Furuno NavNet TZtouch3 TZT2BB Setup Manual
  1. Manuals
  2. Brands
  3. Furuno Manuals
  4. Marine Equipment
  5. NavNet TZtouch3 Series
  6. Setup manual
Furuno NavNet TZtouch3 TZT2BB Setup Manual

Furuno NavNet TZtouch3 TZT2BB Setup Manual

Hide thumbs Also See for NavNet TZtouch3 TZT2BB:
Table of Contents

Advertisement

Quick Links

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the NavNet TZtouch3 TZT2BB and is the answer not in the manual?

Questions and answers

Related Manuals for Furuno NavNet TZtouch3 TZT2BB

Summary of Contents for Furuno NavNet TZtouch3 TZT2BB

  • Page 2: Table Of Contents

    Omnisense Ulysses/Ulysses Mini Camera Setup Instructions for TZT2BB and TZtouch3 MFDs Table of Contents 1. Typical Omnisense Camera Packing List …………….………………………..……..…………… 2. Prerequisites ……………………………………………………….………………………………...…………. 3. Initial Setup ……………………………………….…………………………………………………………….. 4. Getting Started ………………………………….….……………………..…………………………………… 5. Omnisense Camera Setup ……………………………………………………………..………….…………… 6. Setting Up Omnisense Controller …………………………….……………………………...………………..

  • Page 3: Typical Omnisense Camera Packing List

    1. Omnisense Packing List Omnisense Camera Camera Remote Controller Camera Junction Box 10m Combo Power/Network Cable 1m Controller Power Cable 2m Controller Network Cable 1.5m Analog Video Cable Mounting Hardware User Manual and Installation Templates...

  • Page 4: Prerequisites

    2. Prerequisites 1. Furuno NavNet TZtouch3 with software version 2 or higher (TZT2BB requires v8.01 or higher) 2. Omnisense camera 3. RJ4-5CN-STR (RJ45 Female-Female coupler) for connection of the TZT3 to Omnisense Junction Box 4. 4MM Allen to open Omnisense junction box 5.

  • Page 5: Getting Started

    4. Getting Started Notes: Prior to powering up the Omnisense camera, please ensure it is securely mounted as the • camera will move during its boot up sequence. If at any time during the camera setup you are prompted for a Login and Password, Login is Admin and •...
  • Page 6 3. Using the joystick, scroll over to Device Access to view the page below. Using the joystick, select Furuno and press the Enter button ,then use the joystick to highlight Save and Reboot, then press the Enter button .Choose “OK” when prompted to continue. Allow the camera system time to reboot.
  • Page 7 11. From the Home screen, tap on the (+) box to add a new page. 12. Drag Omnisense camera icon over to create a new camera page and tap on Green Check Mark. 13. TZtouch3 will now open to Omisense camera page you will now have control over the camera. Note: Tap screen to get camera control circle to appear.

  • Page 8: Setting Up Omnisense Controller

    6. Setting Up Omnisense Controller 1. Tap on the TZtouch3 screen to bring up Omnisense Menu. Tap on the Menu Icon. 2. Tap on the Settings Icon.
  • Page 9 3. Swipe from right to left on the top menu bar until the Controller page is selected, then tap on Scan. 4. Omnisense Controller will appear under Controller S/N box. Tap the (+) to add your controller to the network. Note: Controller serial number will grey out when + is...
  • Page 10 5. Tap Back to return to the previous screen. 6. Tap Set to confirm the new automatically assigned IP address for your controller. 7. Setup is now complete; you may now exit the Omnisense Menu by tapping the Return Icon. 8.

  • Page 11: Final Steps

    7. Final Steps With both devices ON, select the Omnisense camera page. Tap the screen to use the functions of the Omnisense camera.

  • Page 12: Appendix

    Appendix 1. Checking the software version on your TZT3 MFD: [Select Menu]>[Settings]>[Initial Setup]>[Quick Test] to view current program version To find your TZT3 software version during boot up: Press the power button on your TZT3. When you see the screen below, look in the lower right-hand corner and record the last four digits of the number shown.

This manual is also suitable for:

Navnet tztouch3 tztl12fNavnet tztouch3 tzt9f

Table of Contents