Recording Using An Audio Timer (Deck I Only) - Pioneer CT-WM62R Operating Instructions Manual

CD-DECK SYNCHRO RECORDING (DECK I only)
If the tape ends while the CD is still playing:
The CD player returns to the beginning of the current selection
and enters pause mode. To resume recording, load another
tape and check the tape running indicator to make sure that
the tape is moving in the desired direction. If not, press the
playback (_ or _1) button to change the tape direction, then
immediately press the stop (11) button. When the proper
direction is selected, press the CD SYNCHRO button again. If
the CD SYNCHRO button is not pressed within one minute, the
CD player enters stop mode,
If the auto-reverse function operates while the CD player is
still playing:
The CD player returns to the beginning of the current selection
and enters pause mode. A lO-second blank space is automati-
cally created on the reverse side, then the CD player resumes
playback and the cassette deck resumes recording.
RELAY SYNCHRO RECORDING
2,3
56 4 11
__J
i
13 12 9 7
B
NOTE:
During Relay Synchro Recording, it is only possible to program
the playback order of one disc at a time.
1. Load a compact disc into the CD player.
2. Place the cassettes on the tray.
• Make sure the erasure prevention tabs are intact.
3. Press the OPEN/CLOSE button to close the tray.
4. Press the remote control unit's ALL REW button.
• Even if the tape has been set to playback, pressing the
fast-reverse (-4<) button twice will select the ALL
REWIND mode.
• Wait until the rewind operation is finished.
5. Press one of the CASSETTE NUMBER buttons to
load the cassette for recording.
6. Press the RELAY button to select relay mode.
7. Select the desired tape transport mode with the
REVERSE MODE button.
8. Select the desired type of Dolby noise reduction for
each cassette with the DOLBY NR buttons (see page
16).
9. Press the recording (o) button to enter recording
standby mode.
10. Press the play button of the CD player.
11. Adjust the recording level (see page 17).
12. Press the stop buttons of both the cassette deck
and the CD player.
• Unless both this cassette deck and the CD player are in
stop mode, synchro recordingcannot be performed.
13. Press the CD SYNCHRO button.
• The cassette deck begins recording and the CD player
starts playing about 10 secondslater.
When the compact disc finishes playing:
The CD player enters stop mode and the cassette deck loads
the next cassette, then enters recording standby mode.
Change the disc and press the play button of the CD player to
resume recording. If the CD player does not resume play
within one minute, the cassette deck enters stop mode.
When the CD player changes discs
(twin-tray or multi-play CD players):
The cassette deck loads the next cassette tape and then enters
recording standby mode. The CD player will change the disc,
and the cassette deck resumes recording when the CD player
begins playing the next disc. The cassette deck begins rec-
ording, and the CD player begins playback about 10 seconds
later.
If the tape ends while the CD is still playing:
The CD player plays the rest of the compact disc. The cassette
deck waits until the CD finishes playing, then loads the next
tape and enters recording standby mode.
NOTE:
If the erasure prevention tabs have been removed from any of
the loaded cassettes, the cassette deck will stop when it
encounters the removed tab (i.e., when it attempts to begin
recording on the protected side). Relay synchro recording is
terminated.
RECORDINGUSING AN AUDIO TIMER (DECK I only)
I
4 1,2 3
8
r-"_-r--r'_ r-'l
I .....
I u] a nl 1 -PII,
5 9 6
When this cassette deck is connected to an audio timer, two
timer modes can be selected. l]mer Relay Recording or Timer
Playback.
TIMER RELAY RECORDING
Unattended recording from tuner, etc.)
At the selected time, relay recording of all tapes on the tray
begins, starting with the tape in the lowest numbered slot.
1. Place the cassettes on the tray.
• Make sure that the erasure prevention tabs are intact.
2. Press the OPEN/CLOSE button to close the tray.
3. Press one of the CASSETTE NUMBER buttons to
load the cassette for recording.
For relay recording, press the CASSETTE NUMBER button
to load the tape you want to record first.
23
<RRB1134>
En