Advertisement
Three-position Enabling Switches/Grip Style Three-position Enabling Switches
HE1G/HE1G-L Grip Style Enabling Switch
Wire Length inside the Grip Style Enabling Switch
Wire length L1, L2 (mm)
Wire stripping length L3 (mm)
L1
L3
L2
L3
• Applicable Wire Size
<Direct wiring>
0.14 to 1.5 mm
2
(one wire per terminal)
Note: When using stranded wire, make sure that adjoining
terminals are not short-circuited by frayed wires. Also, do
not solder the wires to avoid frayed wires.
<Ferrules>
Recommended ferrules (Phoenix Contact)
Part No.
Applicable Wire
AI 0,5-8 WH
0.34 to 0.5 mm
AI 0,75-8 GY
0.5 to 0.75 mm
AI 1,0-8 RD
0.75 to 1.0 mm
AI 1,5-8 BK
1.0 to 1.5 mm
Crimping tool: CRIMPFOX UD6
Recommended Tightening Torque
Parts for Tightening
Rubber boot and the base
A
(M4 screw × 3)
B
Connector and grip style enabling switch
C
Connector and connector
D
Terminal screw (M3 screw × 8)
E
Do not remove screws
The torque of screws B and C in the table above are values
when the recommended connector is used. When using another
connec tor, refer to the specifications of the connector used.
Rubber
Boot Kit
Base
Base
E
Rubber
Boot Kit
HE1G-L (Internal Connector)
Wire Length inside the Switch
Sheath Strip
Applicable Connector
20 ±2mm
on Cable Side
• Applicable Wire Size
• 0.05 to 0.86mm
(AWG18 to 30): Check the compliance with
2
receptacle and contact.
Tool: 1762846-1 (manual tool)
Observe the requirements of GS-ET-22: 2003, 4.2.6 for wiring.
Note: When using stranded sires, make sure that loose wires do
not cause short circuit. Also, do not solder the terminals
to prevent loose wires. Use copper wire of 60°C or 75°C
temperature rating in order to comply with UL508. Observe
the requirements of GS-ET-22: 2003, 4.2.6 for wiring.
28
Terminal No. 1–4
Terminal No. 5–8
L1 = 40 mm
L2 = 27 mm
L3 = 6 mm
Cable Gland
Base
Terminal No.
2
2
2
2
Torque
1.2 ± 0.1 N·m
4.0 ± 0.3 N·m
4.0 ± 0.3 N·m
0.5 to 0.6 N·m
—
B C
A (M4 Screw × 3)
E
D
Base
Recommended Tightening Torque
Parts for Tightening
A Base and rubber kit (M4 screw × 3)
B Cable gland and grip style enabling switch
C Cable gland
D Do not touch
Note: The recommended tightening torques of B and C are for
the supplied cable gland. When using another cable gland,
refer to the tightening torque of the cable gland used.
Rubber Boot Kit
Base
D
D
Base
Rubber Boot Kit
HE2G (Solder Terminal)
Wire Length inside the Switch
Grip Style Enabling Switch
NO1 C1 11 12 31 32 NO2 C2 C NO NC
Wire
stripping
40 45 50 60 50 60 85 80
length
L1 (mm)
Wire
stripping
length
L2 (mm)
L2
L1
<Example>
Pilot Light
Emergency
Stop Switch
Emergency
Stop Switch
Grip Style
Enabling Switch
• Applicable Wire Size in Solder Terminal
0.5mm
2
maximum (Observe the requirements of IEC 60204-1 for
wiring.)
Torque
1.1 to 1.3 N·m
3.7 to 4.3 N·m
3.7 to 4.3 N·m
—
Cable Gland
A (M4 screw × 3)
B
C
Base
Momentary
Emergency
Pushbutton/
Pilot
Stop
Key Selector
Light
Switch
Switch
1
2
+
120
110
115
L2=5mm
Sheath
Momentary Pushbutton/
Key Selector Switch
Grip Style
Enabling Switch
–
Advertisement
