Table of Contents
Advertisement
Specifications - JH 19T14 MMD-xxx-Axxx
PRODUCT SPECIFICATIONS - JH 19T14 MMD-xxx-Axxx
TFT Technology:
• High Quality SHARP TFT
• 19.0 inch viewable image size
• Active Matrix, Thin Film Transistor (TFT)
• MVA Premium™ Technology
TFT Characteristics:
• Pixel Number
: 1280 x 1024
• Pixel Pitch (RGB)
: 0.294 (H) x 0.294 (V) mm
• Response Time
: 12 ms (typical), "black" to "white"
• Contrast Ratio
: 900:1 (typical)
• Light Intensity
: 300 cd/m2 (typical)
• Viewable Angle
: +/- 85 deg. (typical) (Up/Down/Left/Right)
• Active Display Area
: 376.32 (H) x 301.056 (V) mm
• Max Colors
: 16.7 millions
Synchronisation:
Sync Signal:
• Digital separate synchronisation
• Composite synchronisation
• Synchronisation on green.
• Auto detects VGA -> WUXGA, interlaced and non interlaced
• Video Signal
: Analog RGB 0,7Vp-p
: Input Impedance 75 Ohm
Synchronisation Range:
• Horizontal
: 15,0 kHz to 91,1 kHz
• Vertical
: 60 Hz* to 85 Hz
* Recommended for optimum picture quality
Supported Signals:
Resolutions:
• VGA
: 640 x 480 (including 640 x 350)
• SVGA
: 800 x 600 (including 720 x 400)
• XGA
: 1024 x 768
• SXGA
: 1280 x 1024*
• UXGA
: 1600 x 1200
• WUXGA
: 1920 x 1200
* Recommended for optimum picture quality. (60 Hz only)
Video Signals (with HATTELAND® Multifunction Cable):
• Interlaced NTSC and PAL/SECAM video
• Composite video
Power Specifications:
Multi-power Supply:
• 115&230VAC - 50/60Hz + 24 VDC
Note: You may connect either AC power or DC power or both. In case both
sources are connected, power will be sourced from the AC input. If AC input
is lost, there will be a uninterrupted switch-over to DC input.
Power Consumption:
Operating
: 100 W (max)
Typical Type Numbers:
• JH 19T14 MMD-MA1-AAAA = Standard AC+DC, Keypad controls only
• JH 19T14 MMD-MA1-AAAC = Standard AC+DC, Capacitive Touch Screen
• JH 19T14 MMD-MA1-AOBA = Standard AC+DC, Bonded, Potmeter Controls, Buzzer
Buzzer-Potmeter-Keypad
MMD-xxx-xxBx
For a full overview, please review our typenumber sheet found on our website:
http://www.hatteland-display.com/pdflink/ind100780-1.php
T E S T I N G / A P P R O V A L S
IEC 60945 4th (EN 60945:2002)
ABS - American Bureau of Shipping
IND100129-100
- JH 19T14 MMD-Mxx-Axxx
Keypad
MMD-xxx-xxAx
This product have been tested / type approved by the following classification societies:
ClassNK - Nippon Kaiji Kyokai
BV - Bureau Veritas
Note: All specifications are subject to change without prior notice!
Physical Considerations:
• 483 (W) x 444 (H) x 82 (D) mm / 19.02" (W) x 17.48" (H) x 3.23" (D)
• Weight: 11.50 kg (approx)
Signal Terminals:
• DVI-I Signal IN
• RGB Signal IN
• RGB Signal OUT
• Multifunction
• USB I/O
• AC Power IN
• AC Power OUT
• DC Power IN
**Tested at recommended resolutions. The RGB output signal is at same resolution and sync as the
RGB input. The output is working even if the display unit is turned off, but power cable/supply must
be connected/provided.
HATTELAND® Multifunction Cable:
The factory standard cable is delivered with the following connectors.
Standard cable length is 30cm. Art: #1=VSD100692-4 / #2=VSD100692-3
• COM1
#1
• Composite Video IN
• COM1
#2
• Composite Video IN
• COM Touch
Customized cables are possible to support more built-in signals, like: RS-232, RS-485, RS-422/RS-485,
Buzzer, ON/OFF, Touch (RS-232 or PS/2), 1 x S-Video IN, 3 x Composite Video IN, Remote External
User Controls, Alternative Keypad interface (i2c) and reserved for other signals. Custom cable lengths
can be manufactured.
User Controls:
On front bezel - Keypad control (IP66) xxx-xxAx models:
• Power On/Off and On Screen Display Menu (push button)
• Brightness Control (up/down - push buttons)
• Hotkeys (left/right - push buttons)
• Mode Status Red/Green Illuminated LED-Ring Indicator
On front bezel - Potmeter control (IP66) xxx-xxBx models:
• Power On/Off and On Screen Display Menu (push button)
• Brightness Control (rotary control)
• Hotkeys (left/right - push buttons)
• Mode Status Red/Green Illuminated LED-Ring Indicator
• Speaker / Buzzer
Environmental Considerations:
• Operating
: Temperature -15 deg. C to +55 deg. C
- Humidity up to 95%
• Storage
: Temperature -20 deg. C to +60 deg. C
- Humidity up to 95%
• IP Rating
: Protection (EN60529): IP66 front - IP20 rear
• Compass Safe Dist. : JH19T14MMD-xxx-xxxx - Std: 1.60m Steering: 1.05m
Safety Considerations:
Even although the test conditions for bridge units provide for a maximum
operating temperature of 55°C, continuous operation of all electronic
components should, if possible, take place at ambient temperatures of only
25°C. This is a necessary prerequisite for long life and low service costs.
Available Accessories:
• Cables
= VSD100692-3, VSD100692-4 or customized cables.
• JH MMDBR STD-A1 = Bracket
• JH 19BRD STD-A1 = Mounting Bracket EN60945 Tested
• JH MMDRO STD-A1 = Rotary Bracket
• JH 19TSV STD-A1 = Sun Visor
• JH 19VED STD-A1 = Vesa Bracket
• JH 19TAP STD-A1 = 21" CRT Adapter frame
• JH 19TAP STD-B1 = 21" CRT Custom Adapter frame
• JH 19TWC STD-B1 = Water Cover
*Please see user manual for drawings/measurements.
Factory Options:
• Resistive* or Capacitive Touch Screen / Optical Bonding Technology*
• Color Calibrated models (ECDIS)
*Note that all 19 inch with resistive touch screens can not be combined with bonding.
& C E R T I F I C A T E S
GL - Germanischer Lloyd
CCS - China Classification Society LRS - Lloyd's Register of Shipping
50
INB100036-1 (Rev 21)
: 1 x 29p DVI Female (or as RGB IN with adapter)
: 1 x 15p HD D-SUB (female)
: 1 x 15p HD D-SUB (female) - Clone of RGB IN**
: 1 x 160p D-SUB (female) - Also see table below
: 1 x TYPE B Conn. (female) Reserved for future use
: 1 x Std IEC Inlet
: 1 x Std IEC Outlet (5A Max)
: 1 x 2p D-SUB Connector (male) - Amphenol FCC17
: 1 x 9p D-SUB (female) - RS232
: 3 x BNC (female)
: 1 x 9p D-SUB (female) - RS232
: 3 x BNC (female)
: 1 x 9p D-SUB (female) - For touch screen
DNV - Det Norske Veritas
2/2
Advertisement
Table of Contents
