Casablanca Stealth Instructions Manual

Casablanca Stealth Instructions Manual

Hide thumbs Also See for Stealth:

Advertisement

INTRODUCTION
mOUNTINg ReCOmmeNDaTIONs
PRePaRaTION INsTRUCTIONs
faN INsTaLLaTION
CONTROL feaTURes:
INTELI•TOUCH OPERATION
INTELI•TOUCH TROUBLESHOOTING
READ AND SAVE THESE INSTRUCTIONS
Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product
and proper installation; therefore, before attempting to install and operate your Casablanca fan, read this
owner's manual completely and carefully. Retain this manual for future reference.
CAUTION: To avoid possible electrical shock, make certain that electricity is turned off
at the circuit breaker or fuse box before attempting any installation procedure.
• CAUTION: RISK OF ELECTRICAL SHOCK! All wiring must be performed in accordance with national and local electrical
codes. If you are unfamiliar with the wiring codes, you should use a qualified electrician. To avoid overheating and pos-
sible damage to other equipment, do not install control to a receptacle, fluorescent light fixture, motor operated appliance,
or transformer-supplied appliance..
• This fan is designed to be installed on an existing electrical outlet box. The outlet box must be UL Listed for ceiling fan
installations, if it is not, a new box must be installed. Casablanca extension poles are available for sloped or high ceiling
installations.
• This ceiling fan requires a grounded electrical supply of 120 VAC, 60 Hz and a minimum 15 amp circuit. The maximum
current requirement for the fan with light fixture is 2 amps. The fan uses about 1 amp or 100 watts. Maximum light current
is 1.0 amps or 100 watts of lighting.
• Where wire nuts are employed, be sure all bare wires are within the connectors. When installing the canopy hatch, make
sure all wires are within the canopy and that no wires are being pinched.
use only genuine Casablanca blades, light fixtures, and accessories.
• The blades in each pack are matched for equal
weight to assure smooth fan operation. If more
than one fan is being installed, be careful not to
mix blades from different cartons.
• Inspect the contents of your carton for possible
shipping or handling damage and report any such
damage directly to your authorized Casablanca
dealer.
• It is always a good idea to have an assistant to help
with the installation.
• When cleaning, painting, or working near your fan,
be very careful of the fan and blades. Always turn
the power OFF to the ceiling fan before servicing
it, working on it, or replacing light bulbs.
• Never insert anything into the path of the fan blades
while the fan is in operation.
• Never install a fan over a pool or spa.
• Never operate a fan that has been damaged in
any way. Contact Casablanca Fan Company by
calling toll free 1-888-227-2178, or contact your
local authorized Casablanca dealer for assistance
in obtaining service.
CONTENTS

SAFETY FIRST

BEFORE YOU START
For best performance and for your warranty to be valid,
SAFE USE
(remove fuse for The
circuiT you will be
working on)
CIRCUIT BREAKER
(Trip breaker for The
circuiT you will be
working on)
PN 3243Z
S
FUSE BOX
HN1209
®
tealth
16
18"
70"
84"
1
1
2
3
4
8

Advertisement

Table of Contents
loading

Summary of Contents for Casablanca Stealth

  • Page 1: Safety First

    • Never install a fan over a pool or spa. • Never operate a fan that has been damaged in any way. Contact Casablanca Fan Company by calling toll free 1-888-227-2178, or contact your local authorized Casablanca dealer for assistance in obtaining service.
  • Page 2: Mounting Recommendations

    MOUNTING RECOMMENDATIONS Before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air circulation, and fan size are all important factors to consider before installation. Location Ceiling fans have practical uses in almost every room in your home. We suggest you follow these mounting recommendations as you decide where to install your Casablanca fan.
  • Page 3: Perma • Lock™ Hardware

    ® tealth STEALTH INSTALLATION INSTRUCTIONS Unpacking: Before assembling and installing your ceiling fan, remove all parts from the shipping cartons and check them against the parts listed here. Before discarding packaging material, be certain that all parts have been removed. PERMA •...
  • Page 4: Ceiling Hardware

    CEILING HARDwARE ADDITIONAL HARDWARE ” x 8-32 ROUNDED HEAD SCREw (2) CROSSBAR wIRE NUT (4) 1” x 8-32 ROUNDED FLAT wASHER MOUNTING HEAD SCREw (2) BRACkET SUPPORT INSTALLATION PARTS LARGE LAG SCREw FLAT wASHER ” #7 X 5” (1) ” (1) CROSSBAR MOUNTING BRACkET INSTALLATION JOIST Note: after removing the old fixture, check the outlet...
  • Page 5: Lag Screw Installation

