Table of Contents
Advertisement
Quick Links
Installation Manual
MULTI FUNCTION DISPLAY
TZT22X/TZT24X
Model
SAFETY INSTRUCTIONS ................................................................................................ i
SYSTEM CONFIGURATION ........................................................................................... ii
EQUIPMENT LISTS........................................................................................................ iv
1. MOUNTING..............................................................................................................1-1
1.1 Installation of Multi Function Display..................................................................................1-1
1.2 Flush Mounting ..................................................................................................................1-2
2. WIRING....................................................................................................................2-1
2.1 Interface Connections (rear of the unit) .............................................................................2-1
2.2 Power Cable ......................................................................................................................2-2
2.3 MULTI Cable......................................................................................................................2-2
2.4 DRS Radar Sensor Connections .......................................................................................2-3
2.5 Network Connection with Other TZT Series Units .............................................................2-4
2.6 NMEA 2000 Connector ......................................................................................................2-4
2.7 Example TZT22X/24X System Configuration ....................................................................2-8
3. HOW TO SET UP THE EQUIPMENT......................................................................3-1
3.1 How to Set Time Zone, Time Format and Language.........................................................3-3
3.2 How to Set Units of Measurement .....................................................................................3-4
3.3 Initial Setup ........................................................................................................................3-5
3.4 How to Set Up the Radar .................................................................................................3-11
3.5 How to Set Up the Fish Finder.........................................................................................3-14
3.6 Wireless LAN Setting .......................................................................................................3-19
3.7 Ferry Mode.......................................................................................................................3-20
3.8 How to Manage Your Charts............................................................................................3-20
3.9 IP Camera Setup .............................................................................................................3-22
PACKING LIST(S) ....................................................................................................... A-1
OUTLINE DRAWING(S) .............................................................................................. D-1
INTERCONNECTION DIAGRAM(S) ........................................................................... S-1
www.furuno.com
All brand and product names are trademarks, registered trademarks or service marks of their respective holders.
Advertisement
Table of Contents
Related Manuals for Furuno TZtouchXL TZT22X
Summary of Contents for Furuno TZtouchXL TZT22X
-
Page 1: Table Of Contents
3.8 How to Manage Your Charts....................3-20 3.9 IP Camera Setup ......................3-22 PACKING LIST(S) ....................... A-1 OUTLINE DRAWING(S) ....................D-1 INTERCONNECTION DIAGRAM(S) ................S-1 www.furuno.com All brand and product names are trademarks, registered trademarks or service marks of their respective holders. - Page 2 ・FURUNO Authorized Distributor/Dealer 9-52 Ashihara-cho, Nishinomiya, 662-8580, JAPAN A : AUG 2023 Printed in Japan All rights reserved. B : JAN . 24, 2024 Pub. No. IME-45240-B (TEHI ) TZT24X/TZT22X 0 0 0 2 0 0 1 4 3 1 1...
-
Page 3: Safety Instructions
SAFETY INSTRUCTIONS Indicates a potentially hazardous situation which, if not WARNING avoided, could result in death or serious injury. Indicates a potentially hazardous situation which, if not CAUTION avoided, may result in minor or moderate injury. (Examples of symbols) Warning, Caution Prohibitive Action Mandatory Action WARNING... -
Page 4: System Configuration
: Use a commercially available PoE hub. The NETGEAR GS108PE has tested as compatible. The basic functions of the hub were verified, however the compatibility of all functions were not checked. FURUNO cannot guarantee proper operation. Available when FUSION-Link compatible equipment is connected via Ethernet. - Page 5 SYSTEM CONFIGURATION TZT series network connections The TZT series can be connected on the same network in the following combinations. TZtouch: TZtouch2: TZtouch2: TZtouch3: TZT9/14/BB TZTL12F/15F TZT2BB TZT9F/12F/16F/19F TZtouchXL: TZT22X/24X : Version 9.70 or later : Version 3.70 or later...
