Table of Contents
Advertisement
To remove belt cover
1.
Remove the two (2) screws (A) securing belt cover (B) to frame
(C).
2.
Remove belt cover.
Replace belt cover by installing cover and screws and tighten se-
curely.
®
Entfemen
der riemenabdeckung
1.
Entfernen Sie die zwei (2) Schrauben (A), mit denen die Riemena-
beckung (B) am Rahmen (C) befestigt ist.
2.
Entfernen Sie die Riemenabdeckung.
•
Befestigen Sie die Riemenabdeckung
erneut, indem Sie die Ab-
deckung und die Schrauben wieder anbringen und die Schrauben
fest anziehen.
Pour enlever
le couvercle
de la courroie
_
Her verwijderen
van de riemhuls
1.
Enlevez les deux (2) vis (A) en fixant le couvercle de _
1.
Verwijder de twee (2) schroeven (A) die de riemhuts (B)
la courroie (B) au ch&ssis (C).
aan het frame (C) bevestigen.
2.
Entevez le couvercle de la courroie.
2.
Verwijder de riemhuts.
•
Remptacez le couvercle de la courroie en installant le
•
Zet de riemhuts weer terug door de huls en de schroeven
couvercle et serrez solidement,
terug te ptaatsen en draai stevig aan.
@
Desmontar
e, cubre correas
@
Rimuovere
iJcoperchio
de,,a cinghia
1.
Desmontar los dos (2) tornillos (A) que sujetan et cubre
1.
Togliere le due (2) viti (A) che fissano il coperchio della
correas (B) a la carcasa (C).
cinghia (B) all'intelaiatura
(C).
2.
Desmontar et cubre correas.
2.
Togliere it coperchio della cinghia.
•
Sustituir et cubre correas cotocando la cubierta y los
•
Rimettere coperchio e viti, stringendo bene.
tornillos y apretando firmemente.
@
To replace
belts
The auger and traction drive belts are not adjustable. If the belts are damaged
or begin to slip from wear, they should be replaced. It is recommended
that
the belt(s) be replaced by a qualified service center.
NOTE: It is recommended
that both the auger and traction drive belt be
replaced at the same time.
The V-belts on your snow thrower are of special construction
and should
be replaced by original equipment manufacturer
(OEM) belts available from
your nearest dealer. Using other than OEM belts can cause personal injury
or damage to the snow thrower.
A
WARNING:
Belt replacement
requires
separation
of the snow
thrower. While separating
the auger housing
(1) from the frame as-
sembly (2), it is important that an assistant
stand in the operating
position and hold the snow thrower
handles
(3). Serious personal
injury and/or damage to the unit could occur
if the snow thrower
should
fall during the belt changing
process.
1.
REMOVE GASOLINE FROM FUEL TANK - Drain gasoline from fuel
tank into a suitable container, outdoors, away from fire or flame. Wipe
up any spilled gasoline.
2.
REMOVE DISCHARGE CHUTE- Loosen lock nut securing chute rotator
head to mounting bracket only enough to allow chute rotator head to be
raised and discharge chute to be removed from snow thrower.
3.
REMOVE BELT COVER - See "TO REMOVE BELT COVER" in this
section of this manual.
4.
REMOVE ENGINE PULLEY (A) - Remove bolt (B), flat washer (D) se-
curing pulley to engine crankshaft.
Remove outside (auger) pulley (A)
only from crankshaft.
5.
SEPARATE SNOW THROWER
- With your assistant standing in the
operating position holding the handles, remove the two bolts (F) holding
auger housing (1) and frame (2) together.
_lb
ARNING: As the last bolt is removed,
have your assistant
care-
fully lower the handles down to the ground.
6.
REMOVE HAIRPIN FROM CLUTCH ROD and remove clutch rod from
swing plate. Tip swing plate forward.
7.
REMOVE AUGER BELT (H) from around pulley (E).
8.
RELIEVE TENSION ON TRACTION DRIVE BELT IDLER (J) and remove
traction drive belt (K) from around pulleys.
46
Advertisement
Table of Contents
