Advertisement
Quick Links
IARMOR EDGE™
BEFORE INSTALLATION
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE
PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE
STARTING INSTALLATION. ASSISTANCE IS RECOMMEND-
ED. THANK YOU FOR CHOOSING OUR PRODUCT!
*ROCKER PANEL MOUNT
*DRILLING NOT REQUIRED
PART LIST
Driver Front Mounting
Bracket (DFM)
Driver Center Mount-
ing Bracket (DCM)
Pedal
Driver Rear Mount-
ing Bracket (DRM)
Drain
Hole at
Bottom
Driver Side Step Bar
iArmor
Note:
Step bars are NOT interchangeable.
Make sure drain holes at the bottom will be
located at the rear direction of the step bars.
Customer Support: info@iarmorauto.com
Torque Value
Fastener Size
Tightening Torque (ft-lbs)
6mm
8mm
10mm
12mm
14mm
Front
1
®
PART#: IA-N280H
6-7
16-18
31-32
56-58
92-94
Passenger Front
Mounting Bracket
(PFM)
Passenger Center
Mounting Bracket
(PCM)
Passenger Rear
Mounting Bracket
(PRM)
Drain
Hole at
Bottom
Passenger Side Step Bar
Rev. 20221201
Required
X
√
X
X
X
Pedal
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for APS IARMOR EDGE IA-N280H
Summary of Contents for APS IARMOR EDGE IA-N280H
- Page 1 iArmor ® IARMOR EDGE™ PART#: IA-N280H Torque Value BEFORE INSTALLATION Fastener Size Tightening Torque (ft-lbs) Required REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. ASSISTANCE IS RECOMMEND- 16-18 √ ED. THANK YOU FOR CHOOSING OUR PRODUCT! 10mm 31-32 *ROCKER PANEL MOUNT...
- Page 2 iArmor ® Hardware Package A (For Brackets & Bars Installation) Item Description Item Description M8X1.25-30 Hex Bolts M8X1.25-20 T-Bolts M8 Large Flat Washers M8 Plastic Washers M8 Lock Washers M8 Nylon Lock Nuts Hardware Package B (For Step Pedals Installation) Item Description Item...
- Page 3 iArmor ® The instruction here is for your reference only. We strongly recommend the professional installer for best result. We are not responsible for any damage caused by the installation. STEP 1 Install (4) Pedals onto the step bars with (24) M8X1.25-25mm Hex Bolts, (24) M8 Large Flat Washers and (24) M8 Lock Washers.
- Page 4 iArmor ® Plastic Deflector M8 Plastic Washer Remove Factory Hex Bolts M8X1.25-20 T-Bolt (Fig 5) Thread (1) M8 Plastic Washer on each T-Bolt Before In- serting into the slot !!! Insert the T-bolt (Fig 3) Passenger Rear Mounting Bracket Location with M8 Plastic Thread down the M8 Washer in the...
- Page 5 iArmor ® Attention Do periodic inspections to the installation to make sure that all hardware is secure and tight. In order to protect your bars/boards, please use mild soap/non-abrasive products for cleaning only. (6) M8 Plastic Washers (6) M8X1.25-20mm T-Bolts (6) M8 Large Flat Washers (6) M8 Nylon Lock Nuts Front...
Need help?
Do you have a question about the IARMOR EDGE IA-N280H and is the answer not in the manual?
Questions and answers