Related Manuals for Nokia NetMonitor
Summary of Contents for Nokia NetMonitor
- Page 1 Nokia NetMonitor Manual Version 0.5 Base document : Flipo ( flipo@gyral.com PDF + Enhancements to base document : nobbi ( nobbi@nobbi.com Graphics : nobbi...
- Page 2 The goal right now is to make an accessible manual, that will get better over the time. Please contribute with all the info that you find relevant. Information Sources : [ 1 ] Netmonitor description (RD843.txt) from Nokia Mobile Phones [ 2 ] Marcin Wiaceks homepage ( http://marcin-wiacek.topnet.pl...
- Page 3 Display 1 – Serving cell info ++++++++++++++ ############## +abbb ccc ddd+ #CH RxL TxPwr# + e ff g mmmm+ #TS TA RQ RLT# + nnn ppp+ # C1 C2 # oooo ++++++++++++++ ############## H, if carrier numbers are scrolled when hopping is on. Otherwise ' '. When mobile is on a TCH : DCH carrier number in decimal.
- Page 4 Display 2 – More info about serving cell ++++++++++++++ ############## + aa b c Bdd + #PM RAR Ro BC# + ee f #RelR QLF + ggg hh iii + #CRO TO PenT # + H=j mm nn #H MAIO HSN ++++++++++++++ ############## paging mode...
- Page 5 Display 4 & 5 – 3 to 8 neighbour cell ++++++++++++++ ############## +aaabbbcccddd+ #3CH C1 rx C2# +aaabbbcccddd+ #4CH C1 rx C2# +aaabbbcccddd+ #5CH C1 rx C2# ef gh ij 3N 4N 5N ++++++++++++++ ############## 1. row: 3./6. neighbour information 2.
- Page 6 Display 7 – System information bits for serving cell ++++++++++++++ ############## +E A H C I BR+ #Serving Cell# +a b c d e fg+ #System Info # +ECSC 2Ter MB+ #Bits ++++++++++++++ ############## 1 is shown if emergency calls are supported 1 is shown if attach-detach-procedure is allowed 1 is shown if half rate channels are supported 1 is shown if C2 values are broadcasted...
- Page 7 Display 10 – Paging Repeat Period, TMSI, Location Update Timer, AFC and AGC ++++++++++++++ ############## +TMSIaaaaaaaa+ #TMSI(hex) +T321:bbb/ccc+ #T3212ctr/tim# +PRP:d ee ff+ #PaRP DSF AGC# + ggggg hhh + ++++++++++++++ ############## aaaaaaaa last assigned TMSI value in hex format Current value of T3212 counter (range is 000 - 'ccc', where 1 means 6 min time.
- Page 8 Display 13 – Uplink DTX switching display ************** ############## *aaaaaaaaaa #DTXMode *DTX(DEF):bbb* #DefaulDTXSta# *DTX(BS) :ccc* #DTXValFromBS# ************** ############## With this display it is possible to change wether MS to use DTX or not. This display must be activated from MENU to change DTX state. When MENU is not active and the user is scrolling field test displays with NEXT and PREVIOUS, the DTX state will not be changed.
- Page 9 Display 17 – Switch BTS_Test Status ************** ************** ############## #Use menu to # BTS TEST BTS TEST #toggle BTS #test ON/OFF # ************** ************** ############## This display is used to toggle the BTS_TEST flag in EEPROM. If BTS_TEST is set then each time the mobile sends a search list it uses only the carrier number stored on SIM phonebook location 33.
- Page 10 Display 20 – Charging state ************** ############## * aaa bbbbb * #BatVol ChMod# * Tccc dddd * #Btemp ChTime# * Ceee Wfff * #ChrgVol Pwm # * gggg hhhh * # Btyp BFDC # ************** ############## Battery voltage in decimal, range is 0.00 - 9.99 V, decimal point is not shown; e.g.
- Page 11 Display 21 – Constant voltage charging display ************** ############## * aaaa bbbb * #MTDif MPDif # * cccc dddd * #BupV BDownV# * eeee ffff * #AverV SumMF # ************** ############## aaaa Difference between measured voltage and goal voltage, decimal point is not shown.
- Page 12 Display 23 – Battery and phone state monitor ************** ############## * aaaa bbbb * #TxOn TxOff# * cccc dddd * #ChCur Stdby# *eee fff gggg* #Age CAP Curr# *hhh iiiijjjj* #Tmp CmAhTarg# ************** ############## aaaa TXon voltage (expected voltage with transmitter switched on), decimal point not shown (a.aaa mV) bbbb TXoff voltage (expected voltage with transmitter switc hed off), decimal point...
- Page 13 Display 34 – FBUS display ************** ############## *aabbccdd #CM LD LM NM # *eeefff - ggg* #PEC FEC OEC # *hhh iii jjj * #ACC RXS TXS # *k-- #Mod ************** ############## current fbus media in hex last sender dev in hex last sender media in hex Next media to be connected.
- Page 14 Display 39 – Information about reasons for call clearing ++++++++++++++ ############## + CC: aaaa #CC CauseValu# + MM: bbbb #MM CauseValu# + RR: cccc #RR CauseValu# ++++++++++++++ ############## aaaa, bbbb, cccc cause code value, see section 10.5/GSM 04.08, '*' is shown if the cause code is made up by the respective layer in MS unassigned (unallocated) number no route to destination...
- Page 15 Display 40 – Reset handover counters ************** ############## RESET Use menu HANDOVER to reset COUNTERS handover counters ************** ############## With this display all counters of the handover di splays can be reset. Display 41 (in singleband phones) – Handover display ++++++++++++++ ############## +HandOOK: aaa+...
