Table of Contents
Advertisement
Quick Links
INTRODUCTION
MOUNTING RECOMMENDATIONS
FAN INSTALLATION
CONTROL FEATURES:
INTELI•TOUCH OPERATION
WALL CONTROL PREPARATION
OPERATION
CHANGING TRANSMITTER FREQUENCY SETTING
BEZEL REPLACEMENT
Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product
and proper installation; therefore, before attempting to install and operate your Casablanca fan, read this
owner's manual completely and carefully. Retain this manual for future reference.
CAUTION: To avoid possible electrical shock, make certain that electricity is turned off at
the circuit breaker or fuse box before attempting any installation procedure.
• All wiring must be in accordance with the National Electric Code ANSI/NFPA 70-1993 and the appropriate local electrical
codes. The National Electric Code requires proper grounding as a precaution against electrical shock. A qualified electrician
should be consulted if you are unsure.
• This fan is designed to be installed on an existing electrical outlet box. The outlet box must be UL Listed for ceiling fan
installations, if it is not, a new box must be installed. Casablanca extension poles are available for sloped or high ceiling
installations.
• This ceiling fan requires a grounded electrical supply of 120 VAC, 60 Hz and a minimum 15 amp circuit. The maximum
current requirement for the fan with light fixture is 3.8 amps. The fan uses about 1 amp or 100 watts. Maximum light
current is 2.8 amps or 340 watts of lighting.
• Where wire nuts are employed, be sure all bare wires are within the connectors. When installing the canopy hatch, make
sure all wires are within the canopy and that no wires are being pinched.
use only genuine Casablanca blades, light fixtures, and accessories.
• The blades in each pack are matched for
equal weight to assure smooth fan operation.
If more than one fan is being installed, be
careful not to mix blades from different
cartons.
• Inspect the contents of your carton for
possible shipping or handling damage and
report any such damage directly to your
authorized Casablanca dealer.
• It is always a good idea to have an assistant
to help with the installation.
• When cleaning, painting, or working near
your fan, be very careful of the fan and
blades. Always turn the power OFF to the
ceiling fan before servicing it, working on
it, or replacing light bulbs.
• Never insert anything into the path of the
fan blades while the fan is in operation.
• Never install a fan over a pool or spa.
• Never operate a fan that has been damaged in
any way. Contact Casablanca Fan Company by
calling 1-888-227-2178, or contact your local
authorized Casablanca dealer for assistance
in obtaining service.
1
CONTENTS
READ AND SAVE THESE INSTRUCTIONS
SAFETY FIRST
BEFORE YOU START
For best performance and for your warranty to be valid,
SAFE USE
FUSE BOX
(REMOVE FUSE FOR THE
CIRCUIT YOU WILL BE
WORKING ON)
CIRCUIT BREAKER
(TRIP BREAKER FOR THE
CIRCUIT YOU WILL BE
WORKING ON)
PN 9943001 RL1210
18"
70"
84"
1
2
3
12
11
15
16
19
1
Advertisement
Table of Contents
Related Manuals for Casablanca 19th Century
Summary of Contents for Casablanca 19th Century
-
Page 1: Safety First
CONTENTS INTRODUCTION MOUNTING RECOMMENDATIONS FAN INSTALLATION CONTROL FEATURES: INTELI•TOUCH OPERATION WALL CONTROL PREPARATION OPERATION CHANGING TRANSMITTER FREQUENCY SETTING BEZEL REPLACEMENT READ AND SAVE THESE INSTRUCTIONS SAFETY FIRST Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product and proper installation; therefore, before attempting to install and operate your Casablanca fan, read this owner’s manual completely and carefully. -
Page 2: Mounting Recommendations
MOUNTING RECOMMENDATIONS Before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air circulation, and fan size are all important factors to consider before installation. Location Ceiling fans have practical uses in almost every room in your home. We suggest you follow these mounting recommendations as you decide where to install your Casablanca fan. • For safety reasons, the fan blades must be a minimum of 7′ above the floor. • Do not locate the fan in a doorway or above a swinging door. • In any installation, the tips of the blades must be at least 18″ from the wall in order to provide sufficient clearance for the blades. • In bedrooms, fans work best when mounted above the foot of the bed. • Over pool tables, be sure to provide plenty of clearance to avoid damage from pool cues. • In kitchens be sure to allow for open cupboard doors to clear the fan blades. • Do not install a fan close to, or over, a pool or spa. High humidity combined with corrosive gases will destroy the finish and warp the blades. Fan Size Variable fan speed capability permits the use of a full-size 52″ fan even in smaller rooms. For very large rooms, two fans may be needed. SLOPED CEILING INSTALLATIONS MAXIMUM Suggested Extension Pole Lengths HANG-TRU® EXTENSION ANGLE 32º POLE Ceiling Height Pole Length... - Page 3 Century ™ PREPARATION INSTRUCTIONS Unpacking: Before assembling and installing your ceiling fan, remove all parts from the shipping cartons and check them against the parts listed here. Before discarding packaging material, be certain that all parts have been removed. GETTING STARTED Carton Contents Be sure to use only genuine Casablanca blades. The blade The fan carton contains the fan body, warranty card, owner’s shrink wrap holds 4 blades of matched weight. If more than manual, and all the parts necessary to assemble and install one fan is being installed, be sure not to mix blade sets. your Casablanca ceiling fan. These parts are shown at the start of each installation section. Before you start, go through this Owner’s Manual and confirm that you have all the parts CAUTION: When removing the shrink wrap, shown in each section.
