Contents - Craftsman 113.206891 Owner's Manual

additional safety instructions for jointer-pUaner
i,
15: Never leave the Jointer-Planer work area with the
power on; before the Jointer-Planer has come to a
complete stop, or without removing and storing the
switch key.
16. Never operate the Jointer-Planerwith protectivecover
onthe unused shaft end of the motor removed.
17. Do not attempt to perform an abnormal or little-used
operation without study and the use of adequate hold
down/push blocks, jigs, fixtures, stops, etc.
18. DO NOT perform layout, assembly, or setup work on
the table while the cutting toot is rotating:
WARNING: THE 2" JOINTER-PLANER PULLEY AND
THE 2-1/2" MOTOR PULLEY FURNISHED WILL RUN
THE CUTTER HEAD AT APPROXIMATELY 4300 RPM
THAT A CARELESS FRACTION OF A SECOND IS
SUFFICIENT TO INFLICT SEVERE INJURY.
19. Read and follow the instructions appearing on the
danger label on the cutter guard.
DANGER
- FOR YOUR OWN SAFETY
READ AND UNDERSTAND OWNER'S
MANUAL BEFORE OPERATING MACHINE
1. WEAR SAFETY GOGGLES PER ANSI Z87.1 AT ALL TIMES.
2. NEVER PERFORM A JOINTING OR PLANING OPERATION WITH CUTTER
HEAD OR DRIVE GUARD REMOVED.
3. NEVER MAKE A JOINTING OR PLANING CUT DEEPER THAN 1/8 INCH.
4. ALWAYS USE HOLD DOWN!PUSH BLOCKS FOR JOINTtNG MATERIAL
NARROWER THAN 3 INCHES, OR PLANING MATERIAL THINNE_ THAN 3
INCHES.
WEAR YOUR
The operation of any power too_ can result in foreign
objects being thrown into the eyes, which can result in
severe eye damage. Always wear safety goggles complying
with ANSl Z87.1 (shown on Package) before commencing
power tool operation. Safety Goggles are available at
Sears retail or catalog stores.
m ' '_'_'
contents
POWER TOOL GUARANTEE ...................... 2
GENERAL: SAFETY INSTRUCTIONS FOR
POWER TOOLS ............................... 2
ADDITIONAL SAFETY INSTRUCTIONS FOR
JOINTER-PLANER ............................. 3
MOTOR SPECIFICATIONS AND ELECTRICAL
REQUIREMENTS .............................. 5
Connecting to Power Source Outlet ............. 5
Check Motor Rotation ........................ 5
UNPACKING AND CHECKING CONTENTS ......... 6
ASSEMBLY .............................. ....... 7
Assembling Steel Legs ........................ 7
Mounting Jointer-Planer On Recommended
Craftsman Leg Set .......................... 8
i Checking Cutterblades and Screws .............. 8
i Mounting Switch. _.;, _._. ...... ...... .. :.......9
Insta_i|ng Mot0r, Pulley, V-Belt and Belt Guards ... 9
• installing Siidi'ng Guard_:..... ....... .. :. ...... 10
GETTING TO KNOW YOUR JO1NTER-PLANER _.... 11
DePt h of Cut Handwheel :! .. _.,..., ::. :. .... ,..tl
i ,
4 i
i
Fence Locks and Stops ...................... 12
Fence Tilt Scale ............................ 12
Cutter Guard ............................... 13
Infeed Table ................................ 14
On-Off Switch .............................. 16
BASIC JOINTER-PLANER OPERATION ........... 17
Feeding the Workpiece ....................... 17
Using the Hold Down/Push Blocks ............. 18
Beveling ................................... 19
MAINTENANCE ................................ 19
Replacing Cutter Blades ..................... t9
Installing Cutter Guard Spring ................ 21
Sharpening Cutter Blades .................... 23
GENERAL MAINTENANCE ...................... 23
LU BRI CATION ................................. 23
MOTOR MAINTENANCE AND LUBRICATION ...... 24
TR OUBLE-SHOOTI N G .......................... 24
REPAIR PARTS ................................ 26
RECOMMENDED ACCESSORIES ................. 31