Table of Contents
Advertisement
will repair it, free of charge. This warranty appUesonly
while this product is in the United States.
If this table saw is used for commercial or rental purposes, this warranty wig apply for ninety days
/
from the date of purchase.
|
This warranty gives you specific legal rights, and you may also have other rights which vary from
J
state to state.
Sears, Roebuck and Co., D817 WA, Hoffman Estates, IL. 60179
SAFETY INSTRUCT|ONS
FOR TABLE SAW
Safety is a combination of common sense, staying alert
4.GROUND
THE SAW- This saw has an approved 3-
and knowing how your table saw works. Read this man-
conductor cord and a 3-prong grounding type plug.
ual to understand this saw.
The plug fits grounding type outlets designed for 120
volt 15 amp circuits.The green conductor in the cord is
BEFORE USING THE SAW
the NEVER connect the green wire to a live terminal.
5.To avoid injury form electrical shock, make sure your
fingers do not touch the plug's metal prongs when
plugging in or unplugging the saw.
6.To avoid back injury, get help or use recommended
casters when you need to move the saw. Always get
help if you need to lift the saw. Hold the saw close to
your body. Bend your knees so you can lift with your
legs, not your back.
7. NEVER STAND ON TOOL. Serious injury could occur
if the tool tips or you accidentally hit the cutting toolj
Do not store anything above or near the tool wher4
anyone might stand on the tool to reach them.
BEFORE EACH USE:
1. inspect your saw
A.To avoid injury from accidental starting, unplug the
saw, turn the switch off and remove the switch key
1. AVOID DANGEROUS EQUIPMENT. Use the saw in a
before raising or removing the Guard, changing the
dry place protected from rain. Keep work area well
cuttingtoo, changingthe setup or adjusting anything.
WARNING:
To avoid mistakes
that could cause_
serious, permanent injury, do not plug the saw in
I
until the following
steps have been satisfactorily
completed.
1. Assembly and Alignment. (See pages 12-31 )
2.Learn the use and function of the ON-OFF Switch,
Guard, Spreader, Anti-Kickback devise, Miter Gauge,
Fence, Table Insert and Blade Elevation and Bevel
Controls. (See pages 32-34)
3. Review and understanding of all safety instructions
and operating procedures in this manual.
4. Review of the maintenance methods for this saw. (See
page 46)
Read the DANGER label found on the front of the saw,
as shown below.
WHEN INSTALLING OR MOVING THE SAW
lighted.
2.To avoid injury from unexpected saw movement:
A.Put the saw on a firm level surface where there is
plenty of room for handling and properly supporting
the workpiece.
B.Support the saw so that the table is level and the
saw does not rock.
C.Bolt the saw to the floor it it tends to slip, walk or
slide during nomnal use.
D.When using table extensions over 24 inches wide
on any side of the saw, bolt the saw to the floor or
B. Check for alignment of moving parts, binding of
moving parts, breakage of parts, saw stability, and
any other conditions that may affect the way the saw
works. If any part is missing, bent or broken in any
way, or any electrical part does not work properly,
turn the saw off and unplug the saw.
C.Reptace damaged,
missing or failed
parts before
using the saw again.
D.Use the Sawblade Guard, Spreader and Anti-Kick-
back Pawls for any thru-sawing (whenever the blade
comes through the top of the workpiece). Make sure
the Pawls work properly. Make sure the Spreader is
prop up the outer end of the extension from the floor
in line with sawblade.
to keepthe saw from tipping.
E.REMOVE
ADJUSTING
KEYS AND WRENCHES.
3. Put the saw where neither Operator nor bystanders
Form habit of checking for and removing keys and
must stand in line with the saw blade,
adjusting wrenches from tool before turning it on.
I
_DANGER
1 Read manual before using saw.
4.Keep bade
guard down and in
7.When tipping,
use push stick when
9.When
ripping, use push blodk and
10.'Turn
power
off and wait for blade |
|2,Wear
safety goggles that meat
place for through cuts.
fence is set 2 inches or more from
auxiliary fence when fence is set
to stop before
adjusting
or
!
|
ANSI Z87.1 standerds.
5,Do not do freshand
cuts.
blade,
between l/2 and 2 inches from
servicing,
/
3.Do not reach around or over saw
6,Kesp hands out of path of saw
8.Kncw how to reduce the risk of
blade. Do not make rip cuts
blades,
blade,
kickback, See instrustions for ripping,
narrower than 1/2 inch.
2
Hide quick links:
Advertisement
Table of Contents