    ® tealth LAG SCREw INSTALLATION Step 3. With the large washer attached, pass the lag screw through the center hole of the crosbar mounting bracket and screw into guide hole. Tighten until outlet box is firmly mounted to beam. This box must be firmly secured to the ceiling. We recommend that the ceiling fixture outlet box be of sufficient capacity enabling it to support the weight of fan and light fixture under any conditions.
  • Page 6: Attaching The Blades

    ATTACHING THE BLADES Step 3a. Attach the 5 blade tips to the blades using two 3a - BLADE TIP INSTALLATION: 6-32x ⁄ ” round head screws provided. Note: the screws have locktite on them, so once they are installed it will 6-32x ⁄...
  • Page 7: Canopy Hatch Installation

    ® tealth CANOPY HATCH INSTALLATION Step 6. Tuck the wires into the canopy with the wire nuts pointed upwards, so that the white and black wires are HATCH CANOPY on opposite sides of the canopy and all wires are clear of the canopy opening.
  • Page 8: Control Installation

    ® W-85 CONTROl INSTAllATION WALL CONTROL AND HARDWARE (not to scale) (4) Wire Cap Wall Plate W-85 Switch Bezels switch Mounting Screws White Wall Almond Wall Wall Control (1) White Screws (2) (2) White Plate(1) Plate(1) (1) Almond (2) Almond WARNINg! BEZEL To avoid possible electrical shock, make cer- tain that electricity is turned off at the circuit...
  • Page 9 ® W-85 Wall Control Bezel replacement: - aLMOND CONTINUED BEZEL Step 17c. Reinstall the rubber key pad on to the four (4) locating pins located on the almond bezel as shown in Figure #3 and #4. RUBBER KEY Figure #3 RUBBER KEY Step 17d.
  • Page 10: Installing The W-85 Wall Control

    ® INSTAllINg ThE W-85 WAll CONTROl NOTE: W-85 Wall Control should only be installed on Casablanca's Inteli-Touch 3 fans with DOWNLIGHTS ONLY. ® The wall control installs in the same manner as an ordinary light switch, using an existing wall box and wiring. This controller is designed to signal the fan microcomputer as well as perform normal switching operations.
  • Page 11: Dual W-85 Installation

    ® DUAL w-85 INSTALLATION DIP SWITChES To control the fan and lights from two locations (a three-way circuit), use two W-85 wall controls as shown in the wiring diagram in Figure #5. Before installing the two switches into the wall, place both switches side by side, then locate the 4 dip switches on the side of the two switches.
  • Page 12 ® OPERATION POwER button is normally left in the on position. Always turn the power off during cleaning or servicing the fan and during thunderstorms. It is also used to exit or enter additional programs. button must be left on to retain a previously set fan speed or light level. OPERATION SPEED CONTROL There are six individual speed settings for the fan;...
  • Page 13: Changing Frequency Setting

    ® CHANGING FREqUENCY SETTING noTe: all fans leave the factory set to “1111” SWITChES You will only have to change the dip switch settings in the remote if you are using more than one fan in the same area and want to control them separately. Step 1.
  • Page 14: Operation Safe-Exit

    ® OPERATION SAFE-EXIT AND LIGHT -MINDER PROGRAM ® ® NOTE: Both Light-Minder and safe-exit programs will always run at the same time. The Safe-Exit Program gives you about thirty seconds of light when you turn the lights off, enabling you to exit your home before the lights go out. To enter the Safe-Exit Program: Safe-Exit 1) To operate the lights for safe-exit program – press the button off for at...
  • Page 15: Operation Fan-Minder

    ® OPERATION FAN-MINDER PROGRAM ™ The Fan-Minder feature will add to your comfort when used in the bedroom. The program reduces the speed of the fan each two-hour interval to compensate for cooling night air. To enter the Fan-Minder program: 1. Turn the OFF for at least 5 seconds. 2. Turn the 3. Immediately operate the buttons in the following sequence: 4.
  • Page 16: Troubleshooting Tips

    Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Note: any changes or modifications to the transmitter or receiver not expressly approved by Casablanca Fan Company may void one’s authority to operate this remote control.
  • Page 17: Product Specifications

    ® tealth PRODUCT SPECIFICATIONS Model Name: stealth Motor: XLp-2000 ® ® Model Number: 32xxZ Blade Span: 54" Blade Iron Pitch: 14° Dimensions: A = 10.8" No. of Blades: B = 13.25" Technology: Inteli•Touch 3 W-85 ® C = 3" Lightbulb: (1) 100-watt halogen NOTE: Dimension B D = 11.5"...

Table of Contents