Table of Contents
Advertisement
Pin Assignments - Common Connectors
Note: Not all connectors may be available on your specific product. This depends on the amount of additional hardware installed from factory,
or customized solutions. These pin assignments are for the common connectors used.
Pin 01
T.M.D.S. Data2 - (Digital - RED link 1)
Pin 02
T.M.D.S. Data2 + (Digital + RED link 1)
Pin 03
T.M.D.S. Data2/4 Shield
Pin 04
T.M.D.S. Data4 - (Digital - GREEN link 2)
Pin 05
T.M.D.S. Data4 + (Digital + GREEN link 2)
Pin 06
DDC Clock
Pin 07
DDC Data
Pin 08
Analog Vertical Sync (DVI-I only)
Pin 09
T.M.D.S. Data1 - (Digital - GREEN link 1)
Pin 10
T.M.D.S. Data1 + (Digital + GREEN link 1)
Pin 11
T.M.D.S. Data1/3 Shield
Pin 12
T.M.D.S. Data3 - (Digital - BLUE link 2)
Pin 13
T.M.D.S. Data3 + (Digital + BLUE link 2)
Pin 14
+5V Power (for standby mode)
Pin 15
Ground (for +5V and analog sync)
Pin 16
Hot Plug Detect
Pin 17
T.M.D.S. Data0 - (Digital - BLUE link 1) and digital sync.
Pin 18
T.M.D.S. Data0 + (Digital + BLUE link 1) and digital sync.
Pin 19
T.M.D.S. Data0/5 Shield
Pin 20
T.M.D.S. Data5 - (Digital - RED link 2)
Pin 21
T.M.D.S. Data5 + (Digital - RED link 2)
Pin 22
T.M.D.S. Clock Shield
Pin 23
T.M.D.S. Clock + (Digital clock + (Links 1 and 2)
Pin 24
T.M.D.S. Clock - (Digital clock - (Links 1 and 2)
Pin C1
Analog RED
Pin C2
Analog GREEN
Pin C3
Analog BLUE
Pin C4
Analog Horizontal Sync.
Pin C5
Analog Ground (return for RGB signals)
DDC = Display Data Channel /// T.M.D.S = Transition Minimized Differential Signal /// PIN C1,C2,C3,C4 = Only present on DVI-I connectors.
NOTE: Connector shows a DUAL LINK design, but some units may not support it. Only products with 1920x1200 or more in resolution
require / support DUAL LINK.
Pin Assignments - 15P HD RGB VGA
5
4 3 2 1
10 9 8 7 6
15 14 13 12 11
Pin 01
Red, analog
Pin 02
Green, analog
Pin 03
Blue, analog
Pin 04
Reserved for monitor ID bit 2 (grounded)
Pin 05
Digital ground
Pin 06
Analog ground red
Pin 07
Analog ground green
Pin 08
Analog ground blue
Pin 09
+5V power supply for DDC (optional)
Pin 10
Digital ground
Pin 11
Reserved for monitor ID bit 0 (grounded)
Pin 12
DDC serial data
Pin 13
Horizontal sync or composite sync, input
Pin 14
Vertical sync, input
Pin 15
DDC serial clock
Appendix
IND100241-9
Pin Assignments - 24P DVI-I
1 2 3 4 5 6 7 8
C1 C2
9 10 11 12 13 14 15 16
C5
17 18 19 20 21 22 23 24 C3 C4
Pin 2: Negative Data
Pin 3: Positive Data
106
Connectors are seen from users Point Of View (POV).
Pin Assignments - USB TYPE B
Pin 1: VCC +5V
Pin 4: Ground
INB100036-1 (Rev 21)
Advertisement
Table of Contents
