1. Manuals
  2. Brands
  3. Casablanca Manuals
  4. Fan
  5. 19 Century
  6. Owner's manual

Casablanca 19 Century Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
INTRODUCTION
mOUNTINg ReCOmmeNDaTIONs
faN INsTaLLaTION
OpTIONaL LIghT fIxTURe INsTaLLaTION
CONTROL feaTURes:
INTeLI•TOUCh OpeRaTION
TROUbLeshOOTINg
aDVaN•TOUCh OpeRaTION
TROUbLeshOOTINg
Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product
and proper installation; therefore, before attempting to install and operate your Casablanca fan, read this
owner's manual completely and carefully. Retain this manual for future reference.
cauTion: To avoid possible electrical shock, make certain that electricity is turned off at
the circuit breaker or fuse box before attempting any installation procedure.
• All wiring must be in accordance with the National Electric Code ANSI/NFPA 70-1993 and the appropriate local electrical
codes. The National Electric Code requires proper grounding as a precaution against electrical shock. A qualified electri-
cian should be consulted if you are unsure.
• This fan is designed to be installed on an existing electrical outlet box. The outlet box must be UL Listed for ceiling fan
installations, if it is not, a new box must be installed. Casablanca extension poles are available for sloped or high ceiling
installations.
• This ceiling fan requires a grounded electrical supply of 120 VAC, 60 Hz and a minimum 15 amp circuit. The maximum
current requirement for the fan with light fixture is 3.8 amps. The fan uses about 1 amp or 100 watts. Maximum light
current is 2.8 amps or 340 watts of lighting.
• Where wire nuts are employed, be sure all bare wires are within the connectors. When installing the canopy hatch, make
sure all wires are within the canopy and that no wires are being pinched.
use only genuine Casablanca blades, light fixtures, and accessories.
• The blades in each pack are matched for
equal weight to assure smooth fan operation.
If more than one fan is being installed, be
careful not to mix blades from different
cartons.
• Inspect the contents of your carton for
possible shipping or handling damage and
report any such damage directly to your
authorized Casablanca dealer.
• It is always a good idea to have an assistant
to help with the installation.
• When cleaning, painting, or working near
your fan, be very careful of the fan and
blades. Always turn the power OFF to the
ceiling fan before servicing it, working on
it, or replacing light bulbs.
• Never insert anything into the path of the
fan blades while the fan is in operation.
• Never install a fan over a pool or spa.
• Never operate a fan that has been damaged in
any way. Contact Casablanca Fan Company by
calling 1-888-227-2178, or contact your local
authorized Casablanca dealer for assistance
in obtaining service.
CONTENTS
READ AND SAVE THESE INSTRUCTIONS

SAFETY FIRST

BEFORE YOU START
For best performance and for your warranty to be valid,
SAFE USE
FUSE BOX
(remove fuse for The
circuiT you will be
working on)
CIRCUIT BREAKER
(Trip breaker for The
circuiT you will be
working on)
P/N6943020 AT0507
18"
70"
84"
1
2
3
10
12
15
16
19


Advertisement

Table of Contents
loading

Related Manuals for Casablanca 19 Century

Summary of Contents for Casablanca 19 Century

  • Page 1: Safety First

    READ AND SAVE THESE INSTRUCTIONS SAFETY FIRST Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product and proper installation; therefore, before attempting to install and operate your Casablanca fan, read this owner’s manual completely and carefully. Retain this manual for future reference.

  • Page 2: Mounting Recommendations

    A mINImUm OF 7′ When to Use Extension Poles ABOVE THE FLOOR For best performance and best appearance, an extension pole should be used with 7′ mINImUm your Casablanca fan when installing on high (cathedral) ceilings or sloped ceil- ings. Casablanca offers standard poles in increments of 6″ up to 5′. Custom poles are available in lengths up to 10′. See your Authorized Casablanca Dealer for details.
  • Page 3 Century ™ PREPARATION INSTRUCTIONS Unpacking: Before assembling and installing your ceiling fan, remove all parts from the shipping cartons and check them against the parts listed here. Before discarding packaging material, be certain that all parts have been removed. GETTING STARTED Carton Contents Be sure to use only genuine Casablanca blades. The blade The fan carton contains the fan body, warranty card, owner’s shrink wrap holds 4 blades of matched weight. If more than manual, and all the parts necessary to assemble and install one fan is being installed, be sure not to mix blade sets. your Casablanca ceiling fan. These parts are shown at the start of each installation section. Before you start, go through this Owner’s Manual and confirm that you have all the parts CAUTION: When removing the shrink wrap, shown in each section.

