Yamaha DSP-Z11 Owner's Manual page 88

Graphical user interface (GUI) menu
2
Press 9 h to access the settings window.
PEQ Data Copy
PEQ Select
Front L
Front R
Center
3
Press 9 k / n / l / h to select "PARAM" and then
press 9 ENTER to select a parameter from "Band"
(band), "Freq." (frequency) or "Q" (Q factor).
y
You can adjust "Gain" (gain) with any parameter.
Press 9 n to select "EDIT" and press 9 ENTER to
4
access the edit window.
For more information on the parametric equalizer and each
parameter, see page 131.
PEQ Data Copy
PEQ Select
Front L
Front R
Center
The parameter selected in "PARAM" is highlighted.
• Press 9 l / h to adjust the parameter.
• Press 9 k / n to adjust the "Gain".
• Press 9 ENTER to exit the edit window.
y
• When you select "Band" in step 3, you can use this menu as a graphic
equalizer.
• "Band #4", "Band #5", "Band #6", and "Band #7" can adjust the frequencies
above of 500 Hz.
• When you select "Subwoofer L" or "Subwoofer R" in step 1 and "Band" in
step 3, you can adjust "Band #1", "Band #2", and "Band #3" only. In this case,
"Band #1", "Band #2", and "Band #3" can adjust the frequencies below of 250
Hz.
5
Repeat steps 3 and 4 until you are satisfied with the
results.
y
If you want to reset all "Parametric EQ" parameter settings for the selected
speaker, select "RESET" and press 9ENTER.
Select "EXIT" and press 9 ENTER to exit from the
6
settings window.
■ Tone Control (Tone control)
Use this feature to adjust the balance of bass and treble output to
your speakers or headphones.
Note
Tone Control is not effective when:
– the Pure Direct mode (see page 61) is selected.
– one of the THX Surround mode is selected (see page 73).
– MULTI CH is selected as the input source.
88
En
PARAM RESET
EDIT EXIT
Band/Gain
Band #1
Gain 0.0dB
Freq. 62.5Hz
Q 1.000
Control (Tone control)
Choice
Speaker Adjust the bass/treble balance of your speakers.
Headphone Adjust the bass/treble balance of your headphones.
y
"Speaker" and "Headphone" adjustments are stored independently. The adjustments for
"Speaker" affects the front left/right, center, presence left/right speaker channels and
Subwoofer channel.
Bass (Bass control)
Use this feature to adjust low-frequencies output to your speakers or
headphones.
Choices: 125 Hz, 350 Hz, 500 Hz
Control range: – 6.0 dB to +6.0 dB
Initial setting: 0.0 dB
Control
Bass
Treble
Auto Bypass
Treble (Treble control)
Use this feature to adjust high-frequencies output to your speakers
or headphones.
Choices: 2.5 kHz, 3.5 kHz, 8.0 kHz
Control range: – 6.0 dB to +6.0 dB
Initial setting: 0.0 dB
Control
Bass
Treble
Auto Bypass
Auto Bypass (Auto bypass)
Use this feature to select whether the audio output bypasses the tone
control circuitry when "Treble" and "Bass" are set to 0 dB (see
page 61).
Choice
Auto Automatically bypasses the tone control circuitry to
provide the purest signal possible when "Treble" and
"Bass" are set to 0 dB.
Off Does not bypass the tone control circuitry.
■ Lipsync (Audio and video synchronization)
Use this feature to adjust the audio and video synchronization.
HDMI Auto (HDMI automatic lip sync mode)
If the connected video monitor is connected to the HDMI OUT jack
on this unit and compatible with the automatic audio and video
synchronization function (automatic lip sync), this unit adjusts the
audio and video synchronization automatically. Use this feature to
activate or deactivate the automatic lip sync.
Functions
Speaker
Freq.: 350Hz
Gain: 0.0dB
+6
0
-6
Speaker
Freq.: 3.5kHz
Gain: 0.0dB
+6
0
-6
Functions