Sntp Commands Set; Table 3.16: Sntp Commands Set - Advantech EKI-7657C User Manual

systemlog mode
[client|server|both]
show systemlog
show systemlog
no systemlog
smtp enable
smtp serverip
[IP address]
smtp authentication
smtp account
[account]
smtp password
[password]
smtp rcptemail
[Index] [Email address]
show smtp
no smtp
event device-cold-start
[Systemlog|SMTP|Both]
event authentication-failure
[Systemlog|SMTP|Both]
event ring-topology-change
[Systemlog|SMTP|Both]
event systemlog
[Link-UP|Link-Down|Both]
event smtp
[Link-UP|Link-Down|Both]
show event
no event device-cold-start
no event authentication-failure
no event ring-topology-change
no event systemlog
no event smpt
show systemlog
3.1.16

SNTP Commands Set

Table 3.16: SNTP Commands Set

Netstar Commands
sntp enable
sntp daylight
sntp daylight-period
[Start time] [End time]
sntp daylight-offset
[Minute]
sntp ip
[IP]
sntp timezone
[Timezone]
show sntp
Specified the log mode
G
Displays system log.
E
Show system log client & server
P
information
Disable systemlog functon
G
Enable SMTP function
G
Configure SMTP server IP
G
Enable SMTP authentication
G
Configure authentication account
G
Configure authentication password
G
Configure Rcpt e-mail Address
G
Show the information of SMTP
P
Disable SMTP function
G
Set cold start event type
G
Set Authentication failure event
G
type
Set X - ring topology changed
G
event type
Set port event for system log
I
Set port event for SMTP
I
Show event selection
P
Disable cold start event type
G
Disable Authentication failure
G
event type
Disable X - ring topology changed
G
event type
Disable port event for system log
I
Disable port event for SMTP
I
Show system log client & server
P
information
Level Description
Enable SNTP function
G
Enable daylight saving time, if
SNTP function is inactive, this
G
command can't be applied.
Set period of daylight saving time,
if SNTP function is inactive, this
command can't be applied.
G
Parameter format:
[yyyymmdd-hh:mm]
Set offset of daylight saving time, if
SNTP function is inactive, this
G
command can't be applied.
Set SNTP server IP, if SNTP
function is inactive, this command
G
can't be applied.
Set timezone index, use "show
sntp timzezone" command to get
G
more information of index number
Show SNTP information
P
37
switch(config)# systemlog mode both
Switch>show systemlog
switch#show systemlog
switch(config)#no systemlog
switch(config)#smtp enable
switch(config)#smtp serverip 192.168.1.5
switch(config)#smtp authentication
switch(config)#smtp account User
switch(config)#smtp password
switch(config)#smtp rcptemail 1
switch#show smtp
switch(config)#no smtp
switch(config)#event device-cold-start both
switch(config)#event authentication-failure both
switch(config)#event ring-topology-change both
switch(config)#interface fastethernet 3
switch(config-if)#event systemlog both
switch(config)#interface fastethernet 3
switch(config-if)#event smtp both
switch#show event
switch(config)#no event device-cold-start
switch(config)#no event authentication-failure
switch(config)#no event ring-topology-change
switch(config)#interface fastethernet 3
switch(config-if)#no event systemlog
switch(config)#interface fastethernet 3
switch(config-if)#no event smtp
switch#show systemlog
Example
switch(config)#sntp enable
switch(config)#sntp daylight
switch(config)# sntp daylight-period 20060101-
01:01 20060202-01-01
switch(config)#sntp daylight-offset 3
switch(config)#sntp ip 192.169.1.1
switch(config)#sntp timezone 22
switch#show sntp
Alert@test.com
Chapter3