Page 1
About the BitStorm 6051 POTS Splitter The BitStorm™ system enables simultaneous high-speed digital data access and analog voice service over the same twisted-pair telephone line. The BitStorm 6051 POTS (plain old telephone service) splitter card separates the DSL (Digital Subscriber Line) and POTS frequencies. It provides service to up to 24 DSL ports.
BitStorm 4800, local loop, and in-building wiring Securing the cables Be sure to register your warranty at www.paradyne.com/warranty. Technical Manuals Document Title BitStorm 4800 User’s Guide BitStorm 4800 Management Module Installation Instructions BitStorm 4800 Installation Guide July 2002 BitStorm DSL 6051-A2-GZ40-10...
Page 3
A flat-blade screwdriver to install the chassis grounding wire. POTS Splitter Card Package Checklist Verify that your POTS splitter card package contains the following: BitStorm 6051 POTS splitter card Plastic bag with three of each item: — Plastic tie-wrap anchors —...
Page 4
POTS Splitter 1-Slot Chassis NOTE: If your 1-slot 5011 POTS splitter chassis is being placed on a tabletop, install the rubber feet as shown above. Discard the rubber feet for a rack-mounted chassis. Placement of Rubber Feet 02-17153 July 2002 6051-A2-GZ40-10...
Page 5
— Six #10-32 x 1/4 Phillips flat-head mounting screws — Four #10-32 x 1/2 Phillips-head mounting screws — Four #12-24 x 1/2 Phillips-head mounting screws — Four #12-24 self-retaining nuts — Four black rubber feet (discard) POTS Splitter 6-Slot Chassis 6051-A2-GZ40-10 Filler Panels July 2002 02-17154...
Page 6
The number of POTS splitters required. The BitStorm 4800 comes in a 24-port and a 48-port model, requiring one or two POTS splitter chassis, respectively. The 48-port BitStorm 4800 and two 6051 POTS splitters are pictured. NOTE: Install chassis in the rack from the bottom up to maintain stability.
Install the appropriate 19 (483 mm) or 23 (584 mm) brackets on the 1-slot or 6-slot chassis. 1-Slot Chassis 6-Slot Chassis Center Mount Front Mount Select one of the next two procedures for chassis installation in a rack. 6051-A2-GZ40-10 19-Inch Rack 23-Inch Rack 99-15486-02 23-Inch Rack 19-Inch Rack 99-15434-02...
Page 8
4. Loosely install the bottom screws first and then the top screws. 5. Tighten all screws firmly using a Phillips screwdriver. Repeat the process for each POTS splitter chassis. POTS splitter chassis can be mounted directly on top of each other. Front Rail Self-Retaining Screw July 2002 00-15436-02 6051-A2-GZ40-10...
Page 9
3. Loosely install the bottom screws first and then the top screws. 4. Tighten all screws firmly with a Phillips screwdriver. Repeat the process for each POTS splitter chassis. POTS splitter chassis can be mounted directly on top of each other. 6051-A2-GZ40-10 Front Rail Screw 99-15435-01...
Then the grounding lug is . . . On the rear of the chassis on the left. On the front of the chassis on the top right. POTS Splitter 6-Slot Chassis July 2002 02-17155 98-15879-01 6051-A2-GZ40-10...
Page 11
2. Slide the POTS splitter card into the chassis. 3. Tighten the quarter-turn fastener on each side of the faceplate of the POTS splitter card. POTS Splitter 6-Slot Chassis 1/4-Turn Fastener DSL Interface 6051-A2-GZ40-10 Filler Panel Loop Interface PSTN Interface 1/4-Turn Fastener July 2002...
Page 12
48-port BitStorm 4800 has two connectors. 2. Connect the Loop interface to the in-building POTS and ADSL CPE. 3. Connect the PSTN interface to the PBX or PSTN. The 48-port BitStorm 4800 and two 6051 POTS splitters are pictured. Splitters in RTS 25-...
Page 13
— If the connector on the cable has a short screw, install the #4-40 jack screw provided into the threaded hole of the connector in the circuit card. Attach the short screw in the cable to the jack screw and tighten. Anchor Mount 6051-A2-GZ40-10 POTS Splitter Card Faceplate Long Screw...
Page 14
3. Tighten the tie wrap and trim the excess. POTS Splitter Card Faceplate 00-15553-01 Repeat the procedure for all the interface cables. POTS Splitter 6-Slot Chassis DSL Interface Loop Interface PSTN Interface 02-17157 July 2002 6051-A2-GZ40-10...
Connector Pin Numbers Pin assignments are the same for all three connectors on the POTS splitter cards. 50-Position Telco Connector POTS Splitter # 6051-A2-GZ40-10 Pin # Ring Pin # Tip July 2002 Pin 1 Pin 25 Pin 26 Pin 50...
Directive 72/72/33C – Council Directive of 19 February 1973 on the harmonization of the laws of the member states relating to electrical equipment designed for use within certain voltage limits, as amended by Directive 93/68EEC. 6051-A2-GZ40-10 ) wire for connection to July 2002...