Programming Codes From Other Remote Controls (Learn) - Yamaha DSP-Z11 Owner's Manual

1
Press GSETUP on the remote control using a
ballpoint pen or similar object.
The remote control enters the setup menu. "SETUP" appears in
the display window (4) on the remote control.
2
Press 9k / n repeatedly to select "P-SET" and then
press 9ENTER.
The remote control enters the preset mode. "P-SET" and name
of the currently selected control area appears in the display
window (4) alternately.
3
Set the operation mode selector to GSOURCE and
then press an input selector button or
5SELECT l / h repeatedly to select the control
area you want to customize.
"P-SET" and name of the selected control area appears in the
display window (4) alternately.
P-SET
y
If you want to select "TV", set the operation mode selector to FTV.
4
Press 9ENTER.
The five-digit code set for the selected control area appears in
the display window (4).
04306
Note
"00000" appears in the display window (4) if no code has been set.
5
Press the numeric buttons (B) to enter the
five-digit remote control code for the component you
want to use.
For a complete list of available remote control codes, refer to
"List of remote control codes" at the end of this manual.
y
You can also enter the desired number by pressing 9 k / n / l / h repeatedly.
6
Press 9ENTER to set the number.
"OK" appears in the display window (4) if setting was
successful.
"NG" appears in the display window (4) if the setting was
unsuccessful. In this case, start over from step 3.
y
If you continuously want to set up another code for another control area, repeat
steps 3 through 6.
Press G SETUP again to exit from the setup mode.
7
Press A p or 2AV POWER to confirm whether you
8
can control your component using the remote
control.
y
If operation is not possible and the manufacturer of your component has more than one
code, try each of them until you find the correct one.
Notes
• "ERROR" appears in the display window (4) on the remote control if you press a
button not indicated in the respective step, or when you press more than one button
simultaneously.
• The supplied remote control does not contain all possible codes for commercially
available audio and video components (including Yamaha components). If operation
is not possible with any of the remote control codes, program the new remote control
function using the learning feature (see "Programming codes from other remote
controls (LEARN)" on page 105) or use the remote control supplied with the
component.
• Functions programmed using the learning mode take priority over remote control
code functions.
• If you set "00012" as the remote control code of the selected control area, you can
operate the currently selected internal source (DOCK, or NET/USB).
Programming codes from other remote
(3) or
controls (LEARN)
You can program remote control codes from other remote controls.
Use the learning feature if you want to program functions not
included in the basic operations covered by the remote control
codes, or an appropriate remote control code is not available. You
can program the function of other remote control to the buttons in
DVD
the highlighted areas in the following illustration. The buttons can
be programmed independently for each control area.
POWER
TV
MULTI
BD
HD DVD
CBL
SAT
TUNER
SELECT
Notes
• The remote control transmits infrared rays. If the other remote control also uses
infrared rays, this remote control can learn most of its functions. However, you may
not be able to program some special signals or extremely long transmissions. Refer to
the operating instructions for the other remote control.
• You cannot program the desired remote control code even if you select the buttons in
the highlighted area in the above illustration depending on the selected control area
and the assigned library.
1
Set the operation mode selector to FSOURCE and
then press an input selector button or
the desired control area.
The name of the control area you want to customize appears in
the display window (4) on the remote control.
y
• You can also select the desired control area by pressing 5SELECT l / h
repeatedly.
• If you want to select "TV", set the operation mode selector to FTV.
Note
Make sure that the operation mode selector is set to F SOURCE or FTV. When
you set the operation mode selector to FAMP and program a remote control
codes from other remote controls, the programmed key cannot operate the
amplifier function of this unit.
2
Press GSETUP using a ballpoint pen or similar
object.
"SETUP" appears in the display window (4).
POWER STANDBY POWER
AV
MD
V-AUX PHONO
TAPE
DVD CD CD-R
DTV DVR VCR
NET
DOCK
USB
AMP Set to
TV
SOURCE
SOURCE
MACRO
SETUP ID
Remote control features
SYSTEM MEMORY
1 2 3 4
LEVEL SRCH MODE VOLUME
PRESET/CH
TITLE MENU
BAND
A-E
ENTER
RETURN DISPLAY
MEMORY
MUTE
PC/MCX
REC
NET RADIO USB
CLASSICAL 1 CLASSICAL 2 LIVE/CLUB ENTERTAIN
1 2 3 4
MOVIE STEREO ENHANCER SUR. DECODE
5 6 7 8
THX STRAIGHT PURE DIRECT EXTD SUR.
9 0 10 ENT
PARTY SLEEP HDMI OUT AUDIO SEL
MUTE AUDIO
TV VOL TV CH TV
3D DSP
INPUT
(3) to select
105
En