Advertisement
Quick Links
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
MOUNTING RECOMMENDATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
VERSA•TOUCH OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
PRODUCT SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product and proper
installation; therefore, before attempting to install and operate your Casablanca fan, read this owner's manual com-
pletely and carefully. Retain this manual for future reference.
CAUTION: To avoid possible electrical shock, make certain that electricity is turned off at the
circuit breaker or fuse box before attempting any installation procedure.
• All wiring must be in accordance with the National Electric Code ANSI/NFPA 70-1993 and the appropriate local electrical
codes. The National Electric Code requires proper grounding as a precaution against electrical shock. A qualified electrician
should be consulted if you are unsure.
• This fan is designed to be installed on an existing electrical outlet box. The outlet box must be UL Listed for ceiling fan
installations, if it is not, a new box must be installed. Casablanca extension poles are available for sloped or high ceiling
installations.
• This ceiling fan requires a grounded electrical supply of 120 VAC, 60 Hz and a minimum 15 amp circuit. The maximum
current requirement for the fan with light fixture is 1.48 amps Star / 1.28 amps Starlet. The fan uses about .85 amps (102
watts) Star / .65 amps (78 watts) Starlet. Maximum light current is .63 amps or 75 watts of lighting.
• Where wire nuts are employed, be sure all bare wires are within the connectors. When installing the canopy hatch, make
sure all wires are within the canopy and that no wires are being pinched.
use only genuine Casablanca blades, light fixtures, and accessories.
•
The blades in each pack are matched for equal
weight to assure smooth fan operation. If more
than one fan is being installed, be careful not
to mix blades from different cartons.
• Inspect the contents of your carton for possible
shipping or handling damage and report any
such damage directly to your authorized
Casablanca dealer.
• It is always a good idea to have an assistant
to help with the installation.
• When cleaning, painting, or working near your
fan, be very careful of the fan and blades.
Always turn the power OFF to the ceiling fan
before servicing it, working on it, or replacing
light bulbs.
• Never insert anything into the path of the fan
blades while the fan is in operation.
• Never install a fan over a pool or spa.
• Never operate a fan that has been damaged in
any way. Contact Casablanca Fan Company
by calling 1-888-227-2178), or contact your
local authorized Casablanca dealer for
assistance in obtaining service.
CONTENTS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
READ AND SAVE THESE INSTRUCTIONS
SAFETY FIRST
BEFORE YOU START
For best performance and for your warranty to be valid,
SAFE USE
(REMOVE FUSE FOR THE
CIRCUIT YOU WILL BE
(TRIP BREAKER FOR THE
CIRCUIT YOU WILL BE
PN C2843001
FUSE BOX
WORKING ON)
CIRCUIT BREAKER
WORKING ON)
AT0209
18"
70"
84"
1
Advertisement
Related Manuals for Casablanca Star
Summary of Contents for Casablanca Star
-
Page 1: Table Of Contents
CONTENTS INTRODUCTION ..............1 MOUNTING RECOMMENDATIONS . -
Page 2: Mounting Recommendations
MOUNTING RECOMMENDATIONS Before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air circulation, and fan size are all important factors to consider before installation. Location Ceiling fans have practical uses in almost every room in your home. We suggest you follow these mounting recommen- dations as you decide where to install your Casablanca fan. • For safety reasons, the fan blades must be a minimum of 7′ above the floor. • Do not locate the fan in a doorway or above a swinging door. • In any installation, the tips of the blades must be at least 18″ from the wall in order to provide sufficient clearance for the blades. • In bedrooms, fans work best when mounted above the foot of the bed. -
Page 3: Fan Installation
™ ™ tarlet INSTALLATION INSTRUCTIONS Unpacking: Before assembling and installing your ceiling fan, remove all parts from the shipping cartons and check them against the parts listed here. Before discarding packaging material, be certain that all parts have been removed. SETUP Setup: Remove the fan body from the box and place the body of the fan on top of a cloth on a flat surface. This will protect the fan body from being scratched during assembly. PERMA • LOCK™ HARDWARE LOCKING BOLT DOWNROD & BALL (MOTOR COUPLING) ASSEMBLY FAN PREPARATION IMPORTANT SAFETY INFORMATION! BEFORE STARTING THE INSTALLATION OF YOUR CEILING FAN, INSTALL THE THREADED DOWNROD INTO THE MO- TOR COUPLING AND LOCK THE ASSEMBLY GROUND WIRE... - Page 4 CEILING HARDWARE 1″ x 8-32 ROUND HEAD SCREWS (2) WIRE NUT (4) FLAT WASHER (2) LAG SCREW AND WASHER CROSSBAR MOUNTING BRACKET GETTING STARTED Installing a New Ceiling Fixture Outlet Box Using Existing Ceiling Fixture Outlet Box If you do not have an existing fixture located where you After turning the power OFF at its source (either circuit wish to place your Casablanca fan, an approved ceiling breaker or fuse box), lower the old fixture and discon- fixture outlet box must be installed and wired.
