Page 1
PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. GB752SH INSTALLATION TOOL GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR A DISTRIBUTOR NEAR YOU. GAGE BILT 44766 Centre Court, Clinton Twp., MI. 48038 USA Ph: +1 (586) 226-1500 Fax: +1 (586) 226-1505 MADE in USA solutions@gagebilt.com / www.gagebilt.com...
Overhaul ....................................14-16 Parts Lists .................................... 17-18 DEXRON® III Oil Safety Data (SDS) ............................19 Nose Assembly Selection Chart and Accessories ......................20-24 GB752SH INSTALLATION TOOL: S/N# 1144 AND ABOVE REV. 5/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
GAGE BILT DECLARATION OF CONFORMITY MANUFACTURER: Gage Bilt Inc. 44766 Centre Ct. Clinton Twp. Michigan U.S.A. +1(586-226-1500) WE DECLARE THAT THE EQUIPMENT SPECIFIED HEREIN CONFORMS TO THE FOLLOWING DIRECTIVES AND STANDARDS Machinery Directive 2006/42/EC EN12100-1 & 12100-2 EN792-1:2000+A1 EU REPRESENTATIVE Edgar Hausmann GmbH Förster-Busch-Str.
.500” (12.7 mm) fastener setting stroke. The GB752SH split handle installation tool operates on 90 to 100 psi. (6.2-6.9 bar) of air pressure, with 90 psi. (6.2 bar) providing maximum efficiency. At 90 psi. (6.2 bar) of air pressure, the GB752SH does not exceed 81.5 dB(A) and consumes .30 SCF/cycle (8.50 L/cycle).
Bleed Screw Lever Handle Assembly Hydraulic “PULL” Hose Air Line “RETURN” Bleed Screw Handle Assembly Air Inlet Image may not reflect actual tool GB752SH INSTALLATION TOOL: S/N# 1144 AND ABOVE REV. 5/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
4. Support the weight of the tool in a stand, tensioner or balancer, because a lighter grip can then be used to support the tool. GB752SH INSTALLATION TOOL: S/N# 1144 AND ABOVE REV. 5/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
Air Piston moves down Air exhaust Air exhaust Pressurized Oil Pressurized Air Unpressurized Oil Unpressurized Air Images may not reflect actual tool GB752SH INSTALLATION TOOL: S/N# 1144 AND ABOVE REV. 5/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
HEAD CYLINDER DEFLECTOR FASTENER WORK LEVER RED SHIPPING PLUG USER QUICK DISCONNECT FITTING AIR INLET AIR HOSE Image may not reflect actual tool GB752SH INSTALLATION TOOL: S/N# 1144 AND ABOVE REV. 5/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
5. Release lever as soon as fastener breaks. Repeat steps 1-4. 6. Repeat steps 1-5. Images may not reflect actual tool or fastener GB752SH INSTALLATION TOOL: S/N# 1144 AND ABOVE REV. 5/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
WARNING: Tool must be maintained in a safe working condition at all times and examined on a daily basis for damage or wear. Any repair must be done by qualified personnel trained on Gage Bilt procedures. WARNING: Excessive contact with hydraulic oil and lubricants must be avoided.
(703119) facing upward. Top of Handle Assembly Oil passage with o’ring (S832) ***Keep air hole free from oil*** Images may not reflect actual tool. GB752SH INSTALLATION TOOL: S/N# 1144 AND ABOVE REV. 5/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
Subtract dimension (A) from dimension (B). If stroke is not consistent within 1/64" (.396 mm) repeat bleeding procedure until stroke met. For your consideration, Gage Bilt offers a depth gage (Pt.# A-1935) to help simplify and more accurately check your tool stroke.
21 to select Stroke Limiter). Tighten End Cap onto tool. (See pg. 10 for torque setting). Images may not reflect actual tool GB752SH INSTALLATION TOOL: S/N# 1144 AND ABOVE REV. 5/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
Perform overhaul in a clean, well lit area using care not to scratch or nick any smooth surface that comes in contact with an o'ring. Use of Lubriplate® (Gage Bilt part no. 402723) or other lubricant is recommended during reassembly to prevent tearing or distorting of o'rings.
Page 15
Reinsert pin (703543) into hole on handle assembly (700343). Re-attach the lever (704345) and tighten set screw (401771). Note: View above shows proper orientation of lever. GB752SH INSTALLATION TOOL: S/N# 1144 AND ABOVE REV. 5/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
Page 16
Valve spring installation tool (744251) will facilitate the proper installation of the spring (744144). Valve sleeve (743144) can be pulled out using valve sleeve removal tool (744152). GB752SH INSTALLATION TOOL: S/N# 1144 AND ABOVE REV. 5/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
Use material for its intended purpose or recycle if possible. Oil collection services are available for used oil recycling or disposal. Place contaminated materials in containers and dispose of in a manner consistent with applicable regulations. GB752SH INSTALLATION TOOL: S/N# 1144 AND ABOVE REV. 5/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
GB752SH ACCESSORIES Approved for use on Gage Bilt CE installation tools and/or other manufacturer’s CE approved tools of similar design. (Sold Separately) NOSE ASSEMBLY SELECTION CHART STRAIGHT RIGHT ANGLE OFFSET (Sold Separately) (Sold Separately) (Sold Separately) FASTENER DIA. STRAIGHT *RIGHT ANGLE...
Page 21
Accessories Cont. Approved for use on Gage Bilt CE installation tools and/or other manufacturer’s CE approved tools of similar design. (Sold Separately) Adapter Assembly Adapter Assembly 730715 751204 Adapts GB715 Series Nose Assemblies to: Adapts 204 offset series nose assemblies Gage Bilt GB752, GB730, GB713, GB731 &...
Page 22
Hand held weight - 2.00 lbs. (.9 kg) Entire tool weight - 7.00 lbs. (3.2 kg) Pull load - 3,800 lbs.(16.9 kN) GB752SH INSTALLATION TOOL: S/N# 1144 AND ABOVE REV. 5/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
Page 23
This page intentionally left blank GB752SH INSTALLATION TOOL: S/N# 1144 AND ABOVE REV. 5/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
Page 24
Riveter Kits Available (Sold Separately) Gage Bilt offers a wide selection of standard and custom kits tailored to your needs. Contact us for more information. Approved Approved Split Riveter Tool Backpacks For 5ft hose Split System Tools. (Sold Separately) DEXRON® IS A REGISTERED TRADEMARK OF GENERAL MOTORS CORPORATION. LOCTITE® IS A REGISTERED TRADEMARK OF HENKEL CORPORATION. LUBRIPLATE® IS A REGISTERED TRADE- MARK OF FISKE BROTHERS REFINING CO.