the use of Xpoint Map Descriptors gives the best of both worlds.
Control the ability of ‘CLIST’ map descriptors to be used to store data from unsolicited messages. Refer also to Store_Unsolicited* Appendix A.6.2 FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldserver.com Tel: (408) 262 2299 Fax: (408) 262 2269 Toll Free: (888) 509 1970 email: support@fieldserver.com Page 29 of 48 Legal Values...
Card-Address format where the address value is larger than 255. In these applications it is necessary to convert the Card-Address format into c-p-s format before configuring the points in the FieldServer. The formula used to convert between the two formats is as follows: Card is the same for both formats.
If a card is moved from one hardware location to another, it maybe necessary to revector the port. FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldserver.com Tel: (408) 262 2299 Fax: (408) 262 2269 Toll Free: (888) 509 1970 email: support@fieldserver.com...
The Simplex Time Recorder Company - 4100 Computer Port Protocol only uses the standard 4100 address format of <Card>-<Point>-<Sub-point>. Symbolic addressing is not supported. The following table lists keywords which control the behavior of the FieldServer with respect to connection to a Simplex device and the permissible values determining the type of data being read/written.
Page 33
(value 01 indicates 2001). A 24 hour clock is assumed. FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldserver.com Tel: (408) 262 2299 Fax: (408) 262 2269 Toll Free: (888) 509 1970 email: support@fieldserver.com Function RDBC Specify c-p-s in the Map Descriptor.
Page 34
Generates a cold restart message. FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldserver.com Tel: (408) 262 2299 Fax: (408) 262 2269 Toll Free: (888) 509 1970 email: support@fieldserver.com When the element in the Data Array Page 34 of 48...
(%.2f) FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldserver.com Tel: (408) 262 2299 Fax: (408) 262 2269 Toll Free: (888) 509 1970 email: support@fieldserver.com Description c-p-s is being used to derive an array offset. The calculation requires division by the point &...
Page 36
Sim4100:#33. Error. Invalid Seq Number. FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldserver.com Tel: (408) 262 2299 Fax: (408) 262 2269 Toll Free: (888) 509 1970 email: support@fieldserver.com Description Message ‘b’ is printed when version 10 firmware is found in the panel.
Page 37
Sim4100:#60 Err. MapDesc=%s. No Node. FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldserver.com Tel: (408) 262 2299 Fax: (408) 262 2269 Toll Free: (888) 509 1970 email: support@fieldserver.com Description Message sequence number incorrect. Check Simplex User Manuals, and driver manuals.
The driver counts messages at the application layer.. This means that if you use RUINET to monitor the FieldServer and you view the Map Descriptor’s the byte count stats will always be zero.
NUMBER OF SYSTEM SUPERVISORIES NUMBER OF SYSTEM TROUBLES FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldserver.com Tel: (408) 262 2299 Fax: (408) 262 2269 Toll Free: (888) 509 1970 email: support@fieldserver.com TROUBLE 128-196-0 UTILITY 128-197-0 UTILITY 128-198-0...
Page 46
ALERT TONE/MSG AFTER MICROPHONE UNKEYED ANALOG 144-47-0 TOTAL AUDIO CHANNELS CHANNEL 1 ROUTING FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldserver.com Tel: (408) 262 2299 Fax: (408) 262 2269 Toll Free: (888) 509 1970 email: support@fieldserver.com ANALOG 144-3-0 ANALOG 144-4-0 ANALOG 144-5-0...
Page 47
ACTIVE MESSAGE NUMBER - VTG 2 ACTUAL CHIPSET PLUGGED INTO VTG 1 FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldserver.com Tel: (408) 262 2299 Fax: (408) 262 2269 Toll Free: (888) 509 1970 email: support@fieldserver.com ANALOG 144-50-0 ANALOG 144-51-0...
Page 48
SUPERVISION DELAY SETPOINT CHL2 A133 SUPERVISION NOT ACTIVE DELAY SETPOINT FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldserver.com Tel: (408) 262 2299 Fax: (408) 262 2269 Toll Free: (888) 509 1970 email: support@fieldserver.com ANALOG 144-97-0 COUNTER 144-98-0 COUNTER 144-99-0...