Gage Bilt GB703VT Original Instructions Manual
  1. Manuals
  2. Brands
  3. Gage Bilt Manuals
  4. Rivet Tools
  5. GB703VT
  6. Original instructions manual

Gage Bilt GB703VT Original Instructions Manual

Hide thumbs Also See for GB703VT:
Table of Contents

Advertisement

Quick Links

Download this manual
ORIGINAL INSTRUCTIONS
S/N: 3158 AND ABOVE
PLEASE CONTACT GAGE BILT FOR
ALL OTHER SERIAL NUMBERS.
GB703VT
INSTALLATION TOOL
GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE
E-MAIL US FOR A DISTRIBUTOR NEAR YOU.
GAGE BILT
44766 Centre Court, Clinton Twp., MI. 48038 USA
Ph: +1 (586) 226-1500 Fax: +1 (586) 226-1505
MADE in USA
solutions@gagebilt.com / www.gagebilt.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GB703VT and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Gage Bilt GB703VT

Summary of Contents for Gage Bilt GB703VT

  • Page 1 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. GB703VT INSTALLATION TOOL GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR A DISTRIBUTOR NEAR YOU. GAGE BILT 44766 Centre Court, Clinton Twp., MI. 48038 USA Ph: +1 (586) 226-1500 Fax: +1 (586) 226-1505 MADE in USA solutions@gagebilt.com / www.gagebilt.com...

  • Page 2: Table Of Contents

    Parts Lists ....................................16 DEXRON® III Oil Safety Data Sheet (SDS) ..........................17 How to Assemble Vacuum ..............................18 Nose Assembly selection chart .............................. 19 Accessories ..................................20-24 S/N: 3158 AND ABOVE Rev. 5/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 3: Eu Conformity And Warranty

    GAGE BILT DECLARATION OF CONFORMITY MANUFACTURER: Gage Bilt Inc. 44766 Centre Ct. Clinton Twp. Michigan +1(586-226-1500) WE DECLARE THAT THE EQUIPMENT SPECIFIED HEREIN CONFORMS TO THE FOLLOWING DIRECTIVES AND STANDARDS Machinery Directive 2006/42/EC EN12100-1 & EN12100-2 EN792-1:2000+A1 EU REPRESENTATIVE Edgar Hausmann GmbH Förster-Busch-Str. 10 D-34346 Hann. Münden Germany EQUIPMENT DESCRIPTION: GB703VT FASTENER INSTALLATION TOOL This product specified above conforms to the above dIrectives and standards.

  • Page 4: Description And Technical Specifications

    90 psi (6.2 bar) air pressure at the air inlet. The GB703VT installation tool operates on 90 to 100 psi (6.2-6.9 bar) of air pressure, providing the maximum efficiency. At 90 lbs. (6.2 bar) of air pressure, the GB703VT does not exceed 81.5 dB (A) and consumes .16 SCF/cycle (4.53 L/cycle).

  • Page 5: Description Of Functions

    DESCRIPTION OF FUNCTIONS Hanger Nose Assembly Head Cylinder Pintail Evacuation Tube Actuator Assembly – Air Actuator Lever Assembly Handle Air Inlet Vacuum Assembly S/N: 3158 AND ABOVE Rev. 5/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 6: Safety Warnings

    4. Support the weight of the tool in a stand, tensioner or balancer, because a lighter grip can then be used to support the tool. S/N: 3158 AND ABOVE Rev. 5/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 7: Principle Of Operation

    Air Piston moves up Air Piston moves down Air exhaust Air exhaust Pressurized Oil Pressurized Air Unpressurized Oil Unpressurized Air Images may not reflect actual tool S/N: 3158 AND ABOVE Rev. 5/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 8: How To Setup The Gb703

    NOSE ASSEMBLY FITTING FASTENER EVACUATION TUBE WORK RED SHIPPING PLUG USER QUICK ACTUATOR DISCONNECT FITTING AIR INLET AIR HOSE Image may not reflect actual tool S/N: 3158 AND ABOVE Rev. 5/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 9: How To Use The Gb703

    Exert firm pressure against fastener during installation. 3. Press actuator to start cycle. 4. Release actuator as soon as fastener breaks. 5. Repeat steps 1-4. S/N: 3158 AND ABOVE Rev. 5/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 10: Maintenance

    WARNING: Tool must be maintained in a safe working condition at all times and examined on a daily basis for damage or wear. Any repair must be done by qualified personnel trained on Gage Bilt procedures. WARNING: Excessive contact with hydraulic oil and lubricants must be avoided.

