1. Manuals
  2. Brands
  3. Jeep Manuals
  4. Automobile
  5. Gladiator 2024
  6. Owner's manual

Jeep Gladiator 2024 Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
2024 GLA D IATOR
OW N E R ' S M A N UA L

Advertisement

Table of Contents
loading

Related Manuals for Jeep Gladiator 2024

Summary of Contents for Jeep Gladiator 2024

  • Page 1 2024 GLA D IATOR OW N E R ’ S M A N UA L...
  • Page 2 ROADSIDE ASSISTANCE This Owner’s Manual illustrates and describes the operation of features and equipment that are either standard or optional on this vehicle. This manual may also include a description of features and equipment that are no longer available or were not ordered on this vehicle.

  • Page 3: Table Of Contents

    TABLE OF CONTENTS INTRODUCTION................7 GETTING TO KNOW YOUR VEHICLE.
  • Page 4 UNIVERSAL GARAGE DOOR OPENER INTRODUCTION Automatic Door Locks — If Equipped ..24 (HOMELINK®) — IF EQUIPPED ... . . 45 Child-Protection Door Lock System — SYMBOLS KEY .
  • Page 5 Cybersecurity ....114 Jeep® Wireless Speaker — If Equipped ..61 BED RAIL TIE DOWN SYSTEM — IF EQUIPPED ..94...
  • Page 6 AUTOMATIC TRANSMISSION — IF EQUIPPED ..121 To Manually Turn On The Stop/Start System . 135 Recreational Towing — Four-Wheel Drive Ignition Park Interlock ....122 System Malfunction .
  • Page 7 IF YOUR ENGINE OVERHEATS ... . 242 Forward Collision Warning (FCW) With Manual Transmission — If Equipped ..261 MANUAL PARK RELEASE — IF EQUIPPED ..242 Mitigation —...
  • Page 8 WHEEL AND TIRE TORQUE SPECIFICATIONS . . . 293 MOPAR® PARTS ....300 Torque Specifications ....293 REPORTING SAFETY DEFECTS .

  • Page 9: Introduction

    FCA US LLC aims at a constant improvement of the vehicles produced. For this reason, it reserves the right to make changes to the model described for technical and/or commercial reasons. For further information, contact an authorized dealer. When it comes to service, remember that authorized dealers know your Jeep® best, have factory-trained technicians and genuine Mopar® parts, and care about your satisfaction.

  • Page 10: Symbols Key

    INTRODUCTION SYMBOLS KEY ROLLOVER WARNING Utility vehicles have a significantly higher rollover rate than other types of vehicles. This vehicle has a higher ground clearance and a higher center of gravity than many pas- WARNING! These statements apply to operating pro- senger vehicles.

  • Page 11: Campers

    INTRODUCTION CAMPERS Red Warning Lights This vehicle is NOT recommended for slide-in camper applications. Battery Charge Warning Light page 106 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Door Open Warning Light page 106 Any modifications or alterations to this vehicle could seriously affect its roadworthi- ness and safety and may lead to a collision resulting in serious injury or death.
  • Page 12 INTRODUCTION Red Warning Lights Yellow Warning Lights Oil Pressure Warning Light Anti-Lock Brake System (ABS) Warning Light page 107 page 108 Electronic Stability Control (ESC) Active Warning Light Oil Temperature Warning Light page 107 page 108 Seat Belt Reminder Warning Light Electronic Stability Control (ESC) OFF Warning Light page 107 page 108...
  • Page 13 INTRODUCTION Yellow Warning Lights Yellow Warning Lights Low Washer Fluid Warning Light Cruise Control Fault Warning Light page 109 page 110 Engine Check/Malfunction Indicator Warning Light (MIL) Sway Bar Fault Warning Light page 109 page 110 Service 4WD Warning Light Tire Pressure Monitoring System (TPMS) Warning Light page 109 page 110...
  • Page 14 INTRODUCTION Yellow Indicator Lights Yellow Indicator Lights Axle Locker Fault Indicator Light Off Road+ Indicator Light page 111 page 111 Rear Axle Lock Indicator Light Cargo Light On Indicator Light page 111 page 111 Front And Rear Axle Lock Indicator Light Sway Bar Indicator Light page 111 page 111...
  • Page 15 INTRODUCTION Green Indicator Lights White Indicator Lights Cruise Control SET Indicator Light Adaptive Cruise Control (ACC) Ready Indicator Light page 112 page 112 Front Fog Indicator Light Adaptive Cruise Control (ACC) Ready Indicator Light page 112 page 112 Parking/Headlights On Indicator Light Adaptive Cruise Control (ACC) Set Indicator Light page 112 page 112...
  • Page 16 INTRODUCTION White Indicator Lights Rear Seat Unoccupied Indicator Light page 113 Cruise Control Ready Indicator Light page 113 Cruise Control SET Indicator Light page 113 Cruise Control Ready Indicator Light page 113 Selec-Speed Control (SSC) Indicator Light page 113 Blue Indicator Lights High Beam Indicator Light page 113...

  • Page 17: Getting To Know Your Vehicle

    GETTING TO KNOW YOUR VEHICLE NOTE: KEYS CAUTION! • In case the ignition switch does not change with the The electrical components inside of the key fob may push of a button, the key fob may have a low or fully KEY FOB be damaged if the key fob is subjected to strong elec- depleted battery.
  • Page 18 GETTING TO KNOW YOUR VEHICLE Key Left Vehicle Feature • When a key fob battery is low, a warning will be indi- cated on the vehicle’s instrument cluster, and the If a valid key fob is no longer detected inside the vehicle fob LED will no longer illuminate with a button push.

  • Page 19: Sentry Key

    GETTING TO KNOW YOUR VEHICLE Programming And Requesting SENTRY KEY All of the key fobs provided with your new vehicle have Additional Key Fobs been programmed to the vehicle electronics page 302. The Sentry Key Immobilizer system prevents unauthor- Programming the key fob may be performed by an ized vehicle operation by disabling the engine.
  • Page 20 GETTING TO KNOW YOUR VEHICLE The push button ignition can be placed in the following WARNING! modes: • When exiting the vehicle, always remove the key • fob from the vehicle and lock your vehicle. The engine is stopped. • •...

  • Page 21: Remote Start - If Equipped

    GETTING TO KNOW YOUR VEHICLE NOTE: REMOTE START — IF EQUIPPED TO EXIT REMOTE START MODE • With Remote Start, the engine will only run for To drive the vehicle after starting the Remote Start sys- This system uses the key fob to start the 15 minutes.

  • Page 22: Remote Start Front Defrost Activation - If Equipped

    GETTING TO KNOW YOUR VEHICLE Manual Temperature Control (MTC) — If Equipped REMOTE START FRONT DEFROST REMOTE START CANCEL MESSAGE • In ambient temperatures of 40°F (4.5°C) or below, ACTIVATION — IF EQUIPPED One of the following messages will display in the instru- the climate settings will default to maximum heat, ment cluster if the vehicle fails to remote start or exits When Remote Start is active, and the outside ambient...

  • Page 23: To Arm The System

    GETTING TO KNOW YOUR VEHICLE TO ARM THE SYSTEM The Vehicle Security system is designed to protect your MANUAL DOOR LOCKS vehicle. However, you can create conditions where the Follow these steps to arm the Vehicle Security system: All doors are equipped with an interior rocker-type door system will give you a false alarm.

  • Page 24: Power Door Locks - If Equipped

    GETTING TO KNOW YOUR VEHICLE NOTE: WARNING! WARNING! • Passive Entry may be programmed on/off through • Never leave children alone in a vehicle, or with • For personal security reasons and safety in a colli- Uconnect Settings page 166. access to an unlocked vehicle.
  • Page 25 GETTING TO KNOW YOUR VEHICLE To Lock The Vehicle’s Doors FOBIK-Safe only executes in vehicles with Passive Entry. There are three situations that trigger a FOBIK-Safe With one of the vehicle’s Passive Entry key fobs within search in any Passive Entry vehicle: 5 ft (1.5 m) of the driver or passenger front door •...

  • Page 26: Automatic Door Locks - If Equipped

    GETTING TO KNOW YOUR VEHICLE NOTE: WARNING! • After pushing the door handle button, the driver Avoid trapping anyone in a vehicle in a collision. must wait three seconds before locking or unlocking Remember that the rear doors can only be opened the doors, using any Passive Entry door handle.
  • Page 27 GETTING TO KNOW YOUR VEHICLE Outside rearview mirrors are mounted on the doors. If you choose to remove the doors, see an authorized dealer for a replacement cowl-mounted outside mirror. Federal law requires outside mirrors on vehicles for on-road use. NOTE: When front doors are removed, the message “Blind Spot Alert Temporarily Unavailable”...
  • Page 28 GETTING TO KNOW YOUR VEHICLE 5. Push and hold down the black security tab under the wiring harness, and lift the harness lever into the open position. Door Check Arm Hinge Pin Locations 8. With the door open, lift the door with the help of 2.
  • Page 29 GETTING TO KNOW YOUR VEHICLE 4. Using your fingers, turn the screw clockwise at least 1. With light finger pressure, seat the wiring connector straight into the wiring harness until the wiring har- two full turns. Gently pull on the screw to ensure it is secure.

  • Page 30: Rear Door Removal

    GETTING TO KNOW YOUR VEHICLE NOTE: WARNING! When reinstalling the door check arm attachment screw, screw torque should be between 11.76 ft·lb / • All occupants must wear seat belts during off-road 16 N·m and 27.9 ft·lb / 38 N·m. operation with doors removed.

  • Page 31: Door Off Mirror Kit - If Equipped

    GETTING TO KNOW YOUR VEHICLE NOTE: CAUTION! Squeeze the tab on the base of the wiring harness. • This will unlock the connector tab, allowing the wir- Do not overtighten Torx fasteners. Damage to the ing connector to be unplugged. Unhook the wire vehicle’s parts will occur.
  • Page 32 GETTING TO KNOW YOUR VEHICLE To install the Door Off Mirrors, proceed as follows: 5. Insert the hinge shoulder bolt through the bottom of the upper door hinge up into the mirror bracket, 1. Remove both front doors page 24. then rotate the bracket knob toward the rear of the 2.