-
Page 6: Equipment Lists
EQUIPMENT LISTS Standard supply Name Type Code No. Remarks Multi Function Display TZT22X Including installation materi- als, accessories and spare parts. TZT24X Optional supply Name Type Code No. Remarks NMEA Data Converter IF-NMEA2K2 000-020-510 Remote Control Unit MCU-005 000-035-097 MCU-006 000-042-803 MCU-006H 000-042-804... -
Page 7: Mounting
MOUNTING Installation of Multi Function Display The TZT22X/24X is designed to be mounted in a console or panel. The installer of this equipment must read and follow the descriptions in this manual. Wrong installation or improper maintenance can void the warranty. 1.1.1 Mounting considerations When selecting a mounting location for TZT22X/24X, keep the following in mind:... -
Page 8: Flush Mounting
1. MOUNTING Flush Mounting Referring to the figure below, select a flat mounting location. Read the installation in- structions before starting. Pay particular attention to the notes; failure to follow these instructions may cause damage to the unit. Note: Ensure the mounting location is flat, with no indents or protrusions, to allow a secure fit. - Page 9 1. MOUNTING 5. Set the TZT22X/24X to the cutout made at step 1. For installations using the mounting plate, the screws fitted at step 4 should align with the gaps in the unit. Note 1: Cables not shown in figure for simplification. Note 2: Take care not to pinch the cables when fitting the unit.
- Page 10 1. MOUNTING How to remove the cosmetic plates Remove the top and bottom cosmetic plates from the front of the unit. Use a flat-head screwdriver. Starting at one end of the cosmetic plate, insert the blade of the screwdriver into each of the release points (indicated with gray arrows in the fig- ure below), then gently twist the screwdriver until a “pop”...
-
Page 11: Wiring
WIRING Interface Connections (rear of the unit) HDMI IN HDMI IN HDMI OUT HDMI OUT USB1 USB1 MULTI MULTI Rear of the unit NMEA2000 NMEA2000 USB2 USB2 NETWORK NETWORK POWER POWER Analog video input The TZT22X/24X can use regular analog video inputs (PAL or NTSC) that connect to the TZT22X/24X directly via the Video In connector on the MULTI cable (connected to the MULTI port). -
Page 12: Power Cable
2. WIRING NMEA2000 (CAN bus) port TZT22X/24X can be connected to multiple compatible NavNet TZT units using a micro type NMEA 2000 connector. In that case, connect them all to the same network back- bone cable (Refer to section 2.6 for details). MULTI port You can connect to external devices such as buzzers and event switches. -
Page 13: Drs Radar Sensor Connections
How to set up NMEA 0183 data output Note: To set up data input from NMEA 0183 equipment, see "NMEA 0183 equipment data input" on page 2-4. 1. Tap the [FURUNO] icon ( ) to show the home screen and display mode settings. -
Page 14: Network Connection With Other Tzt Series Units
All the NMEA 2000 devices can be incorporat- ed into the NMEA 2000 network. For detailed information about NMEA 2000 wiring, see "FURUNO CAN bus Network Design Guide" (Type: TIE-00170). 2.6.1 How to connect the NavNet TZtouchXL to NMEA 2000 equip- ment Below is an example of two units, connected to NMEA 2000 sensors via the network. - Page 15 2. WIRING To connect NMEA 0183 equipment to TZT22X/24X, use the NMEA 2000 network via the optional NMEA data converter IF-NMEA2K2 (or IF-NMEA2K1). This NMEA connection can accept a baud rate of 4800 or 38400. Heading input to TZT22X/24X allows functions such as Radar Overlay and course sta- bilization (North up, etc.) in the radar operating modes.
- Page 16 2. WIRING Description 129029 GNSS Position Data 129033 Local Time Offset 129038 AIS Class A Position Report 129039 AIS Class B Position Report 129040 AIS Class B Extended Position Report 129041 AIS Aids to Navigation (AtoN) Report 129291 Set &Drift, Rapid Update 129538 GNSS Control Status 129540...