  • Page 11: Filling And Bleeding

    Subtract dimension (B) from dimension (A). If stroke doesn’t check .780" (19.8 mm) min. (See figures below) follow bleeding procedure above until stroke met. For your consideration, Gage Bilt offers a depth gage (Pt.# A-1935) to help simplify and more accurately check your tool stroke. Please contact Gage Bilt for more information.

  • Page 12: Troubleshooting

    Note: The vacuum regulator may visually appear clean, but still may be contaminated with a thin film, therefore, the steps above should be performed to assure best performance. Image may not reflect actual tool S/N: 3158 AND ABOVE Rev. 5/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 13: Overhaul

    Perform overhaul in a clean, well lit area using care not to scratch or nick any smooth surface that comes in contact with an o'ring. Use of Lubriplate® (Gage Bilt part no. 402723) or other lubricant is recommended during reassembly to prevent tearing or distorting of o'rings.
  • Page 14 Insert and turn 5/8” open end box wrench / adjustable wrench and snug tight approximately 1/4-1/2 turn. Re-install actuator lever assembly (704343) including pin-slotted (400608) to the handle assembly (704132). S/N: 3158 AND ABOVE Rev. 5/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
  • Page 15 (704262) will facilitate the proper installation of the spring (704141). Valve sleeve (703139) can be pulled out using valve sleeve removal tool assembly (704163). S/N: 3158 AND ABOVE Rev. 5/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 16: Parts Lists

    PARTS LIST S/N: 3158 AND ABOVE Rev. 5/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 17: Dexron® Iii Oil Safety Data Sheet (Sds)

    Use material for its intended purpose or recycle if possible. Oil collection services are available for used oil recycling or disposal. Place contaminated materials in containers and dispose of in a manner consistent with applicable regulations. S/N: 3158 AND ABOVE Rev. 5/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 18: How To Assemble Vacuum

    HOW TO ASSEMBLE EVACUATION TUBE / VACUUM (Sold Separately) S/N: 3158 AND ABOVE Rev. 5/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 19: Nose Assembly Selection Chart

    NOSE ASSEMBLY SELECTION CHART (Sold Separately) S/N: 3158 AND ABOVE Rev. 5/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
  • Page 20 Deflector Vacuum SHAV SRAV Bottle Vacuum SHAVT SRAVT Tube Images may not reflect actual tools Tools with hose kits available to 26 ft (7.92 m) S/N: 3158 AND ABOVE Rev. 5/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
  • Page 21 5ft Hyd. Hoses are recommended with use of Backpack Additional custom lengths are available. Split Handle Installation Tool Backpacks For 5ft hose Split System Tools. (Sold Separately) S/N: 3158 AND ABOVE Rev. 5/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 22: Accessories

    GB703VT ACCESSORIES Approved for use on Gage Bilt CE installation tools and/or other manufacturer’s CE approved tools of similar design. (Sold Separately) Air Bleeder Assembly Catcher Bag-Stem #704153 #704214 (Sold Separately) (Sold Separately) Tool Stroke Depth Gage #A-1935 (Sold Separately) Image may not reflect actual gage.
  • Page 23 This page intentionally left blank S/N: 3158 AND ABOVE Rev. 5/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
  • Page 24 Riveter Kits Available (Sold Separately) Gage Bilt offers a wide selection of standard and custom kits tailored to your needs. Contact us for more information. Approved DEXRON® IS A REGISTERED TRADEMARK OF GENERAL MOTORS CORPORATION. LUBRIPLATE® IS A REGISTERED TRADEMARK OF FISKE BROTHERS REFINING. LOCTITE® IS A REGISTERED TRADEMARK OF HENKEL CORPORATION.

Table of Contents