Panasonic PT-D10000 Operating Instructions Manual page 104

Using the serial terminals (continued)
Basic format
Transmission from the computer begins with STX, then the ID, command, parameter, and ETX are sent in this
order. Add parameters according to the details of control.
STX STX
Start Start
(1 byte) (1 byte)
Attention
• No command can be sent or received for 10 to 60 seconds after the lamp starts lighting. Try sending any
command after that period has elapsed.
• When transmitting multiple commands, be sure to wait until 0.5 of a second has elapsed after receiving the
response from the projector before sending the next command. When sending commands without parameters, a
colon (:) is not necessary.
Note
• When the wrong command is sent, the "ER401" or "ER402" status is sent from the projector to the personal
computer.
• Projector ID supported on the RS-232C interface is ZZ (ALL) and a group of 1 to 64 and 0A to 0Z.
• The "STX" character code is 02 and the "ETX" character code is 03.
• If a command is sent with a projector ID specified, the projector will return answer back only in the following
cases:
If it coincides with the projector ID,
ID specification is ALL and VPS-SYSTEM is the master,
or ID specification is group and Group is the master.
Control commands
When controlling the projector from a computer, the following commands are available:
Command Function of command Command Function of command
PON PON
POF POF
IIS IIS
Switch input modes Switch input modes
QSL QSL
Query for active lamp mode Query for active lamp mode
LPM LPM
Note
• If you need a detailed command list, please contact your dealer.
104
– ENGLISH
A D A D I 1 I 2 I 1 I 2
(2 bytes) (2 bytes) Two ID Two ID
Semicolon Semicolon
characters characters
(2 bytes) (2 bytes)
ZZ, 1 to 64 and 0A to 0Z ZZ, 1 to 64 and 0A to 0Z
ID designate ID designate
In standby mode, commands other than "PON" are invalid. In standby mode, commands other than "PON" are invalid.
Power "ON" Power "ON"
• • While the lamp is ON and being controlled, a "PON" command will not be While the lamp is ON and being controlled, a "PON" command will not be
Power "OFF" Power "OFF"
accepted. accepted.
Parameter Parameter
VID = VIDEO VID = VIDEO
RG1 = RGB1 RG1 = RGB1
Parameter Parameter
0 = QUAD, 1 = L1/L4, 2 = L2/L3, 3 = DUAL, 4 = L1/L2/L3, 5 = L1/L2/L4, 0 = QUAD, 1 = L1/L4, 2 = L2/L3, 3 = DUAL, 4 = L1/L2/L3, 5 = L1/L2/L4,
6 = L1/L3/L4, 7 = L2/L3/L4, 8 = TRIPLE, 9 = L1, 10 = L2, 11 = L3, 12 = L4, 6 = L1/L3/L4, 7 = L2/L3/L4, 8 = TRIPLE, 9 = L1, 10 = L2, 11 = L3, 12 = L4,
13 = SINGLE 13 = SINGLE
Parameter Parameter
0 = QUAD, 1 = L1/L4, 2 = L2/L3, 3 = DUAL, 4 = L1/L2/L3, 5 = L1/L2/L4, 0 = QUAD, 1 = L1/L4, 2 = L2/L3, 3 = DUAL, 4 = L1/L2/L3, 5 = L1/L2/L4,
Active lamp mode Active lamp mode
6 = L1/L3/L4, 7 = L2/L3/L4, 8 = TRIPLE, 9 = L1, 10 = L2, 11 = L3, 12 = L4, 6 = L1/L3/L4, 7 = L2/L3/L4, 8 = TRIPLE, 9 = L1, 10 = L2, 11 = L3, 12 = L4,
13 = SINGLE 13 = SINGLE
; ; C1 C1 C2 C2 C3 C3
Colon Colon
(1 byte) (1 byte)
(1 byte) (1 byte)
3 command 3 command
characters characters
(3 bytes) (3 bytes)
SVD = S-VIDEO SVD = S-VIDEO
RG2 = RGB2 RG2 = RGB2
: : P1 P1 P2 P2 Pn Pn
Parameter Parameter
(undefined length) (undefined length)
Remarks Remarks
DVI = DVI-D DVI = DVI-D
AUX = AUX AUX = AUX
ETX ETX
End End
(1 byte) (1 byte)