  • Page 4: Fan Installation

    Installing a New Ceiling Fixture Outlet Box Using Existing Ceiling Fixture Outlet Box If you do not have an existing fixture located where you wish After turning the power OFF at its source (either circuit to place your Casablanca fan, an approved ceiling fixture breaker or fuse box), lower the old fixture and disconnect outlet box must be installed and wired. the wiring. Check the ceiling fixture outlet box to be sure that it is marked ‘Approved for ceiling fan mounting’ . If it is warning: To reduce the risk of fire, electrical shock, not, a new box must be installed.
  • Page 5 Century ™ CEILING HARDWARE addiTional hardware ” x 8-32 ROUNDED HEAD SCREW (2) CROSSBAR mOUNT- WIRE NUT (4) 1” x 8-32 ROUNDED INg BRACKET FLAT WASHER (2) HEAD SCREW (2) SUPPORT INSTALLATION PARTS LARgE LAg SCREW FLAT WASHER ” #7 X 5” (1) ”...
  • Page 6 CANOPy SCREW (4) CANOPy CANOPy LOCK WASHER (4) HATCH CANOPy CANOPY INSTALLATION Step 4. Attach the canopy to the crossbar mounting bracket with three of the 8-32 x 2 ” long canopy screws and lock washers provided with your Casablanca fan. Hand tighten until snug against the ceiling. note: On sloped ceilings, align the canopy opening toward the top or peak of the room. CANOPy LOCK WASHER FEED OUTLET BOX WIRES THROUgH...
  • Page 7 Century ™ HANGING THE FAN Step 5. To hang the fan body in the canopy, hold the fan CANOPy body firmly and insert the nylon ball into the canopy open- ing. Rotate fan body until slot on nylon ball fits into pin opposite canopy opening. noTe: The fan weight is 35 pounds. BALL SLOT CANOPY ELECTRICAL CONNECTIONS Step 6. Connect the fan wires to the outlet box wiring by placing the bare ends of the wires 2 BLACK WIRES together and then securing with a wire nut. Connect in this order: • GREEN leads from mounting plate and fan to GROUND conductor of power source. Secure 2 WHITE WIRES with wire nut.
  • Page 8 DISASSEMBLE CANOPY AND MOTOR COVERS Step 10. Remove the screws from the canopy cover and the motor cover and set aside for later use. mOTOR COVER CANOPy COVER INSTALL CANOPY COVER Step 11. Take the two pieces of the canopy cover and assemble them around CANOPy the downrod as shown. Using the four COVER screws removed in Step 10, assemble the canopy cover. Slide the canopy cover to the ceiling and secure to the downrod using the two pro- vided screws. Tighten by hand only. SCREWS FROm STEP 10 CAUTION: The canopy cover can NOT be used on sloped ceilings.
  • Page 9 Century ™ BLADE HARDWARE BLADE BLADE BLADE WASHER BLADE SCREW HOLDER ATTACH BLADE HOLDERS BLADE Step 13. Attach the blades to the blade holders by align- SCREW ing the screw holes of the holder with the holes of the blade. BLADE WASHER Attach the blade holder using the four blade screws and blade washers provided for each blade. Using the screwdriver, tighten securely by hand only. INSTALL BLADE ASSEMBLY Step 14. Remove the blade holder screw from the fan. Slide the blade assembly into the cross bar, assuring that the alignment holes line up. Reinstall the blade holder screw, making sure that the blade BLADE HOLD- assembly is secure and does not rotate when turned.

  • Page 10: Optional Light Fixture Installation

    SWITCH HOUSING CUP INSTALLATION note: If you have purchased the exclusive accessory light fixture for this fan, please go to Step 16. If not please continue with Step 15. Step 15. Slide the switch housing cup over the threaded pipe from the switch housing. Assure that no wires are pinched. Secure the cup to the fan with the finial. Tighten securely by hand only. THREADED PIPE FINIAL SWITCH HOUSINg OPTIONAL LIGHT FIXTURE INSTALLATION Step 16. Remove the wire nuts on the BLACK...
  • Page 11 Century ™ INSTALL LIGHT KIT Step 18. Slide the light kit over the threaded pipe from the switch housing. Assure that no wires are pinched. Secure the light kit to the fan with the finial. Tighten securely by hand only. THREADED PIPE FINIAL GLASS HARDWARE 60 WATT TyPE g-16.5 CANDELABRA-BASE BULB gLASS SHADE GLASS & BULB INSTALLATION Step 19. Loosen the three glass screws for each fixture so the end of the screws are flush with the inside of the fixture. gLASS SHADE Slide the glass shade into the fixture and hold SCREWS...
  • Page 12 Inteli•Touch ® INTELI•TOUCH INSTALLING THE W-32 WALL CONTROL The wall control installs in the same manner as an ordinary light switch, using an existing junction box and wiring. This controller is designed to signal the fan microcomputer as well as perform normal switching operations. For this reason the following precautions must be observed: 1. Use only the Casablanca W-32 wall control. 4. No other light fixtures or electrical appliances may be 2. Do not use any additional control with your Inteli-Touch connected on the circuit controlled by the W-32 wall fan (for example, dimmer, fan speed control, etc.). control. 3. Do not use more than one fan per wall control. INTELI•TOUCH f SINGLE W-32 INSTALLATION CAUTION! Ensure power is turned OFF at the breaker or fuse panel before starting installation.