- Page 16 Display 42 (only in dualband phones) – Handover display, INTRA CELL ++++++++++++++ ############## + aaaa bbbb + #G>G IntraD>D# + cccc dddd + #G>D D>G# +eeefffggghhh+ #IntraHoFail # +iiijjjkkklll+ # BackToPrev # ++++++++++++++ ############## counter of successful INTRACELL handovers (max 9999) from GSM900 to GSM900 counter of successful INTRACELL handovers (max 9999) from GSM1800 to GSM1800 counter of successful INTRACELL handovers (max 9999) from GSM900...
- Page 17 Display 45 – Toggle transmitter functionality ************** *TRANSMITTER * XXXXXXXX XXXXXXXX ENABLED or DISABLED ************** This display has no effect in 7110 phone, irrespective of the displayed status the transmitter is always switched on. When selected, this display disables transmitter functionality if enabled and vice versa. New setting is valid until next power off or until new execute of this display.
- Page 18 Display 55 – Block display 2 ++++++++++++++ ############## +aa bb aa bb+ #ResF9 ResF10# +aa bb aa bb+ #ResF11ResF12# +aa bb aa bb+ #ResF13ResF14# +aa bb aa bb+ #ResF15ResF16# ++++++++++++++ ############## 1. row: Block set 9, block set 10 2. row: Block set 11, block set 12 3.
- Page 19 Display 60 – Reset counters to zero ************** ############## * FIELD TEST * #Use menu to # DISPLAY #reset field # COUNTERS #test display# RESET # counters ************** ############# # With this display all counters of the field test display can be reset (i.e. all counters in 40 and 60 series).
- Page 20 Display 62 – Neighbour measurement counter display ++++++++++++++ ############## + PSW :aaaa + #NeghbrPSWCtr# + SYNCR:bbbb + #SyncMeasCntr# + BCCH :cccc + #BCCHMeasAtmp# + BCCHE:dddd + #BCCHExtMeAtm# ++++++++++++++ ############## aaaa counter for neighbour PSW measurement attempts bbbb counter for neighbour synchronization measurement attempts cccc counter for neighbour BCCH measurement attempts dddd...
- Page 21 Display 65 - SMS attempts counters ++++++++++++++ ############## + aa bbb ccc + #SFai MO MOOK# + dd eee fff + #RFai MT MTOK# + gggg #Sched Msgs #SMS counters# ++++++++++++++ ############## Reason of last sending failure Count of all MO short message attempts Count of succeeded MO short message attempts Reason of last receiving failure Count of all MT short message attempts...
- Page 22 Display 70 - Temporary counters of DSP ++++++++++++++ ############## + aaaa bbbb # Temporary + cccc dddd #DSP counters# + eeee ffff #(R DSP2FTD) # + gggg hhhh ++++++++++++++ ############## aaaa Contents of API memory location r_dsp2ftd+0 in hex format bbbb Contents of API memory location r_dsp2ftd+1 in hex format cccc...
- Page 23 Display 74 - DSP audio enhancements 1 (DRC) ++++++++++++++ Example: ++++++++++++++ ############## #DSigL USigL # NseLvl# # DTbl UTbl # ++++++++++++++ ++++++++++++++ ############## Downlink signal level in dB, calculated using DRC level measuring block. Decimal point and sign is not shown, ie. -10.5 is show 105. Uplink signal level in dB, calculated using DRC level measuring block.
- Page 24 Display 77 - Microphone (= uplink) audio display ++++++++++++++ Example: ++++++++++++++ ############## + Paaa Abbb + + P303 A225 + #MicPeak MAve# + Cccc CAddd + + C023 CA003 + #CutOff COAve# ++++++++++++++ ++++++++++++++ ####### ####### Peak value of uplink audio signal during last frame in dB decimal point and sign is not shown, ie.
- Page 25 Display 79 - Audio equalizer display ++++++++++++++ Example: ++++++++++++++ ############## +aaaaa bbbbb + +12345 54321 + #MiCutB MiCTA# +ccccc ddddd + + 2353 46187 + #EpCutB EPCTA# +-ee.e -ff.f + +-46.5 -27.4 + #MicLev EarLv# ++++++++++++++ ++++++++++++++ ############## aaaaa Saturated samples before microphone equalizer in decimal 16 bit unsigned integer format.
- Page 26 Display 80 - Reset and restart timers ************** ############## Use menu TIMERS to reset RESET # field test # timers ************** ############## With this display all timers of display 82 can be reset. These timers will be automatically reset after the battery has been fullycharged and the charger is disconnected.
- Page 27 Display 83 - Control of task information displays ************** * SHOW TASK * XXXXXXXXX XXXXXXXXX is "STACKS", "MSG BUFS" or "FAST BUFS" ************** Shows what information about tasks is currently shown in displays 84 - 87. To select the type of information select this display via menu. Type is changed in order STACKS ->...
- Page 28 Display 88 - Information of the current MCU and DSP software versions ************** ############## *aaaaa bbbbbb* #MCUSW *Date cccccc* #MCUSW_Date *ChkSum dddd * #MCU_Checksum# *eeeeeeeeeeee* #DSP_Version # ************** ############## aaaaa version number of MCU SW bbbbbb PPM version cccccc date of version.c (e.g. 990102 means 02. January 1999 ) dddd MCU SW checksum eeeeeeeeeeee...
- Page 29 Monitor from Nobbi (http://www.nobbi.com/monitor/ use PCLocals from Nokia Display 242 – No output - Disable R&D field test displays This Display has no output, but does the following when directly selected: Disables R&D filed test displays, but leaves the netmonitor displays (1..19) active, so you...