ProScan PS27123 Owner's Manual page 11

@
@
@
@
1@
INPUT BUFrON lets you quickly
view signals from the
INPUTjacks. Pressing this button switches the TV from
its current channel directly to channel 90, then channel
91, then channel 92. Channel 90 lets you see the signals
coming from a device that is connected to the S-VIDEO
connector. Channel 91 accesses the INPUT1 jacks, and
channel 92 accesses the iNPUT2 jacks.
CLEAR Burr0N
Pressing CLEARquickly clears the screen of all on-screen
display messages (except mute and parental control). It
is also used to cancel the Commercial Skip count-down
clock and to erase channel labels.
MENUopROGBU'Fr0N
Press MENU-PROG(called MENUin this Owner's Manual)
repeatedly until the menu you want to display is selected,
then press + or -. Next press MENU repeatedly to select
the function you want to adjust and then press + or - to
adjust the setting. Details about using each function
begin on page 11.
[CC] CLOSED C APTIONING B U'FrON
Once you have set the capt!oni.ng mode in the Setup
menu, press
[CCI to
turn captioning on and off while
watching TV.
BURON turns on TV and puts remote in "TV Mode"
:so that the other remote buttons will control the TV.
Also displays time (if clock has been set) and channel
number on the TV screen.
,@
SKIPBUTrON " " • " " -
Use this button when you want to scan other channels
during a commercial break. When a program break
occurs, press SKIPonce before changing channels. The
TV will count down 30 seconds on the screen and then
automatically switch back to the original channel you
were watching.
Press SKiPtwice if you Want the TV to count down 60
seconds. Each additional press will add another 30
seconds to the count-down time (up to five minutes) and
then each additional press will add another 60 seconds to
the countdown time (up to 60 minutes ) .
To cancel, •press CLEAR. T he countdown clock will
disappear from the screen, and the TV will stay tuned to
the channel it was. on when you pressed CLEAR.
PREVCH (PREVIOUSCHANNEL)BUTTON
Pressing
the PREV CHbutton causes the TV to change back
to the last-tuned channel.
To Operate, select the first•channel you want to watch.
Then select the other channel by pressing two number
buttons. The TV will now change b'ack and forth
betwecn the two channcls each time you press thc PREY
CR button.
ANTENNA BUII'0N
Because your TV has two different antenna inputs on the
back (labeled ANTA and ANT a) you can connect more than
one antenna or signal source. Press the ANTENNA button to
switch from one input to the other.
The color of the channel number on the screen indicates
which antenna input you are watching. The channel
numbers are blue for ANTA and yellow for ANTB. If the
channel numbers are blue, you are watching whatever is
connected to the ANTA input on the back of the TV. If the
channel numbers are yellow, you are watching whatever
is connected to the ANTB input on the back of the TV.
Details are on page 15.
RESETBuTroN
Resets the TV back to its original factory settings.
(_ MOVE + -
AND BUTI'0NS
Use the MOVE+ and -buttons (called + and - inthis
Owner's Manual) to enter or adjust functions after you
have pressed the MENUbutton.
Important Note: Most buttons on ihe remote control Will not
control the TV unless the remote is in the "TV Mode"..If another •
component button (such as VCR1) is pressed, the remote will no .
longer be in the "TV Mode".. To get back into the "'IV Mode",
simply press the button labeled w. The remote will go back into the
"TV Mode" and will control the TV again.
o
¢3
a