  • Page 33: Half-Doors - If Equipped

    GETTING TO KNOW YOUR VEHICLE Half-Door Installation NOTE: If this kit is being installed with the optional lamp To install the front or rear half-doors, proceed as bracket, the bracket bushing from step 4 is not needed. follows: Use the spacer from the lamp bracket. 1.
  • Page 34 GETTING TO KNOW YOUR VEHICLE NOTE: CAUTION! For front doors, make sure the wiring harness is closed completely. • Do not close the door before reattaching the door check to the body. Damage may occur to the door check. • Do not overtighten Torx fasteners, damage to the vehicle’s parts will occur.
  • Page 35 GETTING TO KNOW YOUR VEHICLE NOTE: Lower Door Adjustment Only adjust the door to fit correctly against the striker. DO NOT adjust the striker, as this could affect the posi- CAUTION! tioning of the full door. Upon first installation of the half-doors, slowly close If the door does not center align between the latch and each door to check for body contact.
  • Page 36 GETTING TO KNOW YOUR VEHICLE 2. With the bolts loose, the door can be moved forward by pushing the door handle toward the front of the vehicle, and/or upward by grabbing the door handle and lifting towards the roof. 3. Once the gaps between the door and vehicle body are uniform around the entire door, tighten the door hinge bolts to 20.3 ft·...
  • Page 37 GETTING TO KNOW YOUR VEHICLE Half-Door Mirror Installation 4. Tighten the nut inside the bottom of the post using c. Slide the shim onto a pencil or similar tool. the wrench and make sure the screw head is flush d. Remove the paper backing from the adhesive To install the front door exterior mirrors on the half- to the post.

  • Page 38: Steering Wheel

    GETTING TO KNOW YOUR VEHICLE 3. Place the base of the exterior mirror into the hole on To unlock the steering column, push the control down- the door, and support it while attaching the three ward (toward the floor). To tilt the steering column, mirror bolts through the inside of the door using a move the steering wheel upward or downward as #T40 Torx head driver.

  • Page 39: Seats

    GETTING TO KNOW YOUR VEHICLE NOTE: WARNING! The engine must be running for the heated steering • wheel to operate. Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat For information on use with the Remote Start system, belts.

  • Page 40: Manual Adjustment Front Seats - If Equipped

    GETTING TO KNOW YOUR VEHICLE Reclining The Seatback Forward Or MANUAL ADJUSTMENT FRONT WARNING! Rearward SEATS — IF EQUIPPED • Adjusting a seat while driving may be dangerous. The seatback can be reclined both forward and rear- Manual Front Seat Forward/Rearward Moving a seat while driving could result in loss of ward.

  • Page 41: 60/40 Split Folding Rear Seat

    GETTING TO KNOW YOUR VEHICLE Manual Front Seatback Recline • The center head restraints must be in the lowest Adjustment position to avoid contact with the center console when folding the seat. To recline the seat, pull on the recline strap and lean forward or rearward, depending on the direction you WARNING! would like the seatback to move.

  • Page 42: Rear Seat Stadium Position

    GETTING TO KNOW YOUR VEHICLE To raise the seatback to the proper position, manually WARNING! lift the seatback until it locks into place. To return the head restraint to the proper position, manually lift up Be certain that the seatback is securely locked into until it locks into place.

  • Page 43: Heated Seats - If Equipped

    GETTING TO KNOW YOUR VEHICLE NOTE: 2. Raise the seat bottom upward into the Stadium REAR SEAT ARMREST — Position. IF EQUIPPED • The engine must be running for the heated seats to operate. The center part of the rear seat can also be used as a •...

  • Page 44: Head Restraints

    GETTING TO KNOW YOUR VEHICLE Rear Head Restraints HEAD RESTRAINTS The rear seat is equipped with nonadjustable, but fold- Head restraints are designed to reduce the risk of injury able, outboard head restraints, as well as an adjust- by restricting head movement in the event of a rear able, removable center head restraint.

  • Page 45: Uconnect Voice Recognition

    GETTING TO KNOW YOUR VEHICLE • UCONNECT VOICE RECOGNITION To reinstall the head restraint, put the head restraint You can interrupt the help message or system posts into the holes and push downward. Then, adjust it prompts by pushing the VR button and saying a to the appropriate height using the adjustment button.

  • Page 46: Mirrors

    GETTING TO KNOW YOUR VEHICLE NOTE: MIRRORS The Automatic Dimming Mirror feature is disabled when the vehicle is in REVERSE to improve the driver’s rear INSIDE REARVIEW MIRROR view. Manual Mirror — If Equipped The rearview mirror can be adjusted up, down, left, and right.

  • Page 47: Power Mirrors - If Equipped

    GETTING TO KNOW YOUR VEHICLE UNIVERSAL GARAGE DOOR OPENER For information on the Door Off Mirror Kit (if equipped) The power mirror controls consist of mirror select but- when the front doors are removed, see page 29. tons and a four-way mirror control switch. To adjust a mirror, push either the L (left) or R (right) button to (HOMELINK®) —...

  • Page 48: Before You Begin Programming Homelink

    GETTING TO KNOW YOUR VEHICLE NOTE: • To operate HomeLink®, push and release any of the PROGRAMMING HOMELINK® TO A programmed HomeLink® buttons. These buttons Erasing all channels should only be performed when GARAGE DOOR OPENER will activate the devices they are programmed to programming HomeLink®...

  • Page 49: Programming Homelink® To A Miscellaneous Device

    GETTING TO KNOW YOUR VEHICLE 1. At the garage door opener motor (in the garage), PROGRAMMING HOMELINK® TO A CANADIAN/GATE OPERATOR locate the “LEARN” or “TRAIN” button. This can usu- MISCELLANEOUS DEVICE PROGRAMMING ally be found where the hanging antenna wire is attached to the garage door opener motor.

  • Page 50: Security

    GETTING TO KNOW YOUR VEHICLE 4. Watch for the HomeLink® indicator to change flash The HomeLink® universal transmitter is disabled when EXTERIOR LIGHTS rates. When it changes, it is programmed. It may the Vehicle Security system is active. take up to 30 seconds or longer in rare cases. The TROUBLESHOOTING TIPS HEADLIGHT SWITCH garage door may open and close while you are...

  • Page 51: Daytime Running Lights (Drls) - If Equipped

    GETTING TO KNOW YOUR VEHICLE NOTE: With the headlight switch activated, push the multifunc- tion lever toward the instrument panel to switch the For vehicles sold in Canada, rotate the headlight switch headlights to high beams. The lever will return to the clockwise from the parking lights and instrument panel centered position.

  • Page 52: Flash-To-Pass

    GETTING TO KNOW YOUR VEHICLE • Broken, muddy, or obstructed headlights and tail- LIGHTS-ON REMINDER lights of vehicles in the field of view will cause head- If the headlights or parking lights are left on after the lights to remain on longer (closer to the vehicle). ignition is placed in the OFF position, the vehicle will Also, dirt, film, and other obstructions on the wind- chime when the driver’s door is opened.

  • Page 53: Bed Lights - If Equipped

    GETTING TO KNOW YOUR VEHICLE BED LIGHTS — IF EQUIPPED The bed lights will turn on for approximately 60 seconds DIMMER CONTROL when a key fob unlock button is pushed, as part of the The bed lights will illuminate the bed and cargo area. The dimmer control is part of the headlight switch and Illuminated Entry feature.

  • Page 54: Windshield Wipers And Washers

    GETTING TO KNOW YOUR VEHICLE With the parking lights or headlights on, rotating the Rotate the end of the lever upward to the first detent If the lever is pulled while in the off position, the wipers dimmer control upward will increase the brightness of past the intermittent settings for low-speed wiper will operate for two or three wipe cycles.

  • Page 55: Climate Controls

    GETTING TO KNOW YOUR VEHICLE NOTE: CLIMATE CONTROLS (button on the touchscreen grayed out) if conditions exist that could create fogging on the inside of the wind- The MAX A/C button is only available on the shield. The A/C can be deselected manually without touchscreen.
  • Page 56 GETTING TO KNOW YOUR VEHICLE Rear Defrost Button Mode Control Push the blue button on the faceplate or touchscreen or press and slide the tempera- Press and release the Rear Defrost Control Turn the mode control knob or press one of ture bar towards the blue arrow button on button on the touchscreen, or push and the Mode buttons on the touchscreen to...

  • Page 57: Manual Climate Control Descriptions And Functions

    GETTING TO KNOW YOUR VEHICLE Mix Mode Front Defrost • If fog or mist appears on the windshield or side glass, select Defrost mode, and increase blower Air is directed through the floor, defrost, and Turn the Mode control knob to Front Defrost speed if needed.

  • Page 58: Automatic Temperature Control (Atc) - If Equipped

    GETTING TO KNOW YOUR VEHICLE Temperature Control Panel Mode Climate Control OFF Button Temperature Control regulates the temperature of the Air comes from the outlets in the instrument Press and release this button to turn the air forced through the climate system. panel.

  • Page 59: Climate Voice Commands

    GETTING TO KNOW YOUR VEHICLE Winter Operation Stop/Start System — If Equipped To provide you with maximum comfort in the Automatic mode during cold start-ups, the blower fan will remain To ensure the best possible heater and defroster perfor- While in an Autostop, the Climate Control system may on low until the engine warms up.