- Page 17 2. WIRING Description Output cycle (msec) 127250 Vessel Heading 127251 Rate of Turn 127257 Attitude 1000 127258 Magnetic Variation 1000 128259 Speed 1000 128267 Water Depth 1000 128275 Distance Log 1000 129025 Position, Rapid Update 129026 COG &SOG, Rapid Update 129029 GNSS Position Data 1000...
-
Page 18: Example Tzt22X/24X System Configuration
2. WIRING Example TZT22X/24X System Configuration Mid/Large-size vessels (External GPS, Radar) This is a single station chart plotter/radar installation. Refer to "SYSTEM CONFIGURATION" on page ii for more details. Radar Sensor Radar Sensor DRS6A X-Class/DRS12A X-Class/ DRS4D X-Class/DRS4DL+/ DRS25A X-Class/DRS6A-NXT/ DRS2D-NXT/DRS4D-NXT DRS12A-NXT/DRS25A-NXT 12 to 24 VDC... -
Page 19: How To Set Up The Equipment
(power switch) to turn the power on. 2. After the startup process completes, the last used display appears and a warning message is displayed. Read the message, then tap [OK]. 3. Tap the [FURUNO] icon ( ) to show the home screen and display mode settings. - Page 20 3. HOW TO SET UP THE EQUIPMENT 5. Drag the menu to show [Initial Setup], then tap [Initial Setup]. Back icon Close Menu title Preview screen Preview screen Menu Menu Changes made in the Changes made in the items items menu can be menu can be previewed here...
-
Page 21: How To Set Time Zone, Time Format And Language
Before setting up your equipment, select the time zone, language and units to use on your equipment as shown below. 1. Tap the [FURUNO] icon to show the home screen and display mode settings. 2. Tap [Settings] to show the [Settings] menu. -
Page 22: How To Set Units Of Measurement
3. HOW TO SET UP THE EQUIPMENT How to Set Units of Measurement 1. Tap the [FURUNO] icon to show the home screen and display mode settings. 2. Tap [Settings] to show the [Settings] menu. 3. Drag the main menu to display [Units], then tap [Units]. -
Page 23: Initial Setup
Note: Some units are set to metric in this section, actual setting ranges vary depending on the unit of measurement set in the [Units] menu. 1. Tap the [FURUNO] icon to show the home screen and display mode settings. 2. Tap [Settings] to show the [Settings] menu. - Page 24 Select the source for each data to input to the system. If two or more sources are connected for a data, select one using the pull-down dialog box. The FURUNO products are shown at the upper part of the list. [Sensor List] Show the information for sensors connected to your equipment.
- Page 25 3. HOW TO SET UP THE EQUIPMENT [GPS Position] section Menu item Description Options (setting range) [Longitudinal (from 0 (m) to 999 (m) Referring to the figure on the bow] right, enter the GPS antenna [Lateral (-Port)] -99 (m) to +99 (m) positioning bow-stern Origin Origin...
- Page 26 005/-006 connection. Further, the cycling order of displays can be set. See the Operator’s Manual. [Sirius Radio Diag- Check the satellite radio of the FURUNO BBWX SiriusXM weather receiver nostic] for proper operation. See the Operator’s Manual. [Sirius Weather Diag-...
- Page 27 3. HOW TO SET UP THE EQUIPMENT Menu Item Description Options (setting range) [Maximum Wind Speed] Set the transducer’s maximum detectable 1 (kn) to 99 (kn) speed. [Graphic Instruments Setup] - [Depth] Menu Item Description Options (setting range) [Minimum Depth] Set the transducer’s minimum detectable 1 (m) to 1999 (m) depth.
- Page 28 3. HOW TO SET UP THE EQUIPMENT [Engine & Tank Manual Setup] section The manual set up method should only be used if the automatic setup did not correctly detect your engines or tanks. Menu Item Description Options (setting range) [Nickname] Change the nickname for the engine or tank.
