Denon AVR-2312CI Owner's Manual page 123

6
Pressing ui, select the first letter of the device
brand name. Then press ENTER .
REMOTE SETUP GUIDE
1
Please select the first letter of
A
the brand name of the device.
B
C
D
E
Device : DVD
F
G
H
I
Select Enter Return
RETURN
• The first character is displayed as 1, A to Z.
(Initials for the brand are displayed for each
category.)
For brand names that start with numbers
and symbols, select "1".
7
Pressing ui, select the device
brand name. Then press ENTER .
REMOTE SETUP GUIDE
-DVD-
Please select brand name.
Dantax
Denon
Disney
DSE
Durabrand
Select Enter Return
RETURN
• When there are several pages of brand
names, the pages can be switched by
CH +
pressing the remote control unit's or
CH –
.
NOTE
If the desired brand name is not listed, the supplied remote control
unit cannot control the device. Use the remote control unit supplied
with the device to be used.
8
The procedures for registering remote control codes
and remote control preset registration are displayed.
REMOTE SETUP GUIDE
Device : DVD
Brand : DENON
Code [1/3] : 30490
1. Press [INPUT SOURCE].
2. Press and hold [DEVICE ON ( l )] for 3 seconds.
3. Input code with [0-9].
4. Press any key to check device. (e.g. [DEVICE ON ( l )])
OK NG
QUICK1 QUICK2
Press QUICK 1 if device works, QUICK 2 if not
NOTE
If a wrong brand name is selected, press
following screen is displayed:
REMOTE SETUP GUIDE
Device : DVD
Brand : DENON
Code [1/3] : 30490
Press [AMP] button.
And press [ENTER] button to return
1. Press [INPUT SOURCE].
Brand select menu.
2. Press and hold [DEVICE ON ( l )] for 3 seconds.
3. Input code with [0-9].
4. Press any key to check device. (e.g. [DEVICE ON ( l )])
OK
OK NG
QUICK1 QUICK2
Press QUICK 1 if device works, QUICK 2 if not
AMP ENTER
Press then to return to step 7.
9
Press the input source button on which the preset
code is to be registered ( BD , SAT/CBL
V.AUX DOCK GAME1 GAME2
, , , or
TV
• For , only the preset code for the categories "TV", "TV/DVD", or
"TV/VCR" can be registered.
10
Press and hold ZONE/DEVICE Z for at least 3 seconds.
The zone mode indicator flashes twice.
120
11
Enter a five-digit code using
Press the buttons with an interval less than 10 seconds.
Device
Brand
Code [1/3]
1. Press [INPUT SOURCE].
2. Press and hold [DEVICE ON ( l )] for 3 seconds.
3. Input code with [0-9].
4. Press any key to check device. (e.g. [DEVICE ON ( l )])
Return
QUICK3
QUICK1
Press QUICK 1 if device works, QUICK 2 if not
• When the code is registered.
The zone mode indicator flashes twice.
QUICK SELECT 3
. The
• When the code is not registered correctly
The mode indicator slowly flashes once. Perform from step 9
again.
• When an input number is not correct
ON
Press once then perform the operations from step 9 again.
12
Operate the device being used to check the operation.
• If the device is operating, press
Go to step 13.
• If the device is not operating, press
Return
Go to step 14.
QUICK3
13
The screen shown below is displayed, and registration
of the preset code is completed.
, TV , DVD ,
CD
).
Device
Brand
Code [1/3]
1. Press [INPUT SOURCE].
2. Press and hold [DEVICE ON ( l )] for 3 seconds.
3. Input code with [0-9].
4. Press any key to check device. (e.g. [DEVICE ON ( l )])
QUICK1
Press QUICK 1 if device works, QUICK 2 if not
• The menu screen is retrieved. Press
Registering preset codes
0 – 9 .
REMOTE SETUP GUIDE
: DVD
: DENON
: 30490
OK NG Return
QUICK2 QUICK3
QUICK SELECT 1
.
QUICK SELECT 2
.
REMOTE SETUP GUIDE
: DVD
: DENON
: 30490
Remote Setup Guide is finished.
Press [AMP] button.
And press [ENTER] button to return
MENU.
OK
OK NG Return
QUICK2 QUICK3
AMP ENTER
then .
vSee overleaf