  • Page 60: Interior Storage And Equipment

    GETTING TO KNOW YOUR VEHICLE Console Storage Compartment Non-Locking Storage Wall INTERIOR STORAGE AND EQUIPMENT The center console has both an upper and lower stor- age compartment. To open the upper storage compart- STORAGE ment, lift the top latch. To access the lower storage compartment, lift the bottom latch.
  • Page 61 GETTING TO KNOW YOUR VEHICLE Rear Wall Netting If equipped, the Locking Storage Bin is located below Your Locking Storage Bin also has a front handle that the rear seats. It can be accessed by folding the rear makes it easier to carry and pull out from the floor of The rear wall netting can be accessed the same way as seat bottom upward into the Stadium Position.

  • Page 62: Lighted Cupholders - If Equipped

    GETTING TO KNOW YOUR VEHICLE AUX/USB CONTROL The Media Hub is located on the instrument panel, below the climate controls. Behind the media hub access door, the Media Hub contains one AUX port, a Type C USB port and one standard USB port. Both USB ports allow you to play music from smartphones or USB devices through the vehicle’s sound system.

  • Page 63: Jeep® Wireless Speaker - If Equipped

    A third and fourth USB port are located behind the cen- collision. ter console, above the power inverter. Both ports are charge only. JEEP® WIRELESS SPEAKER — IF EQUIPPED Your vehicle may be equipped with a wireless Bluetooth® speaker. Rear Speaker Outlets Getting To Know Your Speaker 1 —...
  • Page 64 The Jeep® wireless speaker is located behind the right NOTE: rear passenger seat. In order to access the Jeep® wire- less speaker, the seat will need to be folded down or Jeep® wireless speaker will not charge within vehicle tilted forward.
  • Page 65 The Jeep® wireless speaker contains a lithium-ion rechargeable battery. Typical charging temperatures for these types of batteries are from 0 to 45°C (32 to 113°F). NOTE: The functions described are for when the Jeep® wireless speaker is undocked from the vehicle. When plugged into the docking station, the Jeep® wireless speaker functions as part of the vehicle’s sound system.
  • Page 66 To reduce the risk of fire or electric shock, do not device, or expose them to a strong shock. Do not 1. Push and hold the power button on both Jeep® expose the Jeep® wireless speaker to rain or moisture pierce, crush, dent, or deform the batteries or power wireless speakers until both speakers turn on.

  • Page 67: Power Outlets

    Please refer to the information on the bottom of the To avoid serious injury or death: • Jeep® wireless speaker for electrical and safety infor- Do not insert any objects into the receptacles. mation before installing or operating the Jeep® wire- •...

  • Page 68: Power Inverters - If Equipped

    GETTING TO KNOW YOUR VEHICLE POWER INVERTERS — IF EQUIPPED CAUTION! There is a 115 V (400 W) maximum inverter outlet • Do not exceed the maximum power of 160 W located on the back of the center console to convert (13 A) at 12 Volts.

  • Page 69: Auxiliary Switches - If Equipped

    GETTING TO KNOW YOUR VEHICLE The power inverter is designed with built-in overload protection. If the power rating of 400 W is exceeded, the power inverter automatically shuts down. Once the electrical device has been removed from the outlet, the inverter should automatically reset.

  • Page 70: Power Windows - If Equipped

    GETTING TO KNOW YOUR VEHICLE Wire Color Chart Circuit Function Fuse Wire Color Locations Aux Switch 1 F93 – 40 Amp Beige/Pink Interior (passenger side under instrument panel) & Underhood (right side near battery) Aux Switch 2 F92 – 40 Amp Green/Pink Interior (passenger side under instrument panel) &...

  • Page 71: Manual Sliding Rear Window - If Equipped

    GETTING TO KNOW YOUR VEHICLE MANUAL SLIDING REAR WINDOW — The window lockout switch allows you to disable the window controls on the rear passenger doors. To dis- IF EQUIPPED able the window controls, rotate the switch downward. To enable the window controls, rotate the switch To open the rear sliding window, push the release but- upward.

  • Page 72: Lowering The Soft Top

    GETTING TO KNOW YOUR VEHICLE LOWERING THE SOFT TOP If the temperature is below 72°F (24°C) and/or the top CAUTION! has been folded down for a period of time, the top will Use this QR code to access your digital appear to have shrunk when you raise it, making it diffi- •...
  • Page 73 GETTING TO KNOW YOUR VEHICLE Side View Top And Components 1 — #1 Bow 6 — Quarter Panel Upper Hook And Loop 2 — #2 Bow 7 — Quarter Panel Vertical Retainer 3 — #3 Bow 8 — Rear Window Vertical Retainer 4 —...
  • Page 74 GETTING TO KNOW YOUR VEHICLE Rear Window View And Components 1 — Top Retainer 4 — Pull Tabs 2 — Left Vertical Retainer 5 — Lower Center Retainer 3 — Lower Retainers 6 — Right Vertical Retainer...
  • Page 75 GETTING TO KNOW YOUR VEHICLE Lowering The Soft Top Into The Sunrider® Position: Use this QR code to access your digital experience. 1. Fold both sun visors forward against the windshield. Scan me 2. Release the header latches from the crossbar by pulling the handle down- ward.
  • Page 76 GETTING TO KNOW YOUR VEHICLE Removing The Rear Window And 3. After removing the rear window, remove the quarter Quarter Panel Cover Assemblies panel cover assemblies starting with either side. Disengage the quarter panel cover assembly from the bottom by pulling the fabric at the bottom NOTE: upward.
  • Page 77 GETTING TO KNOW YOUR VEHICLE NOTE: The quarter panel cover assemblies are marked “1” and “2” on the inside of the panel assembly. Step Five Step One 6. Repeat this procedure for the other quarter panel 2. Fold the divider upward, covering the rear window. cover assembly.

  • Page 78: Raising The Soft Top

    GETTING TO KNOW YOUR VEHICLE RAISING THE SOFT TOP 2. Using the side link, lift and push the soft top toward 3. From inside the vehicle, pull the handle on the the front of the vehicle, manually guiding the top header latch downward to engage the hook into its Use this QR code to access your digital into the closed position.
  • Page 79 GETTING TO KNOW YOUR VEHICLE Installing The Rear Window And Quarter Panel Cover Assemblies NOTE: Both quarter panel cover assemblies and the rear win- dow must ALL be removed together, or installed together. If the rear window and quarter panel cover assemblies were previously removed, proceed as follows to install: 1.

  • Page 80: Removing The Soft Top

    GETTING TO KNOW YOUR VEHICLE REMOVING THE SOFT TOP 3. Utilizing two people, lift the soft top up and away from the vehicle, careful to avoid the vehicle’s sport Use this QR code to access your digital bar and trim. Store the soft top in a safe, clean, and experience.

  • Page 81: Installing The Soft Top

    GETTING TO KNOW YOUR VEHICLE INSTALLING THE SOFT TOP NOTE: If installing the soft top immediately after removing the hard top, ensure the wire harness is stored properly, and not tucked under the belt rail page 83. 1. Install the belt rail on the rear of the vehicle. Secure the belt rail using the six fasteners with the provided #T50 Torx head driver and ratchet.

  • Page 82: Hard Top Front Panel(S) Removal

    GETTING TO KNOW YOUR VEHICLE Torque Specifi- CAUTION! cation For Torx Maximum Minimum Failure to follow these cautions may cause interior Fasteners water damage, stains or mildew: 119.5 in-lb 150.5 in-lb 106.2 in-lb • It is recommended that the top be free of water (13.5 N·m) (17.0 N·m) (12.0 N·m)
  • Page 83 GETTING TO KNOW YOUR VEHICLE Hard Top Components 1 — Right Side Panel 2 — Left Side Panel 3 — Hard Top NOTE: The left side panel must be removed before removing the right side panel.
  • Page 84 GETTING TO KNOW YOUR VEHICLE NOTE: 1. Fold down the sun visor against the windshield. 2. Turn the three L-shaped locks on the left side panel • Ensure the front panel latch is closed prior to insert- (one at the front, the rear, and outside), unlocking ing the panel into the panels bag.

  • Page 85: Hard Top Front Panel(S) Installation

    GETTING TO KNOW YOUR VEHICLE HARD TOP FRONT PANEL(S) 4. Remove the Torx head fasteners that secure the hard top to the vehicle: two along the interior body INSTALLATION side, rearward of the back doors, followed by the four fasteners along the back of the vehicle cab 1.
  • Page 86 GETTING TO KNOW YOUR VEHICLE 7. Remove the hard top from the vehicle. Install the provided edge protectors along the bottom edges of the hard top, and place the hard top on a soft sur- face to prevent damage. CAUTION! The removal of the Hard Top requires four adults located on each corner.

  • Page 87: Installing The Hard Top

    GETTING TO KNOW YOUR VEHICLE INSTALLING THE HARD TOP SUNRIDER® FOR HARD TOP — IF EQUIPPED If the door frames are installed from soft top usage, they must be removed prior to installation of the hard page 87. WARNING! To install the hard top, place the hard top on the vehicle while making sure that the top is sitting flush with the Do not open or close the Sunrider®...
  • Page 88 GETTING TO KNOW YOUR VEHICLE 8. From inside the vehicle, pull the handle on the header latch downward to engage the hook into its receiver. Pull the handle back upward while squeez- ing the hook, locking the latch into place. Repeat on the other side.

  • Page 89: Door Frame - If Equipped With A Soft Top

    GETTING TO KNOW YOUR VEHICLE CAUTION! • Careless handling and storage of the removable door frame(s) may damage the seals, causing water to leak into the vehicle's interior. • The door frame(s) must be positioned properly to ensure sealing. Improper installation can cause water to leak into the vehicle's interior.

  • Page 90: Door Frame Installation

    GETTING TO KNOW YOUR VEHICLE WARNING! Target Torque Specification Do not drive your vehicle on public roads with the Maximum Minimum For Torx door and/or door frame(s) removed as you will lose Fasteners the protection that they can provide. This procedure is furnished for use during off-road operation only.

