Clearing Configurations; Clearing Function Sets (Clear); Clearing A Learned Function (Erase) - Yamaha DSP-Z11 Owner's Manual

6
Press GSETUP again to exit from the setup mode.
Note
"ERROR" appears in the display window (B) if you press more than one button
simultaneously.

Clearing configurations

You can clear all changes made in each function set, such as learned
functions, macros, renamed control area names and setup remote
control ID.

■ Clearing function sets (CLEAR)

1
Press GSETUP on the remote control using a
ballpoint pen or similar object.
"SETUP" appears in the display window (4).
2
Press 9k / n repeatedly to select "CLEAR" and then
press 9ENTER.
The remote control enters the clear mode. "CLEAR" and
"L:the three-letter name of the selected control area" (for
example, "L:DVD") appears in the display window (4)
alternately.
CLEAR
3
Press 9k / n repeatedly to select the desired clear
mode.
Clear mode
L:DVD (etc.) (L:Three-digit name of the selected control area) Clears all
learned functions the respective control area. You can
change the control area to be cleared by pressing the desired
input selector button or
repeatedly.
L:AMP Sets all learned functions for controlling the amplifier
functions to the initial factory settings. Set the operation
mode selector to FAMP to select this clear mode.
L:TV Clears all learned functions for TV control area. Set the
operation mode selector to FTV to select this clear mode.
L:ALL Clears all learned functions.
M:DVD (etc.) (M:Name of the selected macro button) Clears the macro
programmed for the selected macro button (see page 108).
The assigned macro to the selected macro button reverts to
the initial factory macro. Press the desired macro button if
you want to change the macro button you want to clear the
programmed functions of.
M:ALL Clears all programmed macros. The assigned macro to the
selected macro button reverts to the initial factory macro.
RNAME Set all the name of the control areas to the default settings.
FCTRY Set all settings of the remote control to the initial factory
settings.
4
Press and hold 9ENTER for about 3 seconds.
When the clearing is successful, "OK" appears in the display
window (4).
L:DVD
Descriptions
(3) or 5SELECT l / h
Notes
• "NG" appears in the display window (4) if clearing was unsuccessful.
• "ERROR" appears in the display window (4) if you press a button not indicated in
the respective step, or if you press more than one button simultaneously.
5
Press GSETUP again to exit from the setup mode.

■ Clearing a learned function (ERASE)

1
Press GSETUP using a ballpoint pen or similar
object.
"SETUP" appears in the display window (4).
2
Press 9k / n repeatedly to select "ERASE" and then
press 9ENTER.
The remote control enters the learning mode. "ERASE" and
the name of the currently selected control area appears in the
display window (4) alternately.
ERASE
Set the operation mode selector to F SOURCE and
3
then press an input selector button or
"ERASE" and the name of the selected control area appears in
the display window (4) alternately.
y
• You can also select the desired control area by pressing 5SELECT l / h
repeatedly.
• If you want to erase the function learned in the AMP or TV control area, set the
operation mode selector to FAMP or FTV.
4
Press 9ENTER.
"E-KEY" appears in the display window (4).
5
Press and hold the button you want to clear for about
3 seconds.
If clearing is successful, "ERASE" and "OK" appears in the
display window (4).
ERASE
y
• If you continuously want to clear another function, repeat step 3.
• Once you clear a learned function, the button reverts to the factory setting (or to
the manufacturer setting if you have set remote control codes).
6
Press GSETUP again to exit from the setup mode.
Notes
• "NG" appears in the display window (4) on the remote control if clearing was
unsuccessful.
• "ERROR" appears in the display window (4) if you press more than one button
simultaneously.
Remote control features
DVD
(3).
OK
109
En