Accessories And Replacement Parts; What If There Are Problems - Beurer LB 88 Instructions For Use Manual

• Use a mild cleaning product or a citric acid or vine-
gar-based solution.
• Clean the thread of the screwed plug using the brush.
• Fill the water tank halfway with water.
• Tightly close the water tank using the screwed plug.
• Shake the water tank by rocking it back and forth several
times.
• Empty out the water completely.
• Repeat the process using clean, fresh water.
Clean the air humidifier inside and out
• Empty the water from the base unit via the side edge.
• Wipe the air humidifier with a damp cloth inside and out.
Use only a mild detergent or citric acid or vinegar-based soluti-
on to perform cleaning or disinfection work.
Descaling
Descaling the ultrasound membrane
Hard water can cause limescale to build up in the device and
especially on the ultrasound membrane. This forms white de-
posits. Descale the device regularly.
• Drop some descaling solution onto the ultrasound mem-
brane.
• Leave it to take e ect for two to five minutes.
• Clean the ultrasound membrane using the cleaning brush.
• Rinse the base unit twice with clean, fresh water.
Cleaning inside the base unit
• Dip a damp, soft cloth briefly in descaling solution.
• Use the cloth to wipe the inside of the base unit.
• Carefully pour some clean, fresh water into the base unit.
• Empty the water from the base unit via the side edge.
• Repeat the process using clean, fresh water.
Descaling the water tank
• Half-fill the water tank with descaling solution.
• Tightly close the water tank using the screwed plug.
• Shake the water tank by rocking it back and forth several
times.
• Empty the descaling solution completely.
• Rinse the base unit twice with clean, fresh water.
• Repeat this procedure if necessary.
Storage
If you do not plan to use the device for a relatively long period
of time, we recommend that you thoroughly empty, clean and
dry the device and store it in the original packing in a dry envi-
ronment, ensuring it is not weighed down by additional items.
9. ACCESSORIES AND REPLACEMENT
PARTS
TIP!
If the water is hard, we recommend using the optional anti-li-
mescale filter in addition to the anti-lime pads supplied.
• If the anti-limescale filter does not prevent limescale
build-up, or if white deposits form on or in the device,
the anti-limescale filter should be replaced.
• The service life of the anti-limescale filter is around
two to three months at most.
• If the device is not used for a relatively long time, the
anti-limescale filter must be removed from the water
tank and dried out.
Fitting the anti-limescale filter
• Lift the water tank and rotate it.
• Open the screwed plug on the water tank.
• Screw the anti-limescale filter onto the screwed plug on the
inside.
• Tightly seal the water tank using the screwed plug.
Replacement items
For replacement parts and additional items visit www.beurer.
com or contact the corresponding service address in your
country (according to the service address list).
Replacement parts and additional items are also available from
retailers.
Item
10 anti-lime pads
10 aroma pads
Beurer by Taoasis "Vitality" aroma oil
(10 ml)
Anti-limescale filter

10. WHAT IF THERE ARE PROBLEMS?

Problem
The operating
loop does not
light up.
No LED display.
Red LED display.
No mist is pro-
duced.
The mist has a
strange smell.
H
17
Item number
163.141
163.142
681.30
162.843
Cause Solution
The mains cable Connect the plug.
is not plugged in.
The control dial Turn the control dial
is at its minimum clockwise towards
position. the maximum
position.
The mains cable Connect the plug.
is not plugged in.
The control dial Turn the control dial
is at its minimum clockwise towards
position. the maximum
position.
The water level is Fill the water tank.
too low; the water
tank is empty.
The LED display Fill the water tank.
lights up red.
The LED display Connect the plug.
does not light up.
The device is Remove the
new. water tank, turn the
screwed plug and
remove it.
Air the open,
empty water tank in
a cool, dry place for
twelve hours.
Stale or dirty Empty the base unit
water. and the water tank
and clean them
thoroughly.
Fill the water tank
with fresh water.