  • Page 91: Folding Windshield

    GETTING TO KNOW YOUR VEHICLE speed of the vehicle be limited to 10 mph (16 km/h), LOWERING THE WINDSHIELD with low range operation preferred if you are driving off-road with the windshield folded down. 1. Before completing the following steps: ○...
  • Page 92 GETTING TO KNOW YOUR VEHICLE Adaptive Cruise Control (ACC)/Forward 3. Using the provided 15 mm socket, remove the two hex bolts and remove the wiper arms. Collision Warning (FCW) Sensor Protective Cover — If Equipped 4. Move to the inside of the vehicle and lower both sun visors.

  • Page 93: Raising The Windshield

    GETTING TO KNOW YOUR VEHICLE Cleaning Instructions HOOD 4. Reinstall the windshield wiper arms using the pro- vided 15 mm socket. First, align the tips of the During windshield down applications, dust/dirt can blade to the “T” mark in the glass. Then, while hold- accumulate in the cover and block the camera lens.

  • Page 94: Closing The Hood

    GETTING TO KNOW YOUR VEHICLE Remove the support rod from the hood, and insert it To open the tailgate, pull the release handle located on WARNING! into the radiator crossmember. the center of the tailgate and guide it to the lowered position.

  • Page 95: Closing

    GETTING TO KNOW YOUR VEHICLE NOTE: Failure to support the load at these two forward locations could result in damage. • Three 2x4 boards are needed to provide support at locations (1) and (2). Each board will need to be cut to fit inside the pickup box.

  • Page 96: Bed Rail Tie Down System - If Equipped

    GETTING TO KNOW YOUR VEHICLE BED RAIL TIE DOWN SYSTEM — TONNEAU COVER — IF EQUIPPED IF EQUIPPED The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather. The Tonneau Cover consists of the following features: CAUTION! •...
  • Page 97 GETTING TO KNOW YOUR VEHICLE 2. Using a #T50 Torx head driver, secure the fasteners 6. Position both Tonneau Cover latches over the lock- 7. Once the rear Tonneau Cover bar is positioned over to the bed. ing mechanisms (one on each side of the truck the locking mechanism, grab the back of the Ton- bed), making sure the plastic retainer is correctly neau Cover and push downward on the center to...

  • Page 98: Tonneau Cover Removal

    GETTING TO KNOW YOUR VEHICLE TONNEAU COVER REMOVAL To remove the Tonneau Cover, proceed as follows: 1. Open the tailgate. 2. Fold the rear panel of the Tonneau Cover forward to reveal the red release straps. Tonneau Cover With Tailgate In Mid-Position Roll Tonneau Cover Forward 8.

  • Page 99: Roof Luggage Rack - If Equipped

    GETTING TO KNOW YOUR VEHICLE Crossbars should always be used whenever cargo is CAUTION! placed on the roof rack. Check the straps frequently to be sure that the load remains securely attached. • Travel at reduced speeds and turn corners care- fully when carrying large or heavy loads on the roof NOTE: rack.

  • Page 100: Getting To Know Your Instrument Panel

    GETTING TO KNOW YOUR INSTRUMENT PANEL INSTRUMENT CLUSTERS...
  • Page 101 GETTING TO KNOW YOUR INSTRUMENT PANEL Use this QR code to access your digital experience. Scan me...

  • Page 102: Instrument Cluster Descriptions

    GETTING TO KNOW YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER panel, indicates how systems are operating and gives CAUTION! you warnings when a system, or systems, needs your DESCRIPTIONS attention. The steering wheel mounted controls allow Driving with a hot engine cooling system could dam- you to scroll through and enter the main menus and 1.

  • Page 103: Oil Life Reset - If Equipped

    GETTING TO KNOW YOUR INSTRUMENT PANEL Oil Life Reset • The main display area where the menus and pop-up They allow you to change the Main Screen area and messages are displayed. Menu Title area. 1. Without pushing the brake pedal, place the ignition Left And Right •...

  • Page 104: Instrument Cluster Display Selectable Items

    GETTING TO KNOW YOUR INSTRUMENT PANEL Adaptive Cruise Control (ACC) and Cruise Control are Speedometer Driver Assist — Messages Tire Pressure Monitor Coolant Temperature not available when using Off Road+. If either option is If Equipped System selected, a dedicated message will display indicating Vehicle Info Trip Info Screen Setup...
  • Page 105 GETTING TO KNOW YOUR INSTRUMENT PANEL NOTE: • The ACC screen may display once again if any ACC activ- Average – The display shows the average fuel ity occurs, which may include any of the following: economy (MPG, L/100km, or km/L) since the last When vehicle speed becomes too high to display the reset.

  • Page 106: Battery Saver On, Battery Saver Mode Message

    GETTING TO KNOW YOUR INSTRUMENT PANEL NOTE: Screen Setup Driver Selectable Items Current Gear • The call status will temporarily replace the previous Upper Left media source information displayed on the screen. • None Time Current Econ When the pop-up is no longer displayed, the display will Odometer Compass Range to Empty...

  • Page 107: Warning Lights And Messages

    GETTING TO KNOW YOUR INSTRUMENT PANEL • WARNING LIGHTS AND MESSAGES These messages indicate the vehicle battery has a low Unusual driving cycles (short trips separated by long state of charge and continues to lose electrical charge parking periods). at a rate that the charging system cannot sustain. •...
  • Page 108 GETTING TO KNOW YOUR INSTRUMENT PANEL Brake Warning Light Door Open Warning Light WARNING! This warning light monitors various brake This indicator will illuminate when a door is Driving a vehicle with the red brake light on is danger- functions, including brake fluid level and ajar/open and not fully closed.
  • Page 109 GETTING TO KNOW YOUR INSTRUMENT PANEL Hood Open Warning Light Seat Belt Reminder Warning Light NOTE: This light may turn on if the accelerator and brake ped- This indicator will illuminate when the hood This warning light indicates when the driver als are pressed at the same time.

  • Page 110: Yellow Warning Lights

    GETTING TO KNOW YOUR INSTRUMENT PANEL Vehicle Security Warning Light — tinue to drive normally. If Manual transmission detected in the ESC system. If this warning light equipped, this warning will illuminate to warn of high If Equipped remains on after several ignition cycles, and the vehicle clutch temperature.
  • Page 111 GETTING TO KNOW YOUR INSTRUMENT PANEL Loose Fuel Filler Cap Warning Light — Service 4WD Warning Light — Certain conditions, such as a loose or missing gas cap, If Equipped poor quality fuel, etc., may illuminate the light after If Equipped engine start.

  • Page 112: Yellow Indicator Lights

    GETTING TO KNOW YOUR INSTRUMENT PANEL Cruise Control Fault Warning Light Each tire, including the spare (if provided), should be vehicle that prevent the TPMS from functioning prop- checked monthly when cold and inflated to the inflation erly. Always check the TPMS malfunction telltale after This warning light will illuminate to indicate pressure recommended by the vehicle manufacturer on replacing one or more tires or wheels on your vehicle to...

  • Page 113: Green Indicator Lights

    GETTING TO KNOW YOUR INSTRUMENT PANEL 4WD Low Indicator Light — If Equipped Front And Rear Axle Lock Indicator Light Rear Axle Lock Indicator Light — — If Equipped If Equipped This light alerts the driver that the vehicle is in the 4WD Low mode.

  • Page 114: White Indicator Lights

    GETTING TO KNOW YOUR INSTRUMENT PANEL Adaptive Cruise Control (ACC) Set With Rear Seat Belt Fastened Indicator Light WHITE INDICATOR LIGHTS Target Indicator Light — If Equipped — If Equipped With A Premium Adaptive Cruise Control (ACC) Ready Instrument Cluster This will display when the ACC is set and a Indicator Light —...

  • Page 115: Blue Indicator Lights

    GETTING TO KNOW YOUR INSTRUMENT PANEL Rear Seat Belt Fastened Indicator Light Cruise Control Ready Indicator Light — BLUE INDICATOR LIGHTS — If Equipped With A Base Instrument If Equipped With A Premium Instrument High Beam Indicator Light Cluster Cluster This indicator light will illuminate to indicate This light indicates when a rear seat belt has This light will turn on when the cruise control...

  • Page 116: Onboard Diagnostic System (Obd Ii) Cybersecurity

    GETTING TO KNOW YOUR INSTRUMENT PANEL 2. As soon as you cycle the ignition switch to the ON WARNING! CAUTION! position, you will see the Malfunction Indicator Light ○ (MIL) symbol come on as part of a normal bulb Access, or allow others to access, information •...

  • Page 117: Starting And Operating

    STARTING AND OPERATING Four-Wheel Drive Models Only To Turn Off The Engine Using The ENGINE START/STOP STARTING THE ENGINE Button In 4L mode, if the vehicle is stalled, the engine will start regardless of whether or not the clutch pedal is pressed Before starting your vehicle, adjust your seat, adjust 1.

  • Page 118: Autopark

    STARTING AND OPERATING ENGINE START/STOP Button Functions — With Driver’s If the vehicle is not in PARK and the driver exits the WARNING! Foot Off The Brake Pedal (In PARK Or NEUTRAL vehicle with the engine running, the vehicle may Position) AutoPark.

  • Page 119: Extreme Cold Weather

    STARTING AND OPERATING EXTENDED PARK STARTING WARNING! WARNING! NOTE: • If vehicle speed is above 1.2 mph (1.9 km/h), the Never pour fuel or other flammable liquid into the transmission will default to NEUTRAL until the vehicle throttle body air inlet opening in an attempt to Extended Park condition occurs when the vehicle has speed drops below 1.2 mph (1.9 km/h).

  • Page 120: Engine Break-In Recommendations

    STARTING AND OPERATING • ENGINE BREAK-IN RECOMMENDATIONS PARKING BRAKE This light only shows that the parking brake is applied. It does not show the degree of brake application. A long break-in period is not required for the engine and Before exiting the vehicle, make sure that the parking When parking on a hill, it is important to turn the front drivetrain (transmission and axle) in your vehicle.

