Resetting The System - Yamaha DSP-Z11 Owner's Manual

During Auto Setup
Error message
E01:No Front SP
E02:No Sur. SP
E03:No F. PRNS SP
E04:SBR → SBL
E05:Noisy
E06:Check Sur.
E07:No MIC
E08:No R.PRNS SP
E09:User Cancel
E10:Internal Err.
After Auto Setup
Warning message
W1:Out of Phase
W2:Over Distance
W3:Level Error
W4:SP Mismatch
Notes
• If the "ERROR" or "WARNING" screens appears, check the cause of the problem, then run "Auto Setup" again.
• If warning "W2" or "W3" appears, the adjustment are made, however the adjustments may not be optimal.
• Depending on the speakers, warning "W1" may appears even if the speakers connections are correct.
• If error "E10" occurs repeatedly, please contact a qualified Yamaha service center.

■ Resetting the system

Use this feature to reset all the parameters of this unit to the initial
factory settings.
Notes
• This procedure completely resets all the parameters of this unit including
the GUI menu parameters.
• The initial factory settings are activated next time you turn on this unit.
y
To cancel the initialization procedure at any time without making any
changes, press B MASTER ON/OFF on the front panel to release it
outward to the OFF position.
Press B MASTER ON/OFF on the front panel to
1
release it outward to the OFF position to turn off this
unit.
Cause
Front L/R channel signals are not detected.
A surround channel signal is not detected.
A front presence channel signal is not detected.
Only right surround back channel signal is detected. Connect the surround back speaker to the
Background noise is too loud.
Surround back speakers are connected, though
surround L/R speakers are not.
The optimizer microphone was unplugged during
the "Auto Setup" procedure.
A rear presence channel signal is not detected.
The "Auto Setup" procedure was cancelled due to
user activity.
An internal error occurred.
Cause
Speaker polarity is not correct. This message may
appear depending on the speakers even when the
speakers are connected correctly.
The distance between the speaker and the listening
position is over 24 m (80 ft).
The difference of volume level among speakers is
excessive.
The result of the wiring check of "Auto Setup" is
different from "Speaker Set" in "Manual Setup".
"Wiring" check procedure is skipped.
Remedy
Check the front L/R speaker connections.
Check the surround speaker connections.
Check the front presence speaker connections.
SUR.BACK/BI-AMP (SINGLE) terminal if you
only have one surround back speaker.
Try running "Auto Setup" in a quiet environment.
Turn off noisy electric equipment like air
conditioners or move them away from the optimizer
microphone.
Connect surround speakers when you use surround
back speakers.
Connect the supplied optimizer microphone to the
OPTIMIZER MIC jack on the front panel.
Check the rear presence speaker connections.
Run "Auto Setup" again.
Run "Auto Setup" again.
Remedy
Check the speaker connections for proper polarity
(+ or –).
Bring the speaker closer to the listening position.
Readjust the speaker installation so that all speakers
are set in locations with similar conditions.
Check the speaker connections.
Use speakers of similar quality.
Adjust the output volume of the subwoofer.
Use "Speaker Set" in "Manual Setup" to adjust the
speaker settings manually.
Select "Wiring" in "Setup Menu".
Press and hold I PROGRAM and then press
2
B MASTER ON/OFF inward to the ON position to
turn on this unit.
Press and hold IPROGRAM until "ADVANCED SETUP"
appears in the front panel display (see page 119).
Rotate I PROGRAM to select "INITIALIZE".
3
Press I PROGRAM repeatedly to select "ALL".
4
y
• Select "CANCEL" to cancel the initialization procedure without
making any changes.
• You can initialize the video parameters or sound field program
parameters separately. See page 120 for details.
Press B MASTER ON/OFF to release it outward to
5
the OFF position to confirm your selection and turn
off this unit.
Troubleshooting
See page
23
23
23
23
—
—
23
43
23
42
42
See page
23
—
—
23
—
42
84
44
127
En