-
Page 4: Fan Installation
FAN PREPARATION IMPORTANT SAFETY INFORMATION! BEFORE STARTING THE INSTALLATION OF YOUR CEILING FAN, INSTALL THE THREADED DOWNROD INTO THE MOTOR COUPLING AND LOCK THE ASSEMBLY Prepare for fan installation as follows: Step D. Route the wires from the motor through the GROUND Perma •... - Page 5 Century ™ CEILING HARDWARE ADDITIONAL HARDWARE ” x 8-32 ROUNDED HEAD SCREW (2) CROSSBAR WIRE NUT (4) 1” x 8-32 ROUNDED MOUNTING FLAT WASHER (2) HEAD SCREW (2) BRACKET SUPPORT INSTALLATION PARTS LARGE LAG SCREW FLAT WASHER ” #7 X 5” (1) ”...
- Page 6 LAG SCREWW INSATALLATION Step 3. With the large washer attached, pass the lag screw through the center hole of the crosbar mounting bracket and screw into guide hole. Tighten until outlet box is firmly mounted to beam. This box must be firmly secured to the ceiling. We recommend that the ceiling fixture outlet box be of sufficient capacity enabling it to support the weight of fan and light fixture under any conditions. SCREW LARGE WASHER CANOPY HARDWARE CANOPY SCREW (4) CANOPY CANOPY LOCK WASHER (4) HATCH CANOPY CANOPY INSTALLATION Step 4. Attach the canopy to the crossbar mounting bracket with three of the 8-32 x 2 ” long canopy screws and lock washers provided with your Casablanca fan. Hand tighten until snug against the ceiling.
- Page 7 Century ™ HANGING THE FAN Step 5. To hang the fan body in the canopy, hold the fan CANOPY body firmly and insert the nylon ball into the canopy opening. Rotate fan body until slot on nylon ball fits into pin opposite canopy opening. NOTE: The fan weight is 35 pounds. BALL SLOT CANOPY ELECTRICAL CONNECTIONS Step 6. Connect the fan wires to the outlet box wiring by placing the bare ends of the wires 2 BLACK WIRES together and then securing with a wire nut. Connect in this order: • GREEN leads from mounting plate and fan to GROUND conductor of power source. Secure 2 WHITE WIRES with wire nut.
- Page 8 DISASSEMBLE CANOPY AND MOTOR COVERS Step 10. Remove the screws from the canopy cover and the motor cover and set aside for later use. MOTOR COVER CANOPY COVER INSTALL CANOPY COVER Step 11. Take the two pieces of the canopy cover and assemble them around CANOPY the downrod as shown. Using the four COVER screws removed in Step 10, assemble the canopy cover. Slide the canopy cover to the ceiling and secure to the downrod using the two provided screws. Tighten by hand only. SCREWS FROM STEP 10 CAUTION: The canopy cover can NOT be used on sloped ceilings.
- Page 9 Century ™ BLADE HARDWARE BLADE BLADE BLADE WASHER BLADE SCREW HOLDER ATTACH BLADE HOLDERS BLADE Step 13. Attach the blades to the blade holders by aligning SCREW the screw holes of the holder with the holes of the blade. BLADE Attach the blade holder using the four blade screws and WASHER blade washers provided for each blade. Using the screwdriver, tighten securely by hand only. INSTALL BLADE ASSEMBLY Step 14. Remove the blade holder screw from the fan. Slide the blade assembly into the cross bar, assuring that the alignment holes line up. Reinstall the blade holder screw, making sure that the blade BLADE HOLD- assembly is secure and does not rotate when turned.
