1. Manuals
  2. Brands
  3. Gage Bilt Manuals
  4. Rivet Tools
  5. GB731
  6. Installation tool

Gage Bilt GB731 Installation Tool

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
S/N: 1702 AND ABOVE
GB731
PLEASE CONTACT GAGE BILT FOR
ALL OTHER SERIAL NUMBERS.
INSTALLATION TOOL
GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE
E-MAIL US FOR A DISTRIBUTOR NEAR YOU.
GAGE BILT Inc.
GAGE BILT
44766 Centre Court
(586) 226-1500
Clinton Twp. MI 48038
(586) 226-1505 Fax
MADE IN U.S.A.
e-mail: solutions@gagebilt.com / www.gagebilt.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GB731 and is the answer not in the manual?

Questions and answers

Related Manuals for Gage Bilt GB731

Summary of Contents for Gage Bilt GB731

  • Page 1 S/N: 1702 AND ABOVE GB731 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. INSTALLATION TOOL GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR A DISTRIBUTOR NEAR YOU. GAGE BILT Inc. GAGE BILT 44766 Centre Court (586) 226-1500 Clinton Twp. MI 48038 (586) 226-1505 Fax MADE IN U.S.A.

  • Page 2: Table Of Contents

    - .600" (15.24 mm) Rated pull load - 4,800 lbs. (21.35 kN) Noise level - 81.5 dB (A) Vibration - Tested– No Hazards Found. GB731 S/N: 1702 AND ABOVE REV. 3/15 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 3: Warnings

    It is recommended operator wear a suitable glove WARNING during operation where prolonged use is expected. Air pressure not to exceed 100 psi (6.9 bar). GB731 S/N: 1702 AND ABOVE REV. 3/15 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 4: Principle Of Operation

    (1). This action generates a return force on the nose assembly pushing it off the installed fastener. Image may not reflect actual tool GB731 S/N: 1702 AND ABOVE REV. 3/15 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 5: How To Use The Gb731

    (704343), the stem will eject to the rear of the tool. WARNING: Always disconnect air supply when tool is not in use to prevent accidental start-up. Image may not reflect actual tool GB731 S/N: 1702 AND ABOVE REV. 3/15 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 6: Description And Maintenance

    4800 lbs. (21.35 kN) with 90 psi (6.2 bar) air pressure at the air inlet. The GB731 riveter operates on a wide range of air pressure, with 90 to 100 psi (6.2-6.9 bar) providing the maximum efficiency. At 90 psi.

  • Page 7: Filling And Bleeding

    (A). Holding actuator lever assy (704343) in, check dimension (B). Subtract dimension (A) from dimension (B). If stroke is not consistent within 1/64" (.0156) repeat steps 6-16. (731010 Sold Separately) GB731 S/N: 1702 AND ABOVE REV. 3/15 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 8: Troubleshooting

    Replace worn or broken parts. Clean the surface the jaws ride on. Stems lodged side by side in the follower. Disassemble, remove stems, and reassemble. Incorrect follower. GB731 S/N: 1702 AND ABOVE REV. 3/15 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 9: Overhaul

    WARNING: Tool must be maintained in a safe working condition at all times and examined on a daily basis for damage or wear. Any repair should be done by qualified personnel trained on Gage Bilt procedures. WARNING: When operating, repairing or overhauling tool, wear approved eye protection. Do not look in Front of tool or rear of tool when installing fastener.

  • Page 10: Parts Lists

    (A-928) uniformly to 40 inch lbs. to prevent leakage around the gasket (704129). PISTON ROD ASSY (731333) 731134 - BACK-UP RING (2 REQ'D) 731139 - SCREW- PISTON ROD CAP GB731 S/N: 1702 AND ABOVE REV. 3/15 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
  • Page 11 NOTE: Valve spring (704162) tool will facilitate the proper installation of the spring (704141), valve sleeve (703139) can be pulled out using valve sleeve removal tool (704163). GB731 S/N: 1702 AND ABOVE REV. 3/15 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 12: Dexron® Iii Oil Safety Data

    Use material for its intended purpose or recycle if possible. Oil collection services are available for used oil recycling or disposal. Place contaminated materials in containers and dispose of in a manner consistent with applicable regulations. GB731 S/N: 1702 AND ABOVE REV. 3/15 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 13: Nose Assembly Selection Chart

    A SP ®, LGP ®, A ND GP ® A RE REGISTERED TRA DEM A RKS OF A LCOA INC. CHERRYM A X® A ND M B C® A RE REGISTERED TRA DEM A RKS OF CHERRY A EROSP A CE FA STENERS. GAGE BILT CERTIFIES THE GB731 WILL INSTALL THE ABOVE FASTENERS **ALL OFFSET 204 SERIES NOSES REQUIRE 751204 ADAPTER.

  • Page 14: Eu Conformity And Warranty

    GAGE BILT DECLARATION OF CONFORMITY MANUFACTURER: Gage Bilt Inc. 44766 Centre Ct. Clinton Twp. Michigan (586-226-1500) WE DECLARE THAT THE EQUIPMENT SPECIFIED HEREIN CONFORMS TO THE FOLLOWING DIRECTIVES AND STANDARDS Machinery Directive 2006/42/EC EN12100-1 & EN12100-2 EN792-1:2000+A1 EU REPRESENTATIVE Edgar Hausmann GmbH Förster-Busch-Str. 10 D-34346 Hann. Münden Germany EQUIPMENT DESCRIPTION: GB731 FASTENER INSTALLATION TOOL This procuct specified above conforms to the above dIrectives and standards.

This manual is also suitable for:

1702

Table of Contents