- Page 5 ™ ™ tarlet CANOPY HARDWARE CANOPY HATCH CANOPY SCREW (4) CANOPY LOCK PHILLIPS WASHER (4) SCREWDRIVER CANOPY CANOPY INSTALLATION Step 2. Attach the canopy to the crossbar mounting bracket with three of the 8-32 x 2 ″ long canopy screws and canopy lock washers. Tighten the screw firmly by hand only. Note: On sloped ceilings, align the canopy opening towards the CROSSBAR top or room peak.
- Page 6 BLADE HARDWARE BLADE BLADE SCREW RUBBER WASHER METAL WASHER (4 PER BLADE) (4 PER BLADE) (4 PER BLADE) BLADE INSTALLATION Step 3. Assemble the blades BLADE SCREW to the motor using the blade & WASHERS screws, rubber washers and metal washers. Hand tighten firmly. BLADE SCREW METAL WASHER RUBBER WASHER...
- Page 7 ™ ™ tarlet HANGING THE FAN Step 4. To hang the fan body in the canopy, hold the fan body firmly and insert the ball into the canopy opening. BALL Check that no wires were pinched. Rotate the fan body until the slot in the nylon ball fits into the pin opposite the canopy opening. SLOT CANOPY ELECTRICAL CONNECTIONS Step 5a. Attach the fan wires to the ceiling fixture outlet box wiring by twisting the bare ends of the wires together and then securing with a wire nut. Test that the connection is secure by pulling on the wire nut. Connect in this order: 2 BLACK WIRES Step 5b.
- Page 8 ATTACHING THE LIGHT FIXTURE STEPS 9a - 9c Step 9a. Before getting started, remove the rubberband from the plug connector. Step 9b. Install two of the three light adapter screws into the light adapter plate. Thread the plug connec- tor through the hole in the center of the light adapter plate.
- Page 9 ™ ™ tarlet INSTALLING THE HALOGEN BULB IMPORTANT! When installing the halogen bulb, carefully cut off the end of the plastic sleeve the bulb comes in and hold the bulb by the plastic sleeve to screw it into the socket. Step 10. Screw the 75-watt halogen bulb into the socket. Do not touch the glass bulb with your fingers it is extremely important that the glass be clean. If it is accidentally touched, or dirty, clean carefully with a tissue. A dirty glass will cause the bulb to fail almost immediately. HALOGEN BULB NOTE: In compliance with US Federal Energy LIGHT Regulations, this ceiling fan contains a device SOCKET HALOGEN that restricts the light fixture to a maximum of BULB 190 watts. Exceeding that limit or the marked limit on this product may result in a fire hazard or improper operation. INSTALLING THE GLASS SHADE Step 11.
-
Page 10: Versa•Touch Operation
VERSA•TOUCH2™ CONTROL INSTALLATION VERSA•TOUCH2™ HARDWARE (not to scale) Wood Screw Screw Drywall Screw 6-32 X " 6-32 X 1" 12v Battery Anchor 1" (2) 6-32 (2) W-72 W-72 Control Control Holder CONTROL BRACKET INSTALLATION SAFETY FIRST: To reduce the risk of electrical shock, this fan must be installed with an isolating wall control/ switch. CAUTION! Do not use with wall dimmer. WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid state speed control device. Use only the control provided with this fan. Step 12. Follow instructions for the type of transmitter control bracket you will be using. STANDARD TOGGLE ROCKER SWITCH LIGHT SWITCH INNER MOUNTING OUTER HOLES MOUNTING SWITCH HOLES COVER... -
Page 11: Control Features
® REMOTE OPERATION Fan Control To start the fan. Press the selected speed button to run the fan at the desired speed. Send Signal LIGHT LOW=Low speed MED=Medium speed HIGH=High speed To turn off the fan, press the FAN OFF button. Airflow Direction To reverse the airflow, press the REVERSE button. REVERSE operates at any speed HIGH whether the fan is on or off. The fan returns to its set speed after reversing. Light Control Turn the light on or off independently from the fan by pressing the LIGHT button. If you press the button for more than 0.7 seconds, it becomes a dimmer. The light varies from “bright" to “dim” over approximately 8 seconds. If you continue to hold REVERSE the LIGHT button, this sequence will reverse when the light reaches its brightest or dimmest level. Release the button when the desired level is reached. Memory Feature The last light fuction and fan speed will resume when power is turned back on. Auto Resume Quick (pressing less than 0.7 seconds) on/off operation of the LIGHT button maintains the desired brightness level set previously. -
Page 12: Troubleshooting
TROUBLESHOOTING TIPS Please refer to this troubleshooting guide before requesting service or contacting your dealer for assistance. PROBLEM POSSIBLE REMEDIES Fan will not start • Check the main circuit fuses, circuit breakers, and wall switch position. Check all wire connections. Make sure the power is turned off during this inspection. •... -
Page 13: Product Specifications
™ ™ tarlet PRODUCT SPECIFICATIONS 172mm x 20mm Direct Drive ™ Model Name: Star™ Motor: Model Number: C28GXXM Blade Span: 52" Blade Iron Pitch: 15° No. of Blades: Dimensions: A = 11.8" Versa•Touch2 ® W-72 Technology: B = 14.35" Lightbulb: (1) 75-watt halogen C = 3"...