  • Page 121: Manual Transmission - If Equipped

    STARTING AND OPERATING To shift the gears, fully press the clutch pedal and place WARNING! CAUTION! the gear selector into the desired gear position (the • diagram for the engagement of the gears is displayed Always fully apply the parking brake when leaving •...

  • Page 122: Downshifting

    STARTING AND OPERATING Recommended Vehicle Shift Speeds To utilize your manual transmission efficiently for both fuel economy and performance, it should be upshifted as listed in the recommended shift speed chart. Shift at the vehicle speeds listed for acceleration. When heavily loaded or pulling a trailer, these recommended up shift speeds may not apply. Manual Transmission Shift Speeds in MPH (KM/H) Engine Speeds...

  • Page 123: Automatic Transmission - If Equipped

    STARTING AND OPERATING Manual Transmission Downshift Speeds in MPH (KM/H) Gear Selection 6 to 5 5 to 4 4 to 3 3 to 2 2 to 1 Maximum Speed 80 (129) 70 (113) 50 (81) 30 (48) 15 (24) NOTE: Vehicle speeds shown in the preceding chart are for 2H and 4H only, vehicle speeds in 4L would be significantly less.

  • Page 124: Ignition Park Interlock

    STARTING AND OPERATING 8–SPEED AUTOMATIC The transmission gear selector provides PARK, CAUTION! REVERSE, NEUTRAL, DRIVE and MANUAL (AutoStick) TRANSMISSION shift positions. Manual shifts can be made using the Damage to the transmission may occur if the follow- AutoStick shift control. Toggling the gear selector for- The transmission gear range (PRNDM) is displayed both ing precautions are not observed: ward (-) or rearward (+) while in the MANUAL (AutoStick)

  • Page 125: Gear Ranges

    STARTING AND OPERATING GEAR RANGES WARNING! WARNING! Do not press the accelerator pedal when shifting out of • • Your vehicle could move and injure you and others Never leave children alone in a vehicle, or with PARK or NEUTRAL. if it is not in PARK.
  • Page 126 STARTING AND OPERATING REVERSE (R) When frequent transmission shifting occurs (such as In the event of a momentary problem, the transmission when operating the vehicle under heavy loading condi- can be reset to regain all forward gears by performing This range is for moving the vehicle backward. Shift into tions, in hilly terrain, traveling into strong head winds, or the following steps: REVERSE only after the vehicle has come to a complete...

  • Page 127: Four-Wheel Drive Operation

    STARTING AND OPERATING AutoStick • If a requested downshift would cause the engine to FOUR-POSITION TRANSFER CASE — overspeed, that shift will not occur. IF EQUIPPED AutoStick is a driver-interactive transmission feature • The system will ignore attempts to upshift at too low providing manual shift control, giving you more control of a vehicle speed.
  • Page 128 STARTING AND OPERATING NOTE: N (Neutral) ing in the 4H and 4L positions on hard-surfaced roads will cause increased tire wear and damage to the drive- • Do not attempt to make a shift while only the front line components. For further information on shifting WARNING! or rear wheels are spinning.

  • Page 129: Five-Position Transfer Case - If Equipped

    STARTING AND OPERATING NOTE: N (Neutral) Shifting into or out of 4L is possible with the vehicle completely stopped; however, difficulty may occur due WARNING! to the mating teeth not being properly aligned. Several attempts may be required for clutch teeth alignment You or others could be injured or killed if you leave and shift completion to occur.
  • Page 130 STARTING AND OPERATING 2H/4H AUTO TO 4H PART TIME OR 4H PART 4H PART TIME/4H AUTO TO 4L OR 4L TO 4H In the event that additional traction is required, the transfer case 4H and 4L positions can be used to lock TIME TO 2H/4H AUTO PART TIME/4H AUTO the front and rear driveshafts together, forcing the front...

  • Page 131: Trac-Lok Rear Axle - If Equipped

    STARTING AND OPERATING TRAC-LOK REAR AXLE — The Axle Lock disengages at speeds above 30 mph (48 km/h), and will automatically re-lock once vehicle IF EQUIPPED speed is less than 10 mph (16 km/h). The Trac-Lok rear axle provides a constant driving force AXLE LOCK (TRU-LOK) REAR ONLY to both rear wheels and reduces wheel spin caused by the loss of traction at one driving wheel.

  • Page 132: Electronic Sway Bar Disconnect - If Equipped

    STARTING AND OPERATING This feature will only activate when the following condi- ELECTRONIC SWAY BAR WARNING! tions are met: DISCONNECT — IF EQUIPPED • Ignition in RUN position, vehicle in 4H (Four-Wheel Ensure the stabilizer/sway bar is reconnected before Drive High Range). Your vehicle may be equipped with an electronic discon- driving on hard surfaced roads or at speeds above necting stabilizer/sway bar.

  • Page 133: Off Road+ - If Equipped

    STARTING AND OPERATING NOTE: • Traction Control: High wheel speed, slip tuning brake WARNING! lock differential with no engine management OFF ROAD+ will not function in Two-Wheel Drive High • (2H) mode. If the button is pushed while in 2H mode, Electronic Stability Control: ESC Partial Off with If the stabilizer/sway bar will not return to on-road the cluster display will show the message “OFF ROAD+...

  • Page 134: Stop/Start System - Manual Transmission (If Equipped)

    STARTING AND OPERATING NOTE: If the “SERVICE POWER STEERING” message AUTOSTOP MODE and a flashing icon are displayed on the It is recommended that the Stop/Start system be dis- instrument cluster screen, it indicates that abled during off-road use. WARNING! the vehicle needs to be taken to an autho- Secondary Battery rized dealer for service.

  • Page 135: Possible Reasons The Engine Does Not

    STARTING AND OPERATING POSSIBLE REASONS THE ENGINE TO START THE ENGINE WHILE IN DOES NOT AUTOSTOP AUTOSTOP MODE Prior to engine shut down, the system will check many When the gear selector is in NEUTRAL, the engine will safety and comfort conditions to see if they are fulfilled. start when the clutch pedal is pressed (does not In following situations the engine will not stop: require complete/full pedal press).

  • Page 136: Stop/Start System - Automatic

    STARTING AND OPERATING To Activate The Autostop Mode, The Following Must STOP/START SYSTEM — AUTOMATIC Occur: TRANSMISSION (IF EQUIPPED) • The system must be in STOP/START READY state. A STOP/START READY message will be displayed in the instrument cluster display within the Stop/Start The Engine Stop/Start (ESS) function is developed to section page 100.

  • Page 137: To Start The Engine While In Autostop Mode

    STARTING AND OPERATING • • Engine has not reached normal operating HVAC system temperature or fan speed is manually TO MANUALLY TURN ON THE temperature adjusted STOP/START SYSTEM • • Engine or exhaust temperature is too high Battery voltage drops too low Push the Stop/Start Off switch (located on the switch •...

  • Page 138: Cruise Control

    STARTING AND OPERATING To Activate U.S. Speed (mph) CRUISE CONTROL Pushing the SET (+), or SET (-) button once will • Push the on/off button to activate the Cruise Control. When engaged, the Cruise Control system takes over result in a 1 mph speed adjustment. Each subse- The cruise indicator light in the instrument cluster dis- accelerator operations at speeds greater than 20 mph quent tap of the button results in an adjustment of...

  • Page 139: Adaptive Cruise Control (Acc)

    STARTING AND OPERATING ADAPTIVE CRUISE CONTROL (ACC) WARNING! WARNING! Adaptive Cruise Control (ACC) increases the driving con- • Cruise Control can be dangerous where the system Adaptive Cruise Control (ACC) is a convenience venience provided by Cruise Control while traveling on cannot maintain a constant speed.
  • Page 140 STARTING AND OPERATING Adaptive Cruise Control (ACC) Operation Adaptive Cruise Control Ready • When the parking brake is applied When ACC is activated, but the vehicle speed setting • When the automatic transmission is in PARK, The buttons on the right side of the steering wheel has not been selected, the display will read “Adaptive operate the ACC system.
  • Page 141 STARTING AND OPERATING To Set A Desired Speed NOTE: • The driver shifts to FIRST gear (manual transmission only) When the vehicle reaches the speed desired, push the • Keeping your foot on the accelerator pedal can • Vehicle is operating at a low RPM (manual transmis- SET (+) button or the SET (-) button and release.
  • Page 142 STARTING AND OPERATING Setting The Following Distance In ACC NOTE: Metric Speed (km/h) Pushing the SET (+), or SET (-) button once will • • The specified following distance for ACC can be set by While in ACC mode when the vehicle comes to a result in a 1 km/h speed adjustment.
  • Page 143 STARTING AND OPERATING Overtake Aid If there is no vehicle ahead, the vehicle will maintain WARNING! the set speed. If a slower moving vehicle is detected in When driving with ACC engaged and following a vehicle, the same lane, the instrument cluster displays the ACC When the ACC system is resumed, the driver must the system will provide an additional acceleration up to Set with Target Indicator Light, and the system adjusts...
  • Page 144 STARTING AND OPERATING “CLEAN FRONT WINDSHIELD” WARNING SERVICE ACC/FCW WARNING If weather conditions are not a factor, the driver should examine the sensor. It may require cleaning or removal The “ACC/FCW Limited Functionality Clean Front Wind- If the system turns off, and the instrument cluster dis- of an obstruction.
  • Page 145 STARTING AND OPERATING Offset Driving Condition Example ACC Hill Example Lane Changing Example TURNS AND BENDS LANE CHANGING NARROW VEHICLES When driving on a curve with ACC engaged, the system ACC may not detect a vehicle until it is completely in the Some narrow vehicles traveling near the outer edges of may increase or decrease the vehicle speed for stabil- lane in which you are traveling.

