Confer Plastics CURVE STEP CCX-AG Assembly, Installation And Use Manual page 5

CONFER CURVE STEP
CONFER CURVE STEP
ADD-ON INSTRUCTIONS
ADD-ON INSTRUCTIONS
The curve add-on can only be installed on the right side
The curve add-on can only be installed on the right side of the step as you
are facing it. The add-on requires an additional 30 lbs. of sand. of the step as you are facing it. The add-on requires
an additional 30 lbs. of sand.
Additional Parts for Step Add-On
Additional Parts for Step Add-On
2 - Foot pads [Part H]
2 - Foot pads [Part H]
1 - Add-on panel [Part J]
1 - Add-on panel [Part J]
1 - Short hand rail post [Part K]
1 - Short hand rail post [Part K]
1 - Long hand rail post [Part L]
1 - Long hand rail post [Part L]
1 - Large flex riser [Part M]
1 - Large flex riser [Part M]
1 - Tread support [Part N]
1 - Tread support [Part N]
1 - Large curved tread [Part O]
1 - Large curved tread [Part O]
USE A LITTLE LIQUID SOAP ON TABS TO HELP WITH ASSEMBLY
Step 19
Step 19
Install the add-on panel [J]
Install the add-on panel
by inserting the three tabs
[J] by inserting the three
into the three openings
tabs into the three open-
located towards the back
ings located towards the
of step panel [A].
back of step panel [A].
Push the tabs all the
Push the tabs all the
way in, then tap panel
way in, then tap panel
down with a
down with a
rubber mallet
rubber mallet
until seated
until seated
in openings.
in openings.
Step 21
Step 21
Tilt the step back far
Tilt the step back
enough to slide the
far enough to slide
end of large flex riser
the end of large flex
[M] up into the slot
riser [M] up into the
located on the front
slot located on the
bottom edge of the
front bottom edge
add-on side panel.
of the add-on side
panel.
Step 23
Step 23
Attach the last foot
pad [H] on to the
Attach the last foot
bottom of the tread
pad [H] on to the
support [N] by placing
bottom of the tread
over the raised tab
support [N] by plac-
and striking with a
ing over the raised
rubber mallet until
tab and striking with
seated. Foot pad [H]
a rubber mallet until
should be installed
seated. Foot pad [H]
in the same position
should be installed in
as the front foot
the same position as
pads on base step.
the front foot pads
on base step.
1 - Medium flex riser [Part P]
1 - Medium flex riser [Part P]
1 - Medium curved tread [Part Q]
1 - Medium curved tread [Part Q]
1 - Small flex riser [Part R]
1 - Small flex riser [Part R]
1 - Small curved tread [Part S]
1 - Small curved tread [Part S]
1 - Tread filler [Part T]
1 - Tread filler [Part T]
1 - Tread extension [Part U]
1 - Tread extension [Part U]
2 - Plugs [WG] (installed in add-on panel)
2 - Plugs [WG]
(installed in add-on panel)
Step 20
Next, install one of the foot pads [H]
onto the tab located on the bottom of
the large flex riser [M] by placing over
the raised tab and striking with a rubber
mallet until seated. Foot pad [H]
should be installed in the same
direction as the
front foot pads
on base step.
[Refer to steps
7 & 9].
Step 22
Insert the tab on
the other end of
the flex riser [M]
into the opening
on side panel [A].
Step 24
Locate the notch on
the bottom edge of
the large flex riser
[M]. Slide the step
support [N] under
then rotate up making
sure part is in notch.
U
Step 20
Next, install one of the foot pads [H]
onto the tab located on the bottom of
the large flex riser [M] by placing over
the raised tab and striking with a rub-
ber mallet until seated. Foot pad [H]
should be installed in the same
direction as the
front foot pads
on base step.
[Refer to steps
7 & 9].
Step 22
Insert the tab on
the other end of
the flex riser [M]
into the opening
on side panel [A].
Step 24
Locate the notch on
the bottom edge of
the large flex riser
[M]. Slide the step
support [N] under
then rotate up mak-
ing sure part is in
notch.
L
T
S
K
J
R
Q
P
O
M
H
N
5
5