-
Page 29: How To Set Up The Radar
3. HOW TO SET UP THE EQUIPMENT How to Set Up the Radar 1. Tap the [FURUNO] icon to show the home screen and display mode settings. 2. Tap [Radar] from the [Settings] menu. 3. Tap [User Settings], [Radar Source] then tap appropriate radar source. - Page 30 3. HOW TO SET UP THE EQUIPMENT Menu item Description Options (setting range) [Tuning Source] Select a display in the dual range display to [Range1], [Range2] manually tune. Not available (grayed out) with DRS2D- NXT/DRS4D-NXT/DRS6A-NXT/DRS12A- NXT/DRS25A-NXT. [Manual Tuning] Manually tune the radar. [-50] to [50] Not available (grayed out) with DRS2D- NXT/DRS4D-NXT/DRS6A-NXT/DRS12A-...
- Page 31 Zoom out Radar indications 2. Turn the vessel’s bow toward a target. 3. Tap the [FURUNO] icon to show the home screen and display mode settings. 4. Tap [Settings], [Radar], [Radar Initial Setup]. 5. Tap [Antenna Heading Align]. 6. Key in an offset value (setting range: -179.9° to +180°) that puts the target at the very top of the screen, then tap the icon.
-
Page 32: How To Set Up The Fish Finder
Note 3: In the following tables, the term “Shown with connection of...” means network connection. 1. Tap the [FURUNO] icon to show the home screen and display mode settings. 2. Tap [Settings], then tap [Fish Finder] 3. Tap [User Settings]. [Fish Finder Source], then select fish finder source. - Page 33 3. HOW TO SET UP THE EQUIPMENT Options Menu item Description (setting range) [Transmission Set the TX power level. See the operator’s manual for de- DFF1-UHD: [Off], Power Mode] tails. [Min], [Auto] DFF3-UHD: 0 to [External KP] Select on to synchronize with external sounder’s keying [OFF], [ON] pulse.
- Page 34 Note 3: When the DI-FFAMP is connected and [Transducer Setup Type] menu is set to [Manual], the message “Power amplifier unit detected: In order to manually adjust your transducer setup, please contact your Furuno dealer.” appears. Contact your FURUNO dealer for setup.
- Page 35 3. HOW TO SET UP THE EQUIPMENT When [Transducer Setup Type] is set to [Model] and connected to DFF3-UHD Menu item Description Options (setting range) [TX Mode HF] Band adjustment mode for center [Auto CHIRP], [FM (Manual frequency and CHIRP frequency of CHIRP)] , [CW (Fixed Frequen- the transducer connected to the...
- Page 36 3. HOW TO SET UP THE EQUIPMENT When [Transducer Setup Type] is set to [Manual] and connected to DFF3-UHD Menu item Description [TX Volt HF] Not available (grayed out). [TX Volt LF] Not available (grayed out). [High Frequency] Set the frequency (kHz) of the transducer connected to the high frequency side. [Low Frequency] Set the frequency (kHz) of the transducer connected to the low frequency side.
-
Page 37: Wireless Lan Setting
How to join an existing wireless network By connecting to an existing network, you may download software updates and weather information from the Internet. 1. Tap the [FURUNO] icon ( ) to show the home screen and display mode settings. -
Page 38: Ferry Mode
How to create a wireless LAN network Smart devices connected to this wireless network may also connect directly to the unit, allowing use of the TZT22X/24X applications. 1. Tap the [FURUNO] icon ( ) to show to show the home screen and display mode settings. - Page 39 ([Chart Master Device] setting: [OFF]) or vice versa, you must reacquire an unlock code. 3.8.1 How to view your charts Tap the [FURUNO] icon to show the home screen, then tap [Charts], [MM3D Charts Catalog] to display your charts catalog. Tap to dowload chart unlock codes.
-
Page 40: Ip Camera Setup
3.8.2 How to update or add charts Free (USA and NOAA) and for-fee compatible charts are provided by FURUNO and Mapmedia. Go to the URL shown below to download Mapmedia charts. For FURUNO- supplied charts, contact your local FURUNO dealer.