- Page 10 SWITCH HOUSING CUP INSTALLATION Note: If you have purchased the exclusive accessory light fixture for this fan, please go to Step 16. If not please continue with Step 15. Step 15. Slide the switch housing cup over the threaded pipe from the switch housing. Assure that no wires are pinched. Secure the cup to the fan with the finial. Tighten securely by hand only. THREADED PIPE FINIAL SWITCH HOUSING...
-
Page 11: Wall Control Preparation
® W-84 WALL CONTROL PREPARATION WALL CONTROL AND HARDWARE (not to scale) Switch Mounting Screws (2) Switch Bezels (4) Wire Cap Wall Plate W-84 (1) White Screws White Wall Almond Wall Wall Control (pre-installed) (2) White Plate (1) Plate (1) (1) Almond (2) Almond Prepare for W-84 Wall Control Bezel replacement... - Page 12 ® RUBBER KEY Prepare for W-84 Wall Control installation - Continued Step 1d. Before attaching the bezel back on to the front of the switch, make sure that the rubber key ALMOND LOCATING pad is attached to the locating pins on the bezel as PINS BEZEL shown in Figure #4.
- Page 13 ® W-84 CONTROL INSTALLATION INSTALLING THE W-84 WALL CONTROL NOTE: W-84 Wall Control should only be installed on Casablanca's Inteli-Touch 3 fans with UPLIGHTS ONLY ® or both an UPLIGHT and a DOWNLIGHT on the fan. The wall control installs in the same manner as an ordinary light switch, using an existing wall box and wiring. This controller is designed to signal the fan microcomputer as well as perform normal switching operations.
- Page 14 ® DUAL W-84 INSTALLATION DIP SWITCHES To control the fan and lights from two locations (a three-way circuit), use two W-84 wall controls as shown in the wiring diagram in Figure #1. Before installing the two switches into the wall, place both switches side by side, then locate the 4 dip switches on the side of the two switches as shown in Figure #2.
-
Page 15: Operation
® OPERATION POWER button is normally left in the on position. Always turn the power off during cleaning or servicing the fan and during thunderstorms. It is also used to exit or enter additional programs. button must be left on to retain a previously set fan speed or light level. OPERATION SPEED CONTROL There are six individual speed settings for the fan;... - Page 16 ® OPERATION LIGHTS To dim just the up light: 1. Make sure you have just the downlight on. NOTE: Light Operation - 2. Turn the light off, then press and hold the button. After one the light varies from “bright” second, the up light will come on at their lowest setting and gradually be- to “dim”...
- Page 17 ® AUTOMATIC DEMONSTRATION PROGRAM Programmed into every Inteli-Touch Series fan is an ® Automatic Demonstration Program. It can be used to A multi-tone signal will verify the start of the test pro- fully demonstrate and test the operation of the fan. gram which proceeds as follows: •...
- Page 18 ® OPERATION HOME-SAFE PROGRAM ® The Home-Safe Program makes an unoccupied home appear occupied by turning the lights on and off at random times. To enter the Home-Safe Program: 1) To operate the lights and fan for Home Safe Program – Press the But- ton off for a least 5 seconds.
-
Page 19: Bezel Replacement
® IN THE WALL BEZEL REPLACEMENT WALL CONTROL AND HARDWARE (not to scale) Switch Mounting Screws (2) (4) Wire Cap Wall Plate W-84 Switch Bezels Screws White Wall Almond Wall Wall Control (1) White (2) White Plate(1) Plate(1) (1) Almond (2) Almond WARNING! To avoid possible electrical shock, make cer-... - Page 20 WHITE BEZEL W-84 Wall Control Bezel replacement: - CONTINUED Step 1c. Locate the rubber key pad attached to the four (4) locating pins and remove rubber key pad from the WHITE bezel, also as shown in Figure #3. LOCATING PINS (4) LOCATING PINS HOLES(4)
- Page 21 BEZEL W-84 Wall Control Bezel replacement: - CONTINUED Step 1e. To attach the bezel back on to the front of the switch you will need to align the four (4) tabs on the bezel with the front of the wall control and by gently pressing on both top and bottom of the bezel at the same time, snap BEZEL the bezel back on to the front of the switch as shown in...
- Page 22 Consult the dealer or an experienced radio/TV technician for help. Note: Any changes or modifications to the transmitter or receiver not expressly approved by Casablanca Fan Company may void one’s authority to operate this remote control.
- Page 23 CARE RECOMMENDATIONS Fan Finishes • For cleaning, a soft brush or lint-free cloth should be used to prevent scratching the finish. • A vacuum cleaner brush nozzle can remove heavier dust. • Surface smudges or an accumulation of dirt and dust can be removed easily using a mild detergent and slightly dampened soft cloth.