  • Page 146: Parksense Front/Rear Park Assist

    STARTING AND OPERATING STATIONARY OBJECTS AND VEHICLES ParkSense can be active only when the gear selector is PARKSENSE DISPLAY in REVERSE or DRIVE. If ParkSense is enabled at one of ACC does not react to stationary objects or vehicles. For The warning display will turn on indicating the system these gear selector positions, the system will remain example, ACC will not react in situations where the...
  • Page 147 STARTING AND OPERATING ParkSense Arcs 1 — No Tone/Solid Arc 6 — Fast Tone/Flashing Arc 2 — No Tone/Flashing Arc 7 — Fast Tone/Flashing Arc 3 — Fast Tone/Flashing Arc 8 — Slow Tone/Solid Arc 4 — Continuous Tone/Flashing Arc 9 —...
  • Page 148 STARTING AND OPERATING The vehicle is close to the obstacle when the display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert operation when the sys- tem is detecting an obstacle: WARNING ALERTS FOR REAR Greater than Rear Distance 79-59 inches...

  • Page 149: Enabling And Disabling Parksense

    STARTING AND OPERATING Front Park Assist Audible Alerts SERVICE THE PARKSENSE PARK CLEANING THE PARKSENSE ParkSense will turn off the Front Park Assist audible ASSIST SYSTEM SYSTEM alert (chime) after approximately three seconds when an obstacle has been detected, the vehicle is station- During vehicle start up, when the ParkSense system has Clean the ParkSense sensors with water, car wash soap, ary, and the brake pedal is applied.

  • Page 150: Parkview Rear Back Up Camera

    STARTING AND OPERATING • Clean the ParkSense sensors regularly, taking care PARKVIEW REAR BACK UP CAMERA WARNING! not to scratch or damage them. The sensors must not be covered with ice, snow, slush, mud, dirt or • Before using ParkSense, it is strongly recom- The ParkView Rear Back Up Camera allows you to see debris.
  • Page 151 STARTING AND OPERATING Zoom View Whenever the Rear View Camera image is activated WARNING! through the Back Up Camera button in the Controls When the Rear View Camera image is being displayed, menu, and the vehicle speed is greater than, or equal and the vehicle speed is below 8 mph (13 km/h) while Drivers must be careful when backing up even when to 8 mph (13 km/h), a display timer for the image is...

  • Page 152: Trailcam System - If Equipped

    STARTING AND OPERATING Cleaning The TrailCam TRAILCAM SYSTEM — IF EQUIPPED The TrailCam view can also be activated by pressing the icon on the Back Up Camera view. The Back Up Press and hold the Clean Camera button located on the Your vehicle may be equipped with a TrailCam that Camera view can also be activated by pressing the TrailCam view to wash the TrailCam.

  • Page 153: Loose Fuel Filler Cap Message

    STARTING AND OPERATING 2. Remove the fuel cap by rotating it counterclockwise. This might indicate a damaged cap. If the problem is CAUTION! detected twice in a row, the system will turn on the MIL. Resolving the problem will turn the MIL off. •...

  • Page 154: Trailer Towing

    STARTING AND OPERATING Gross Axle Weight Rating (GAWR) Loading TRAILER TOWING The GAWR is the maximum permissible load on the The actual total weight and the weight of the front and In this section you will find safety tips and information front and rear axles.
  • Page 155 STARTING AND OPERATING Gross Combination Weight Rating Weight-Carrying Hitch (GCWR) A weight-carrying hitch supports the trailer TW, just as if it were luggage located at a hitch ball or some other The GCWR is the total permissible weight of your connecting point of the vehicle.

  • Page 156: Trailer Hitch Classification

    STARTING AND OPERATING Recommended Distribution Hitch Adjustment 3. Attach the trailer to the vehicle without the weight distribution bars connected. 1. Position the truck to be ready to connect to the trailer (do not connect the trailer). 4. Measure the height from the top of the front fender to ground, this is height H2.

  • Page 157: Trailer Towing Weights (Maximum Trailer Weight Ratings)

    (805 km) the new vehicle is driven. The engine, collisions. axle or other parts could be damaged. • jeep.ca (Canada) • Then, during the first 500 miles (805 km) that a To locate your vehicle towing specs: Consider the following items when computing the...
  • Page 158 STARTING AND OPERATING • Check the trailer tires for proper tire inflation pres- WARNING! WARNING! sures before trailer usage. • • When hauling cargo or towing a trailer, do not over- Check for signs of tire wear or visible tire damage •...

  • Page 159: Towing Tips

    STARTING AND OPERATING Automatic Transmission — If Equipped NOTE: • Select the DRIVE range when towing. The transmission Disconnect the trailer wiring connector from the controls include a drive strategy to avoid frequent shift- vehicle (or any other device plugged into vehicle’s ing when towing.

  • Page 160: Recreational Towing (Behind Motorhome)

    STARTING AND OPERATING RECREATIONAL TOWING (BEHIND MOTORHOME) TOWING THIS VEHICLE BEHIND ANOTHER VEHICLE Towing Condition Wheels OFF the Ground Four-Wheel Drive Models See Instructions • Automatic transmission in PARK. • Flat Tow NONE Manual transmission in gear (NOT in NEUTRAL [N]). •...

  • Page 161: Driving Tips

    STARTING AND OPERATING Shifting Into N (Neutral) 8. Release the brake pedal (and clutch pedal on 7. Shift the transfer case lever to the desired position. manual transmissions) for five seconds and ensure NOTE: Use the following procedure to prepare your vehicle for that there is no vehicle movement.

  • Page 162: Off-Road Driving Tips

    STARTING AND OPERATING OFF-ROAD DRIVING TIPS 1. Loosen the two bolts that retain the GAWR bracket (Bolts #1 and #2) to the end cap using a T45 Torx Side Step Removal — If Equipped bit screwdriver. Do not remove the bolts. NOTE: Prior to off-road usage, the side steps should be removed to prevent damage.
  • Page 163 STARTING AND OPERATING The Basics Of Off-Road Driving When To Use 4L Range Driving In Snow, Mud And Sand You will encounter many types of terrain driving off- When off-road driving, shift into 4L for additional trac- SNOW road. You should be familiar with the terrain and area tion and control on slippery or difficult terrain, ascend- In heavy snow or for additional control and traction at before proceeding.
  • Page 164 STARTING AND OPERATING SAND CROSSING A RAVINE, GULLY, DITCH, WASH- forward until it makes contact with the object. Apply the throttle lightly while holding a light brake pressure and OUT OR RUT Soft sand is very difficult to travel through with full tire ease the vehicle up and over the object.
  • Page 165 STARTING AND OPERATING BEFORE CLIMBING A STEEP HILL CAUTION! WARNING! As you approach a hill, consider its grade or steepness. Do not attempt to cross a log with a greater diameter Never attempt to climb a hill at an angle or turn Determine if it is too steep.
  • Page 166 STARTING AND OPERATING Driving Through Water DRIVING ACROSS AN INCLINE BEFORE YOU CROSS ANY TYPE OF WATER Extreme care should be taken crossing any type of If at all possible, avoid driving across an incline. If it is As you approach any type of water, you need to deter- water.
  • Page 167 STARTING AND OPERATING After Driving Off-Road CROSSING DITCHES, STREAMS, SHALLOW WARNING! RIVERS OR OTHER FLOWING WATER Off-road operation puts more stress on your vehicle Abrasive material in any part of the brakes may cause than does most on-road driving. After going off-road, it Flowing water can be extremely dangerous.

  • Page 168: Multimedia

    MULTIMEDIA UCONNECT SYSTEMS Your Uconnect system may also have SCREEN OFF and WARNING! MUTE buttons on the faceplate. Push the SCREEN OFF button on the faceplate to turn • For detailed information about your Uconnect 5/5 NAV ONLY insert trusted media devices/components off the Uconnect screen.
  • Page 169 MULTIMEDIA NOTE: When making a selection, only press one button at a time to enter the desired menu. Once in the desired • Depending on the vehicle’s options, feature settings menu, press and release the preferred setting option may vary. until a check mark appears next to the setting, showing •...
  • Page 170 MULTIMEDIA Display When the Display button is pressed on the touchscreen, the system will display the options related to the theme (if equipped), brightness, and color of the touchscreen. The available settings are: NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Description Display Mode...
  • Page 171 MULTIMEDIA Units When the Units button is pressed on the touchscreen, the system displays the different measurement options. The selected unit of measurement will display in the instrument cluster display and Navigation system (if equipped). The available settings are: NOTE: Depending on the vehicle’s options, feature settings may vary.
  • Page 172 MULTIMEDIA Clock When the Clock button is pressed on the touchscreen, the system displays the different options related to the vehicle’s internal clock. NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Description Sync Time With GPS This setting will sync the time to the GPS receiver in the system.
  • Page 173 MULTIMEDIA Safety/Driving Assistance When the Safety/Driving Assistance button is selected on the touchscreen, the system displays the options related to the vehicle’s safety settings. These options will differ depending on the features equipped on the vehicle. The settings may display in list form or within subfolders on the screen. To access a subfolder, select the desired folder; the available options related to that feature will then display on the screen.
  • Page 174 MULTIMEDIA Mirrors & Wipers When the Mirrors & Wipers button is pressed on the touchscreen, the system displays the option related to the vehicle’s mirrors and wipers. NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Description Headlights With Wipers This setting will turn the headlights on when the wipers are activated.
  • Page 175 MULTIMEDIA Doors & Locks When the Doors & Locks button is pressed on the touchscreen, the system displays the options related to locking and unlocking the vehicle’s doors. NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Description Auto Unlock On Exit This setting will allow you to change if the doors lock automatically when the vehicle reaches 15 mph (24 km/h).
  • Page 176 MULTIMEDIA Seats & Comfort/Auto-On Comfort Systems When Seats & Comfort/Auto-On Comfort Systems button is pressed on the touchscreen, the system displays the options related to the vehicle’s comfort systems when remote start has been activated or the vehicle has been started. NOTE: Depending on the vehicle’s options, feature settings may vary.
  • Page 177 MULTIMEDIA Key Off Options/Engine Off Options When the Key Off Options/Engine Off Options button is pressed on the touchscreen, the system displays the options related to vehicle shutoff. These settings will only activate when the ignition is set to OFF. NOTE: Depending on the vehicle’s options, feature settings may vary.
  • Page 178 MULTIMEDIA Setting Name Description Equalizer This setting will adjust the “Bass”, “Mid”, and “Treble” ranges of the audio. Speed Adjusted Volume This setting will adjust audio volume as speeds increase. At a higher setting, the volume will increase more as the vehicle speeds up.
  • Page 179 MULTIMEDIA SiriusXM® Setup When the SiriusXM® Setup button is pressed on the touchscreen, the system displays options related to SiriusXM® satellite radio. These settings can be used to skip specific radio channels and restart favorite songs from the beginning. NOTE: •...
  • Page 180 MULTIMEDIA System Information When the System Information button is pressed on the touchscreen, the system displays the radio system information. NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Description Software Licenses This will display the software licensing information screen. Clear Personal Data After pressing the Clear Personal Data button on the touchscreen, the following setting will be available: NOTE:...

