Advertisement
Quick Links
IARMOR EDGE™
BEFORE INSTALLATION
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE
PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE
STARTING INSTALLATION. ASSISTANCE IS RECOMMEND-
ED. THANK YOU FOR CHOOSING OUR PRODUCT!
*ROCKER PANEL MOUNT
*DRILLING/TRIMMING NOT REQUIRED
PART LIST
Driver Front Support
Bracket (DFS)
Pedal
Drain
Hole at
Bottom
Driver Side Step Bar
iArmor
Driver Front
Mounting
Bracket (DFM)
Driver Center /
Passenger Rear
Mounting Bracket
(DCM/PRM)
(PCM/DRM)
Note: *
Driver Center & Passenger Rear Mounting Brackets
are universal. *Passenger Center & Driver Rear Mounting
Brackets are universal. *Step bars are NOT interchangeable.
Make sure drain holes at the bottom will be located at the rear
direction of the step bars.
Customer Support: info@iarmorauto.com
1
Torque Value
Fastener Size
6mm
8mm
10mm
12mm
14mm
Front
Passenger Front Support
Passenger Front
Mounting Brack-
et (PFM)
Passenger Center /
Driver Rear Mount-
ing Bracket (PCM/
DRM)
®
PART#: IA-N171H
Tightening Torque (ft-lbs)
6-7
16-18
31-32
56-58
92-94
Bracket (PFS)
(DCM/PRM)
Drain
Hole at
Bottom
Passenger Side Step Bar
Rev. 20221201
Required
√
√
X
X
X
Pedal
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for APS IARMOR EDGE IA-N171H
Summary of Contents for APS IARMOR EDGE IA-N171H
- Page 1 iArmor ® IARMOR EDGE™ PART#: IA-N171H Torque Value BEFORE INSTALLATION Fastener Size Tightening Torque (ft-lbs) Required REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE √ PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. ASSISTANCE IS RECOMMEND- 16-18 √ ED. THANK YOU FOR CHOOSING OUR PRODUCT! 10mm 31-32 *ROCKER PANEL MOUNT...
- Page 2 iArmor ® Hardware Package A (For Brackets & Bars Installation) Item Description Item Description M8 Plastic Washers M6X1-20 Square Head Bolts M8X1.25-30 Hex Bolts M6 Large Flat Washers M8 Large Flat Washers M6X1 Nylon Lock Nuts M8 Lock Washers M8X1.25-20 T- Bolts M8X1.25 Nylon Lock Nuts Hardware Package B (For Step Pedals Installation) Item...
- Page 3 iArmor ® The instruction here is for your reference only. We strongly Remove plugs if equipped recommend the professional installer for best result. We are not responsible for any damage caused by the installation. STEP 1 Front Install (4) Pedals onto the step bars with (24) M8X1.25-25mm Hex Bolts, (24) M8 Large Flat Washers and (24) M8 Lock Washers.
- Page 4 iArmor ® STEP 3 Assemble Passenger Front Mounting Bracket (PFM) and Pas- PCM/DRM senger Front Support Bracket (PFS) with (1) M8X1.25-30mm Hex Bolt, (2) M8 Large Flat Washers and (1) M8 Nylon Lock Nut, (Fig 5). Do not fully tighten at this time. (2) M8X1.25-30mm Hex Bolts (2) M8 Large Flat Washers (2) M8 Lock Washers...
- Page 5 iArmor ® STEP 8 Level and adjust the assembled Step Bar properly and tighten all hardware. Insert the T-bolt Move to the other side of the vehicle. Repeat Steps 2-7 for the with M8 Plastic Thread down the M8 other side step bar installation. Washer in the Plastic Washer slot on the step...
- Page 6 iArmor ® (Fig 11) Passenger Side Step Installation (5) M8 Plastic Washers (5) M8X1.25-20mm T-Bolts (5) M8 Large Flat Washers (5) M8 Nylon Lock Nuts Front Bottom View (Fig 12) M6 Square Bolt in the Channel (1) M6X1-20mm Square Head Bolt (1) M6 Large Flat Washer (1) M6 Nylon Lock Nut Customer Support: info@iarmorauto.com...
Need help?
Do you have a question about the IARMOR EDGE IA-N171H and is the answer not in the manual?
Questions and answers