Conformance Approvals; Fcc Warning; Appendix A-Hyper Terminal - CyberPower Outlet Series User Manual

CONFORMANCE APPROVALS

FCC Warning

WARNING!! Changes or modifications to this unit
not expressly approved by the party responsible for
compliance could void the user's authority to operate the
equipment.
WARNING!! This equipment has been tested and found
to comply with the limits for a Class A Digital Device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful
interference in residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to
radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or
television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
- Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV
technician for help.
Notice: (1) An unshielded-type power cord is required
in order to meet FCC emission limits and also to prevent
interference to the nearby radio and television reception.
It is essential that only the supplied power cord by used.
(2) Use only shielded cables to connect I/O devices to this
equipment.
Note: THE MANUFACTURER IS NOT RESPONSIBLE
FOR ANY RADIO OR TV INTERFERENCE CAUSED BY
UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT.
SUCH MODIFICATIONS COULD VOID THE USER'S
AUTHORITY TO OPERATE THE EQUIPMENT.
The Class A digital apparatus meets all requirements of the
Canadian Interference-Causing Equipment Regulation.
Cet appareil numerique de la class A respecte toutes les
exigencies du Reglement sur le materiel brouilleur du
Canada.
European Union
This is a class A product. In a domestic environment this
product may cause radio interference in which case the
user may be required to take adequate measures.
CUSTOMER SERVICE & WARRANTY
Product Registration
Thank you for purchasing a CyberPower product.
Prompt product registration entitles coverage under the
Limited Warranty and also allows the opportunity to be
notified of product enhancements, upgrades, and other
announcements.
Registration is quick and easy at www.cyberpowersystems.
com/registration (for USA and Canada) or
www.cyberpower.com/registration (for all other regions).

APPENDIX A-HYPER TERMINAL

Hyper Terminal software can be used for basic PDU
configuration. In order for Hyper Terminal to interact with
the PDU, the PC/server must be connected directly to the
PDU via the serial port with the included RJ45/DB9 serial
port connection cable. It utilizes a textbased interface and
menu system. Navigation through the interface is done by
typing the number of the menu option and pressing the
Enter key. Setup the COM port settings using the following
values.
• Bits per second: 9600
• Data bits: 8
• Parity: None
• Stop bits: 1
• Flow control: None
Note: The session will timeout and logout after 3 minutes
of inactivity. Menu options are shown below:
[Main Menu]
1. Outlet Manager (Switched PDU Series Only)
2. Network Settings
3. System Configuration
4. Account Settings
5. Configure System to Default
6. Logout
[Outlet Manager]
1. Outlet Control
2. Outlet Configuration
[Network Setting]
Physical MAC Address: 00-0C-15-40-08-A9
1. System IP: 192.168.24.20
2. Subnet Mask: 255.255.255.0
3. Default Gateway: 192.168.24.254
4. DHCP: Enabled
5. Http Port: 80
6. Http Access: Enabled
[System Configuration]
1. Date (mm/dd/yyyy) : 11/11/2011
2. Time (hh:mm:ss): 17:17:25
3. Name:PDU20SW8FNET
4. Contact: Administrator
5. Location: Server Room
[Account Setting]
1. Administrator
2. Viewer (Web Only)
[Configure System to Default]
Sure to Configure System to Default
1. Yes
2. No
31