Denon AVR-2312CI Owner's Manual page 101

n Audyssey Settings
Set Audyssey MultEQ ® XT, Audyssey Dynamic EQ ® and Audyssey Dynamic Volume ® . These can be
selected after Audyssey ® Auto Setup has been performed. For additional information on Audyssey
technology, please see page 137.
NOTE
• If you have not performed Auto Setup, or if you change the speaker settings after performing Auto Setup,
you may not be able to select Dynamic EQ ® /Dynamic Volume ® .
In this case, either perform Audyssey ® Auto Setup over again or perform "Restore" (vpage 25) to
return to the settings after Audyssey ® Auto Setup was run.
• When HD Audio for which the sampling frequency exceeds 96 kHz is played back, the "Audyssey
Settings" cannot be set.
Setting items
MultEQ ® XT
Audyssey : Optimize the frequency response of all speakers.
MultEQ ® XT corrects
Audyssey Byp.L/R : Optimize frequency response of speakers except
both time and frequency front L and R speakers.
response problems in the Audyssey Flat : Optimize frequency response of all speakers to flat
listening area based on response.
Audyssey ® Auto Setup
Manual : Apply frequency response set with "Manual EQ" (vpage 99).
OFF : Turn "MultEQ ® XT" equalizer off.
calibration. We recommend
"Audyssey".
MultEQ ® XT is the
• "Audyssey", "Audyssey Byp. L/R" and "Audyssey Flat" can be selected
prerequisite function for
after Audyssey ® Auto Setup has been performed. "Audyssey" is
Dynamic EQ ® and Dynamic
automatically selected after performing Audyssey ® Auto Setup. When
Volume ® .
"Audyssey", "Audyssey Byp. L/R" or "Audyssey Flat" is selected,
illuminates.
• After running Audyssey ® Auto Setup, if the Speaker Configuration,
Distance, Channel Level, and Crossover Frequency have changed
without increasing the number of speakers measured, only
illuminates.
NOTE
• "MultEQ ® XT" and "Manual" cannot be selected when "EQ Customize"
is set to "Not Used" (vpage 107).
• When using headphones, "MultEQ ® XT" is automatically set to "OFF".
"MultEQ ® XT", "Dynamic EQ ® " and "Dynamic Volume ® " settings are stored for each input source.
BD
Default settings are underlined.
Setting details
Setting items
Dynamic EQ ® ON : Use Dynamic EQ ® .
OFF : Do not use Dynamic EQ ® .
Solve the problem of
deteriorating sound quality
as volume is decreased
or
by taking into account
human perception and
room acoustics. Works with
MultEQ ® XT.
Reference Level Offset 0dB (Film Ref) : This is the default setting and should be used when
Audyssey Dynamic EQ ® is
listening to movies.
referenced to the standard 5dB : Select this setting for content that has a very wide dynamic range,
film mix level. It makes such as classical music.
adjustments to maintain 10dB : Select this setting for jazz or other music that has a wider dynamic
the reference response range. This setting should also be selected for TV content as that is usually
and surround envelopment mixed at 10 dB below film reference.
when the volume is turned 15dB : Select this setting for pop/rock music or other program material
down from 0 dB. However, that is mixed at very high listening levels and has a compressed dynamic
film reference level is not range.
always used in music or
Setting is enabled when "Dynamic EQ ® " is "ON" (vpage 98).
other non-film content.
Dynamic EQ ® Reference
Level Offset provides three
offsets from the film level
reference (5 dB, 10 dB, and
15 dB) that can be selected
when the mix level of the
content is not within the
standard.
Dynamic Volume ®
Midnight : Most adjustment to loudest and softest sounds.
Solve the problem of large Evening : Medium adjustment to loudest and softest sound.
variations in volume level Day : Least adjustment to loudest and softest sounds.
OFF : Do not use "Dynamic Volume ® ".
between TV, movies and
other content (between
quiet passages and
•
is displayed when set to "Midnight", "Evening" or "Day".
loud passages, etc.) by
• If "Dynamic Volume ® " is set to "Yes" in Auto Setup
automatically adjusting to
the setting is automatically changed to "Evening".
the user's preferred volume
setting.
98
AUDIO/VIDEO ADJUST
Setting details
is displayed when set to "ON".
(vpage 23),