  • Page 181: Steering Wheel Audio Controls - If Equipped

    MULTIMEDIA STEERING WHEEL AUDIO CONTROLS — RADIO OPERATION REGULATORY AND SAFETY INFORMATION Pushing the top of the switch will seek up for the next IF EQUIPPED available station and pushing the bottom of the switch US/CANADA will seek down for the next available station. The remote sound system controls are located on the Exposure to Radio Frequency Radiation The button located in the center of the left-hand control...

  • Page 182: Vehicle Dynamics

    MULTIMEDIA VEHICLE DYNAMICS ACCESSORY GAUGE The Vehicle Dynamics page displays information con- The Accessory Gauge page displays the current status cerning the dynamics of the vehicle. of the vehicle’s Coolant Temperature, Oil Temperature, Oil Pressure (Gas Vehicles Only), Transmission Tem- The following information is displayed: perature (Automatic Transmissions Only), and Battery •...

  • Page 183: Trail Recording - If Equipped

    MULTIMEDIA • TRAIL RECORDING — IF EQUIPPED Places • Places Obstacles Guidance Obstacle Overview • Guidance Camping Bare Left The Trail Recording feature can be accessed from a NOTE: Scenic View Rock Bare Right variety of different ways: Within the Vehicle Dashboard A Waypoint can be placed whether or not the vehicle is Staging Area Sand...

  • Page 184: Adventure Guides - If Equipped

    “Delete All” towards the bottom of the summary of each trail and its difficulty level. touchscreen. Search For An Off-Road Trail NOTE: Saved recordings can be accessed even once the Jeep NOTE: connected services subscription has expired. ○ An active subscription to Jeep Connect con-...
  • Page 185 MULTIMEDIA Waypoints: The last page provides information on • different Waypoints along the trail such as distance from selected Waypoint and navigation routes to other Waypoints along the trail. NOTE: • “Trail Updated Successfully” will display towards the top of your touchscreen if the trail update was com- Expanded Trail Difficulty View Go Here Navigation Button pleted properly.
  • Page 186 MULTIMEDIA Preloaded Trails Press the Remove icon to remove a trail from the list. You will be presented with a confirmation, “Are you sure Press “Preloaded Trails” to see a list of trails that are you want to delete this trail?”. Press “Yes” to show the preloaded onto your Uconnect system.

  • Page 187: Safety

    SAFETY Anti-Lock Brake System (ABS) Warning SAFETY FEATURES WARNING! Light • The ABS contains sophisticated electronic equip- ANTI-LOCK BRAKE SYSTEM (ABS) The yellow ABS Warning Light will turn on when the igni- ment that may be susceptible to interference tion is placed in the ON/RUN mode and may stay on for caused by improperly installed or high output radio The ABS provides increased vehicle stability and brake as long as four seconds.

  • Page 188: Electronic Brake Control (Ebc) System

    SAFETY Hill Start Assist (HSA), and Traction Control System WARNING! WARNING! (TCS). These systems work together to enhance both vehicle stability and control in various driving • Before exiting a vehicle, always come to a com- The Brake Assist System (BAS) cannot prevent the conditions.
  • Page 189 SAFETY NOTE: ESC uses sensors in the vehicle to determine the WARNING! vehicle path intended by the driver and compares it to ERM is disabled any time the ESC is in “Full Off” mode the actual path of the vehicle. When the actual path •...
  • Page 190 SAFETY NOTE: If equipped with Off Road+ and if Off Road+ is active vehicle has been driven several miles (kilometers) at when "Full Off" mode is enabled by the driver, ESC will speeds greater than 30 mph (48 km/h), see an autho- For vehicles with multiple partial ESC modes, the push not switch to "Partial Off"...
  • Page 191 SAFETY Hill Start Assist (HSA) WARNING! WARNING! The HSA system is designed to mitigate roll back from a • HSA is not a parking brake. Always apply the park- There may be situations where the Hill Start Assist complete stop while on an incline. If the driver releases ing brake fully when exiting your vehicle.
  • Page 192 SAFETY NOTE: SSC has three states: The set speed for SSC is selectable by the driver, and can be adjusted by using the gear shift +/-. Additionally, • 1. Off (feature is not enabled and will not activate) During SSC, the +/- gear selector input is used for the SSC set speed may be reduced when climbing a SSC target speed selection but will not affect the 2.

  • Page 193: Auxiliary Driving Systems

    SAFETY Trailer Sway Control (TSC) Feedback To The Driver AUXILIARY DRIVING SYSTEMS The instrument cluster has an SSC icon and the SSC TSC uses sensors in the vehicle to recognize an exces- BLIND SPOT MONITORING (BSM) — switch has a light that offers feedback to the driver sively swaying trailer and will take the appropriate about the state SSC is in.
  • Page 194 SAFETY NOTE: Entering From The Side Vehicles that move into your adjacent lanes from either • The BSM system DOES NOT alert the driver about side of the vehicle. rapidly approaching vehicles that are outside the detection zones. • The BSM system detection zone DOES NOT change if your vehicle is towing a trailer.
  • Page 195 SAFETY Rear Cross Path (RCP) Overtaking Traffic The BSM system is designed not to issue an alert on stationary objects such as guardrails, posts, walls, foli- If you pass another vehicle slowly with a relative speed The RCP feature is intended to aid the driver when age, berms, etc.

  • Page 196: Forward Collision Warning (Fcw) With Mitigation - If Equipped

    SAFETY NOTE: FORWARD COLLISION WARNING WARNING! Whenever an audible alert is requested by the BSM (FCW) WITH MITIGATION — system, the radio is also muted. Rear Cross Path Detection (RCP) is not a backup aid IF EQUIPPED system. It is intended to be used to help a driver When the system is in RCP mode, the system shall detect an oncoming vehicle in a parking lot situation.
  • Page 197 SAFETY • When FCW status is set to “Warning and Braking”, WARNING! this allows the system to warn the driver of a pos- sible collision with the vehicle in front using audible/ Forward Collision Warning (FCW) is not intended to visual warnings and it applies autonomous braking.
  • Page 198 SAFETY Service FCW Warning NOTE: cyclist. If the PEB event stops the vehicle completely, the system will hold the vehicle at a standstill for two • If the system turns off, and the instrument cluster Changing the FCW status to “Only Warning” pre- seconds and then release the brakes.

  • Page 199: Tire Pressure Monitoring System (Tpms)

    SAFETY NOTE: The TPMS will continue to warn the driver of low tire CAUTION! pressure as long as the condition exists, and will not The PEB system will retain the last setting selected by turn off until the tire pressure is at or above the recom- the driver after ignition shut down.
  • Page 200 SAFETY NOTE: • Driving on a significantly underinflated tire causes Should this occur, you should stop as soon as possible the tire to overheat and can lead to tire failure. and inflate the tires with low pressure (those in a differ- It is particularly important for you to check the tire pres- Underinflation also reduces fuel efficiency and tire ent color in the instrument cluster graphic) to the vehi-...
  • Page 201 SAFETY TIRE FILL ALERT If the ignition is cycled, this sequence will repeat, pro- When Tire Fill Alert mode is entered, the tire pressure viding the system fault still exists. If the system fault no display screen will be displayed in the instrument This feature notifies the user when the placard tire longer exists, the TPMS Warning Light will no longer cluster.

  • Page 202: Occupant Restraint Systems

    SAFETY XX = the vehicle's cold placard pressure values for the (TPMS) sensor may be in an inoperative position, pre- Beginning with the next ignition cycle, the TPMS will no front and rear axles as shown on the vehicle placard venting the TPMS sensor signal from being received.

  • Page 203: Important Safety Precautions

    SAFETY Enhanced Seat Belt Use Reminder IMPORTANT SAFETY PRECAUTIONS 9. If the air bag system in this vehicle needs to be modified to accommodate a disabled person, see System (BeltAlert) Please pay close attention to the information in this page 298 for customer service contact Driver And Passenger BeltAlert (If Equipped) section.
  • Page 204 SAFETY Lap/Shoulder Belts repeat based on vehicle speed until the driver and WARNING! occupied outboard front seat passenger seat belts are All seating positions in your vehicle are equipped with buckled. The driver should instruct all occupants to • Wearing your seat belt incorrectly could make your lap/shoulder belts.
  • Page 205 SAFETY Lap/Shoulder Belt Operating WARNING! Instructions • A seat belt that is too loose will not protect you 1. Enter the vehicle and close the door. Sit back and properly. In a sudden stop, you could move too far forward, increasing the possibility of injury. Wear adjust the seat.
  • Page 206 SAFETY Adjustable Upper Shoulder Belt NOTE: 5. Position the shoulder belt across the shoulder and chest with minimal, if any slack so that it is comfort- Anchorage The adjustable upper shoulder belt anchorage is able and not resting on your neck. The retractor will equipped with an Easy Up feature.
  • Page 207 SAFETY Switchable Automatic Locking Retractor Position the lap belt snug and low below the abdomen WARNING! and across the strong bones of the hips. Place the (ALR) shoulder belt across the chest and away from the neck. • ONLY use a Seat Belt Extender if it is physically The seat belts in the passenger seating positions are Never place the shoulder belt behind the back or under required in order to properly fit the original seat...
  • Page 208 SAFETY How To Disengage The Automatic Locking Mode In Automatic Locking Mode, the shoulder belt is auto- matically pre-locked. The seat belt will still retract to Unbuckle the combination lap/shoulder belt and allow remove any slack in the shoulder belt. Use the Auto- it to retract completely to disengage the Automatic matic Locking Mode anytime a child restraint is Locking Mode and activate the vehicle sensitive (emer-...

