Assembly; Assembling Steel Legs - Craftsman 113.206933 Owner's Manual

:/
Item
No.
unpacking and checking contents
TABLE OF LOOSE PARTS
TheFollowing P arts AreIn iudedWith
Model 113,206933 Only
DescripUon Qty.
A Leg, .4
B End Stiffener ............................... 2
C Side Stiffener .............................. 4
D Motor Support .............................. 1
E Motor ..................................... 1
Package of Miscellaneous Small Parts,
No. 67035, Consisting of the Following:
F Cord Clip .................................. 2
G Hex Nut, 1/4 in.-- 20
(approx. dia. of hole 1/4 in,) ................ 40
G Hex Nut, 5/16 in,-- 18
(approx. dla. of hole 5/16 in.) ................ 7
G Hex Nut, 1/2 in.-- 13
(approx. dia. of hole 1/2 in.) ................. 8
H TrussHd. Screw, 1/4in. --20x5/8 tn.
long. (Top of screw is rounded) ............. 40
J Flat Washer (dia. of hole 11/32 in.) ............. 7
K Lockwasher, 1/4 in. External Type
(approx. dia. of hole 1/4 in.) ................ 40
K Lockwasher, 5/16 in, External Type
(approx. dia. of hote 5/16 in.) ................ 7
L Carriage Bolt, 5/16 in. -- 18 x 3/4 tong .......... 3
M Leveling Foot .............................. 4
N Hex Hd. Screw, 5/16 in. -- 18 x 2 in ............. 3
ii i,, i ..................................
assembly
A
G
ASSEMBLING STEEL LEGS
NOTE: Steel Legs are furnished with Model 1t3.206933.
From among the foose parts, find the foilowin 9 Hardware:
40 Truss Head Screws, I/4-20 x 5/8
40 Lockwashers, 1/4-External
40 Hex Nuts, !/4-20
8 Hex Nuts, t/2-13
4 Leveling Feet
1. Assemble two (2) Side Stiffeners together Using four
(4) 1/4-20 Truss head screws, tockwasher and nuts.
Make two (2) Side Stiffener assemblies.
I
The End Stiffeners are placed on top and at each end
of Side Stiffener assemblies as shown. Align holes,
letter coded "B" (see page 8) in Side Stiffeners and ....-._ .....
End Stiffeners and then insert 1/'4-20 Truss head
screws through the 9/32 diameter hotes and install
Iockwashers and nuts and then tighten.
2. Assemble the four (4) Legs to the Side and End
Stiffeners using 1/4-20 screws, lockwashers and nuts
as sh own,
i
TRUSS HD. SCREW END STIFFENER
1/4-20 X _1/: EXTERNAL /
END 1 LOCKWASHER __
MOTOR SUPPORT
STIFFENERS
LEGS
3. Assemble the Motor Support to the Legs with 1/4-20
screws, Iockwashers and nuts. Motor Support can be
assembled to either end of Leg set.
4. Install leveling feet as shown. To level Leg Set, loosen
nut on inside of leg and turn nut on the outside to raise
or lower feet. Adjust all four leveling feet, if necessary,
and then tighten nuts on the inside of leg.
NOTE: These levelers are not intended for height
adjustment: