Panasonic PT-D10000 Operating Instructions Manual page 81

Note
• The air filter cleaning monitor (FILTER CLEANING)
will flash blue while cleaning of the air filter is in
progress. If there is a problem with the air filter, the
air filter cleaning monitor (FILTER CLEANING) will
light red.
• The time taken for cleaning is approximately 30 to
40 seconds.
• The setting time will be the local time. p. 81
• Automatic cleaning will not be carried out if the
projector is in standby mode.
• If the projector is not in projection mode when the
setting time is reached, automatic cleaning will not
be carried out.
• Automatic cleaning will not be carried out if 24 hours
have not yet elapsed since cleaning was last
carried out (either by automatic cleaning or forced
cleaning).
Example: If the setting time is 7:00 and forced
cleaning is carried out at 9:00, then
automatic cleaning will not be carried out at
7:00 on the following day.
46 hours elapsed 46 hours elapsed
22 hours elapsed 22 hours elapsed
Setting time Setting time Setting time Setting time
Automatic Automatic Forced Forced (No cleaning) (No cleaning)
cleaning cleaning cleaning cleaning
• If the time is set to a time which is within 24
hours from the last time cleaning was carried out,
automatic cleaning will not be carried out the next
time the setting time is reached. Instead, cleaning
will be carried out when the setting time is reached
on the following day.
Example: If cleaning was carried out at 10:00, and
the cleaning time setting is then changed to
20:00, automatic cleaning will be carried out
at 20:00 on the following day.
34 hours elapsed 34 hours elapsed
10 hours elapsed 10 hours elapsed
Setting time Setting time Setting time Setting time
Automatic Automatic (No cleaning) (No cleaning)
cleaning cleaning
Time reset Time reset
• When projection starts (when the power is
turned on), automatic cleaning will be carried out
immediately if more than 24 hours have elapsed
since cleaning was last carried out.
Setting the date and time
This lets you set the time zone and the current date
and time for the projector's internal clock.
1. Press ▲▼ to select "DATE AND
TIME".
OPTION2 OPTION2
PROJECTOR ID PROJECTOR ID
INSTALLATION INSTALLATION
ALTITUDE ALTITUDE
DIRECTION DIRECTION
LAMP SELECT LAMP SELECT
LAMP RELAY LAMP RELAY
RS-232C RS-232C
SYSTEM INFORMATION SYSTEM INFORMATION
AIR FILTER CLEANING AIR FILTER CLEANING
DATE AND TIME DATE AND TIME
STARTUP LOGO STARTUP LOGO
PASSWORD PASSWORD
ENTER ENTER
2. Press ENTER.
• The "DATE AND TIME" screen will be
displayed.
DATE AND TIME DATE AND TIME
TIME ZONE TIME ZONE
ADJUST CLOCK ADJUST CLOCK
Setting time Setting time
LOCAL DATE LOCAL DATE
LOCAL TIME LOCAL TIME
Automatic Automatic
cleaning cleaning
3. Press ▲▼ to select "TIME ZONE".
4. Press ◄► to switch "TIME ZONE".
5. Press ▲▼ to select "ADJUST
CLOCK".
6. Press ENTER.
• The "ADJUST CLOCK" screen will be
displayed.
ADJUST CLOCK ADJUST CLOCK
YEAR YEAR
MONTH MONTH
DAY DAY
HOUR HOUR
MINUTE MINUTE
APPLY APPLY
Setting time Setting time
Automatic Automatic
7. Press ▲▼ to select the item to
cleaning cleaning
be set, and use ◄► to set the
local time.
8. Use ▲▼ to select "APPLY", and
then press ENTER.
• This completes setting of the time.
2 2
FRONT-F FRONT-F
LOW LOW
H H
QUAD QUAD
OFF OFF
LOGO1 LOGO1
MENU SELECT MENU SELECT
SUB MENU SUB MENU
09:00 09:00
2007/01/01 2007/01/01
12:34:56 12:34:56
MENU SELECT MENU SELECT
CHANGE CHANGE
2007 2007
1 1
1 1
12 12
34 34
MENU SELECT MENU SELECT
CHANGE CHANGE
81
ENGLISH –