  • Page 13: Inteli•Touch Operation

    Inteli•Touch ® INTELI•TOUCH OPERATION f POWER The button is normally left in the on position. Always turn the POWER power off during cleaning or servicing the fan and during thunderstorms. It is also used to exit or enter additional programs. POWER must be left on to retain a previously set fan speed or light level. INTELI•TOUCH OPERATION f SPEED CONTROL There are six individual speed settings for the fan; each speed is indicated by an audible tone of increasing pitch. FAN CONTROL To select the desired fan speed: 1. With fan off, press and hold the button labeled .
  • Page 14 Inteli•Touch ® INTELI•TOUCH OPERATION f LIGHT -MINDER PROGRAM ® The Light-Minder program automatically turns OFF the fan mounted lights after two hours. To enter the Light-minder Program: 1. Turn the OFF for at least three seconds. POWER 2. Turn the POWER 3. Immediately operate the buttons in the following sequence: LIGHT LIGHT 4. A series of tones indicates this command has been accepted. The fan and light will operate normally using the buttons to turn them on and off. But, if the lights are left on, they will automatically shut off after two hours. To cancel the Light-Minder Program, turn the off for three seconds. POWER INTELI•TOUCH OPERATION f SAFE-EXIT PROGRAM ® The Safe-Exit Program gives you about thirty seconds of light when you turn the lights off, enabling you to exit your home before the lights go out. To enter the Safe-Exit Program: 1. Turn the off for at least three seconds.

  • Page 15: Troubleshooting

    FAN OR LIgHTS APPEAR TO OPERATE By THEmSELVES (CHANgINg SPEED OR INTENSITy), WALL CONTROL OPERATION IS INTERmIT- TENT: Check AC supply for irregularities, (noise spikes, fluctuations, or failure); or circuit board assembly. For questions or to locate the nearest Casablanca Authorized Service Center call toll free: 1-888-227-2178 or visit us on the web at:...
  • Page 16 •T ™ DVAN OUCH SAFETY FIRST Warning: To reduce the risk of electrical shock, this fan must be installed with an isolating wall control/switch. ADVAN•TOUCH W-62 BRACKET/HOLSTER REMOVAL Step 1. Remove the two 6-32 x 5/16” screws holding the bracket to the holster. Save screws for later. BRACKET HOLSTER ADVAN•TOUCH CONTROL BRACKET INSTALLATION CAUTION! Do not use with wall dimmer or rocker switch.

  • Page 17: Advan•Touch Operation

    •T ™ DVAN OUCH ADVAN•TOUCH BATTERY INSTALLATION Open Battery Door Install 4 “AAA” alkaline by pressing down on b atteries in the space the insert tab pro- p rovided. Please observe vided. proper polarity placement. Replace Battery Door. BATTERY DOOR ADVAN•TOUCH IMPORTANT OPERATING NOTES Power turned off, interrupted or failure: The remote control is battery operated, therefore if the power is turned off, interrupted or you experience a power failure, the remote control remembers the previous setting for both fan and light.
  • Page 18 •T ™ DVAN OUCH SECURITY FEATURE Pressing the ‘SECURITY’ button will start the Security lighting program. The controller beeps and indicates ‘SECURITY’ . The light will automatically turn ON and OFF in a seemingly random manner over an eight and a quarter hour programmed cycle that is designed to give the home a “lived-in” look. Regardless of the light setting when switching to the Security mode (lights on or off, dim or bright), the lights will increase to high brightness and then begin the Security cycle. This cycle is then repeated continuously until cancelled by pressing the ‘SECURITY’ button. At any time during the Security mode you may adjust the fan speed, reverse the direction, operate in Auto Speed or Winter, use Saver or run the Test mode without affecting SECURITY MODE CYCLE Security mode.

  • Page 19: Troubleshooting

    Increase the separation between the equipment and receiver, Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Note: Any changes or modifications to the transmitter or receiver not expressly approved by Casablanca Fan Company may void one’s authority to operate this...

Table of Contents