Page 1
PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. GB510NAS / GB510ANAS INSTALLATION TOOL GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR A DISTRIBUTOR NEAR YOU. GAGE BILT 44766 Centre Court, Clinton Twp., MI. 48038 USA Ph: +1 (586) 226-1500 Fax: +1 (586) 226-1505 MADE in USA solutions1@gagebilt.com / www.gagebilt.com...
Description of Functions ................................5 Warnings ..................................... 6 Principle of Operation ................................7 How to set-up the GB510NAS / GB510ANAS ........................... 8 How to use the GB510NAS / GB510ANAS ..........................9 Maintenance ..................................... 10 Troubleshooting / Relief Valve Installation ..........................11 Overhaul ....................................
GAGE BILT DECLARATION OF CONFORMITY MANUFACTURER: Gage Bilt Inc. 44766 Centre Ct., Clinton Twp., Michigan U.S.A. +1(586-226-1500) WE DECLARE THAT THE EQUIPMENT SPECIFIED HEREIN CONFORMS TO THE FOLLOWING DIRECTIVES AND STANDARDS Machinery Directive 2006/42/EC EN12100-1 & EN12100-2 EN792-1:2000+A1 The Supply of Machinery (Safety) Regulations 2008 EU REPRESENTATIVE Edgar Hausmann GmbH Förster-Busch-Str.
Any other use is forbidden. The GB510NAS and the GB510ANAS are hydraulic installation tools designed specifically for the efficient installation of 5/16” (7.94 mm) NAS Shear, NAS Tension Pull Type lockbolts, C6L® & GP® fasteners. They weigh just over 4 lbs. (1.81 kg) and can be operated in any position.
(such as the deflector, pintail collection bottle or catcher bag). 6. Forcible ejection of the mandrel from the front of the nose assembly is possible. GB510NAS/GB510ANAS INSTALLATION TOOL: S/N 1045 AND ABOVE Rev 9/23 CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS...
When the tool is connected to a powerunit, operation is controlled by a actuator to the hydraulic hoses. The GB510ANAS incorporates an air actuator to send a signal; the GB510NAS an electric actuator. When the button is depressed, a directional valve in the powerunit directs oil to the front side of the piston forcing it and the nose assembly collet rearward.
1. Set hydraulic power unit to the recommended pressure, 5,400 psi. (372.3 bar) - 5,600 psi. (386.1 bar) Max. for the pull and 2,200 (151.7 bar) - 2,400 psi (165.5 bar) Max. for the return. Gage Bilt pressure gage assembly (942280) (Sold Separately) is recommended to aid in this procedure.
Do not operate when recommended pressures are exceeded as it could cause severe personal injury and or damage the equipment. WARNING: Use only Gage Bilt hydraulic hoses and couplings, or equivalent, rated for 10,000 psi. (689.48 bar) working pressure. CAUTION: Do not use beyond the design intent.
WARNING: Tool must be maintained in a safe working condition at all times and examined on a daily basis for damage or wear. Any repair must be done by qualified personnel trained on Gage Bilt procedures. WARNING: Excessive contact with hydraulic oil and lubricants should be avoided.
Position relief valve 4 flats INCORRECT towards REAR of tool. Image may not reflect actual tool GB510NAS/GB510ANAS INSTALLATION TOOL: S/N 1045 AND ABOVE Rev 9/23 CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS...
• Note: Gage Bilt does not recommend using a pneumatic lubricator or adding pneumatic oil to the air inlet on our tools or powerunits. If a tool is performing poorly or leaking, a complete overhaul may be necessary.
Accessories Approved for use on Gage Bilt CE installation tools and/or other manufacturer’s CE approved tools of similar design. (Sold Separately) Grip Gage #GB105093 For NAS LOCKBOLTS and blind fasteners (Sold Separately) Gage Bilt also supplies pin & collar swage inspection gages to certify...
Page 16
Accessories Cont. Approved for use on Gage Bilt CE installation tools and/or other manufacturer’s CE approved tools of similar design. (Sold Separately) GB947 ELECTRIC POWERUNIT (Sold Separately) The GB947 Hydraulic Powerunit is a light-weight, portable power source designed to operate on a wide range of hydraulic installation tools.
Page 17
Accessories Cont. Approved for use on Gage Bilt CE installation tools and/or other manufacturer’s CE approved tools of similar design. (Sold Separately) GB910 HYDRAULIC POWERUNIT (Sold Separately) The GB910 Hydraulic Powerunit is a portable power source designed to operate a wide range of hydraulic installation tools.
Page 18
Accessories Cont. Approved for use on Gage Bilt CE installation tools and/or other manufacturer’s CE approved tools of similar design. (Sold Separately) GB912 / GB912-D HYDRAULIC POWERUNITS (Sold Separately) GB912 HYDRAULIC POWERUNIT GB912-D HYDRAULIC POWERUNIT The GB912 Hydraulic Powerunit is a portable power source designed to operate a wide range of hydraulic installation tools.
Page 19
This page intentionally left blank GB510NAS/GB510ANAS INSTALLATION TOOL: S/N 1045 AND ABOVE Rev 9/23 CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS...
Page 20
Riveter Kits Available (Sold Separately) Gage Bilt offers a wide selection of standard and custom kits tailored to your needs. Contact us for more information. Approved TEFLON® IS REGISTERED TRADEMARK OF E.I. DUPONT DE NEMOURS & CO. LUBRIPLATE® IS A REGISTERED TRADEMARK OF FISKE BROTHERS REFINING CO. SLIC-TITE® IS A REGISTERED TRADEMARK OF LA-CO INDUSTRIES INC.