Table of Contents
Related Manuals for FieldServer FS-8700-124
Summary of Contents for FieldServer FS-8700-124
- Page 1 A Sierra Monitor Company Driver Manual (Supplement to the FieldServer Instruction Manual) FS-8700-124 TIC UPS APPLICABILITY & EFFECTIVITY Effective for all systems manufactured after May 1, 2001 Driver Version: 1.01 Document Revision: 0...
-
Page 2: Table Of Contents
Required 3 Party Configuration ... 4 HARDWARE CONNECTIONS... 5 3.1. Hardware Connection Tips / Hints ... 5 CONFIGURING THE FIELDSERVER AS A TIC UPS CLIENT ... 6 4.1. Data Arrays/Descriptors ... 6 4.2. Client Side Connection Descriptions ... 7 4.3. -
Page 3: Tic Ups Description
ProtoNode Driver Manual (FS-8700-124) rev 6.doc Manual Page 3 of 17 TIC UPS Description The serial TIC UPS driver allows the ProtoNode to transfer data to and from devices over RS- 232 using TIC UPS protocol. The ProtoNode can emulate a Client. -
Page 4: Driver Scope Of Supply
ProtoNode Driver Manual (FS-8700-124) rev 6.doc Manual Page 4 of 17 Driver Scope of Supply 2.1. Supplied by FieldServer Technologies for this driver FieldServer Technologies PART # FS-8917-02 FS-8917-03 FS-8700-124 2.2. Provided by the Supplier of 3 2.2.1. Required 3 Part # 2.2.2. -
Page 5: Hardware Connections
ProtoNode Driver Manual (FS-8700-124) rev 6.doc Manual Page 5 of 17 Hardware Connections The ProtoNode is connected to the UPS as shown in connection drawing. Configure the TIC UPS according to manufacturer’s instructions. 8917-03 WIRE LIST FUNCTION FROM RJ45-01 RJ45-04... -
Page 6: Configuring The Fieldserver As A Tic Ups Client
For a detailed discussion on FieldServer configuration, please refer to the FieldServer Configuration Manual. The information that follows describes how to expand upon the factory defaults provided in the configuration files included with the FieldServer (See “.csv” sample files provided with the FieldServer). -
Page 7: Client Side Connection Descriptions
ProtoNode Driver Manual (FS-8700-124) rev 6.doc Manual Page 7 of 17 4.2. Client Side Connection Descriptions Section Title Connections Column Title Specify which port the device Port is connected to the ProtoNode Protocol Specify protocol used Baud* Specify baud rate... -
Page 8: Client Side Map Descriptors
ProtoNode Driver Manual (FS-8700-124) rev 6.doc Manual Page 8 of 17 Example // Client Side Nodes Nodes Node_Name, Node_ID, PLC 1, 4.4. Client Side Map Descriptors 4.4.1. FieldServer Related Map Descriptor Parameters Column Title Map_Descriptor_Name Name of this Map Descriptor... -
Page 9: Map Descriptor Example
ProtoNode Driver Manual (FS-8700-124) rev 6.doc Manual 4.5. Map Descriptor Example. 4.5.1. Example 1 // Client Side Map Descriptors Map_Descriptors Map_Descriptor_Name, Data_Array_Name, DA_AI_01, For all commands except FAULT and ALARM, ensure that the Data_Array_Name points to an array of type float. -
Page 10: Appendix A. Commands Specific To Devices
ProtoNode Driver Manual (FS-8700-124) rev 6.doc Manual Page 10 of 17 Appendix A. Commands Specific to Devices Appendix A.1. Client Read commands The following commands are supported with the RDBC function. ProtoCessor 1991 Tarob Court Milpitas, California 95035 USA Web:www.protocessor.com... - Page 11 ProtoNode Driver Manual (FS-8700-124) rev 6.doc Manual Page 11 of 17 Command Description ALARM Alarm data Battery current BECR Battery estimated charge remaining BEMR Battery estimated minutes remaining Battery life remaining BPV1 Bypass voltage phase 1 BPV2 Bypass voltage phase 2...
-
Page 12: Appendix A.1.1. Fault Command
ProtoNode Driver Manual (FS-8700-124) rev 6.doc Manual Page 12 of 17 Appendix A.1.1. FAULT command: Stored in bits, make sure array’s length is 24 and its type is bits. Bit # Function Bit 23: Not used Bit 22: Bit 21:... -
Page 13: Appendix A.1.2. Alarm Command
ProtoNode Driver Manual (FS-8700-124) rev 6.doc Manual Page 13 of 17 Appendix A.1.2. ALARM command: Stored in bits, make sure array’s length is 24 and its type is bits. Bit # Description Bit 23: Not used Bit 22: Bit 21:... -
Page 14: Appendix A.1.4. Commands Supported By Different Models
ProtoNode Driver Manual (FS-8700-124) rev 6.doc Manual Page 14 of 17 Appendix A.1.4. Commands supported by Different Models 1600: 1800 ALARM ALARM BEMR BECR BEMR BPV1 BPV1 BPFREQ BRHT BPFREQ BRHT FAULT DCBV IFRQ FAULT IFRQ OFRQ OLP1 OFRQ OLP1... -
Page 15: Appendix A.2.1. Commands Supported By Different Models
ProtoNode Driver Manual (FS-8700-124) rev 6.doc Manual Page 15 of 17 Command BTEST Appendix A.2.1. Commands supported by different models. 1600: 1800 BTEST BTEST Please note that due to battery health, this point can only be tested as specified by TIC ProtoCessor 1991 Tarob Court Milpitas, California 95035 USA Web:www.protocessor.com... -
Page 16: Appendix B. Troubleshooting Tips
ProtoNode Driver Manual (FS-8700-124) rev 6.doc Manual Page 16 of 17 Appendix B. Troubleshooting Tips Appendix B.1. Connection Tips & Hints 1. What should the baud rate in my configuration file be set to? Consult the UPS manual for the default baud rate of your UPS. - Page 17 ProtoNode Driver Manual (FS-8700-124) rev 6.doc Manual Page 17 of 17 THIS PAGE INTENTIONALLY LEFT BLANK ProtoCessor 1991 Tarob Court Milpitas, California 95035 USA Web:www.protocessor.com Tel: 408.964.4433 Fax: 408.964.4425 Toll_Free: 800.317.8319 email: sales@protocessor.com...
Need help?
Do you have a question about the FS-8700-124 and is the answer not in the manual?
Questions and answers