  • Page 209: Supplemental Restraint Systems (Srs)

    SAFETY Air Bag Warning Light NOTE: SUPPLEMENTAL RESTRAINT If the speedometer, tachometer, or any engine related SYSTEMS (SRS) The Occupant Restraint Controller (ORC) gauges are not working, the Occupant Restraint Control- monitors the readiness of the electronic Some of the safety features described in this section ler (ORC) may also be disabled.
  • Page 210 SAFETY Front Air Bags This vehicle may be equipped with a driver and/or front WARNING! passenger seat belt buckle switch that detects whether This vehicle has front air bags and lap/shoulder belts the driver or front passenger seat belt is buckled. The •...
  • Page 211 SAFETY The Occupant Classification System (OCS) Consists Of Because air bag sensors measure vehicle deceleration WARNING! The Following: over time, vehicle speed and damage by themselves are not good indicators of whether or not an air bag • • Occupant Restraint Controller (ORC) No objects should be placed over or near the air should have deployed.
  • Page 212 SAFETY The OCS may deactivate the deployment of the Passen- ger Advanced Front Air Bag if the OCS estimates that: • The front passenger seat is unoccupied or has very light objects in it. • The front passenger seat is occupied by a rear- facing child restraint.
  • Page 213 SAFETY The PAD Indicator Light should be illuminated and the 4. Have the adult passenger sit in the center of the WARNING! Passenger Advanced Front Air Bag should be deacti- seat, with the passenger’s feet comfortably on or vated for most properly seated and restrained children near the floor, and with their back against the •...
  • Page 214 SAFETY Lighter Weight Passengers (Including Small Adults) front passenger seat may result in activation of the Pas- senger Advanced Front Air Bag. Examples of improper When a lighter weight passenger, including a small front passenger seating include: adult, occupies the passenger seat, the Passenger •...
  • Page 215 SAFETY WARNING! WARNING! • • If a child restraint system, child, small teenager or Ignoring the Air Bag Warning Light in your instru- adult in the front passenger seat is seated improp- ment panel could mean you won’t have the air erly, the occupant may provide an output signal to bags to protect you in a collision.
  • Page 216 SAFETY Knee Impact Bolsters The following requirements must be strictly followed: • Do not modify the front passenger seat assembly or The Knee Impact Bolsters help protect the knees of the components in any way. driver and front passenger, and position the front occu- •...
  • Page 217 SAFETY Supplemental Side Air Bag Inflatable Curtains The SABICs may help reduce the risk of partial or com- The Side Air Bags will not deploy in all side collisions, (SABICs) plete ejection of vehicle occupants through side win- including some collisions at certain angles, or some dows in certain side impact events.
  • Page 218 SAFETY • Front and Side Impact Sensors Do not drive your vehicle after the air bags have WARNING! deployed. If you are involved in another collision, the air • Seat Belt Pretensioners bags will not be in place to protect you. •...
  • Page 219 SAFETY Enhanced Accident Response System Your vehicle may also be designed to perform any of WARNING! these other functions in response to the Enhanced Acci- Reset Procedure dent Response System: • Do not attempt to modify any part of your air bag In order to reset the Enhanced Accident Response Sys- •...

  • Page 220: Child Restraints

    SAFETY NOTE: WARNING! EDR data are recorded by your vehicle only if a non- trivial crash situation occurs; no data are recorded by In a collision, an unrestrained child can become a the EDR under normal driving conditions and no per- projectile inside the vehicle.
  • Page 221 SAFETY Summary Of Recommendations For Restraining Children In Vehicles Child Size, Height, Weight Or Age Recommended Type Of Child Restraint Children who are two years old or younger and who have not reached Either an Infant Carrier or a Convertible Child Restraint, facing rear- Infants and Toddlers the height or weight limits of their child restraint ward in a rear seat of the vehicle...
  • Page 222 SAFETY Children Too Large For Booster Seats If the answer to any of these questions was “no,” then WARNING! the child still needs to use a booster seat in this Children who are large enough to wear the shoulder vehicle. If the child is using the lap/shoulder belt, check •...
  • Page 223 SAFETY Lower Anchors And Tethers For CHildren LATCH Positions For Installing Child (LATCH) Restraints In This Vehicle LATCH Label Your vehicle is equipped with the child restraint anchor- LATCH Positions age system called LATCH, which stands for Lower Anchors and Tethers for CHildren. The LATCH system Lower Anchorage Symbol (2 Anchorages Per Seat- has three vehicle anchor points for installing LATCH- ing Position)
  • Page 224 SAFETY Frequently Asked Questions About Installing Child Restraints With LATCH Use the LATCH anchorage system until the combined weight of the What is the weight limit (child’s weight + weight of the child restraint) child and the child restraint is 65 lb (29.5 kg). Use the seat belt and 65 lb (29.5 kg) for using the LATCH anchorage system to attach the child restraint? tether anchor instead of the LATCH system once the combined...
  • Page 225 SAFETY Locating The LATCH Anchorages WARNING! The lower anchorages are round bars that Never use the same lower anchorage to attach more are found at the rear of the seat cushion than one child restraint. If you are installing LATCH- where it meets the seatback, adjacent to the compatible child restraints next to each other, you anchorage symbols on the seatback.
  • Page 226 SAFETY 3. Attach the lower hooks or connectors of the child bing retract back into the retractor. If it is locked, the WARNING! restraint to the lower anchorages in the selected ALR will make a clicking noise while the webbing is seating position.
  • Page 227 SAFETY Frequently Asked Questions About Installing Child Restraints With Seat Belts What is the weight limit (child’s weight + weight of the child restraint) Always use the tether anchor when using the seat belt to install a for using the Tether Anchor with the seat belt to attach a forward- Weight limit of the Child Restraint forward-facing child restraint, up to the recommended weight limit of facing child restraint?

  • Page 228: Safety Tips

    SAFETY Installing Child Restraints Using The Top 3. Route the tether strap to provide the most direct WARNING! Tether Anchorage path between the anchorage and the child seat. The tether strap should go between the head restraint • An incorrectly anchored tether strap could lead to posts underneath the head restraint.

  • Page 229: Transporting Pets

    SAFETY Floor Mat Safety Information TRANSPORTING PETS SAFETY CHECKS YOU SHOULD MAKE INSIDE THE VEHICLE Always use floor mats designed to fit your vehicle. Only Air Bags deploying in the front seat could harm your use a floor mat that does not interfere with the opera- pet.

  • Page 230: Periodic Safety Checks You Should Make Outside The Vehicle

    SAFETY PERIODIC SAFETY CHECKS YOU EXHAUST GAS WARNING! SHOULD MAKE OUTSIDE THE • ONLY use the driver’s side floor mat on the driver’s WARNING! VEHICLE side floor area. To check for interference, with the vehicle properly parked with the engine off, fully Exhaust gases can injure or kill.

  • Page 231: Carbon Monoxide Warnings

    SAFETY CARBON MONOXIDE WARNINGS WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon mon- oxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill.

  • Page 232: In Case Of Emergency

    Push the button to turn on the Hazard Warning Flash- Assist And SOS Buttons operable if your Jeep Connect service is active and ers. When the button is activated, all directional turn you are connected to an operable LTE (voice/data) signals will flash on and off to warn oncoming traffic of 1 —...
  • Page 233 IN CASE OF EMERGENCY • Jeep Connect Customer Care – In-vehicle support WARNING! WARNING! for Jeep Connect. • Vehicle Customer Care – Total support for all other • ALWAYS obey traffic laws and pay attention to the If anyone in the vehicle could be in danger (e.g., vehicle issues.
  • Page 234 IN CASE OF EMERGENCY NOTE: SOS Call System Limitations Even if the SOS Call system is fully functional, factors Vehicles sold in Mexico DO NOT have SOS Call system beyond FCA US LLC’s control may prevent or stop the • Your vehicle may be transmitting data as authorized SOS Call system operation.

  • Page 235: Jacking And Tire Changing

    IN CASE OF EMERGENCY NOTE: JACKING AND TIRE CHANGING PREPARATIONS FOR JACKING Passengers should not remain in the vehicle when the 1. Park on a firm, level surface. Avoid ice or slippery Use this QR code to access your digital vehicle is being jacked in position.
  • Page 236 IN CASE OF EMERGENCY NOTE: See the following steps to remove: 4. Remove tool kit and assemble tools. If the tailgate is lowered, the jack extension with hook 1. Fold up the right rear seat. can be added to this assembly to enable lowering of the 2.

  • Page 237: Spare Tire Location And Removal

    IN CASE OF EMERGENCY For spare tire removal, see the following steps: WARNING! 1. Locate the winch access hole at the rear of the After using the jack and tools, always reinstall them in vehicle. the original carrier and location. While driving you may experience abrupt stopping, rapid acceleration or sharp turns.

  • Page 238: Jacking Instructions

    IN CASE OF EMERGENCY JACKING INSTRUCTIONS WARNING! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle.
  • Page 239 IN CASE OF EMERGENCY NOTE: Keep the jack and tools aligned while raising the vehicle to prevent tool damage. Assembled Jack And Tools Rear Jacking Location 4. Operate the jack from the front or the rear of the CAUTION! vehicle. Place the jack under the axle tube, as Front Jacking Location shown.

  • Page 240: To Stow The Flat Or Spare

    IN CASE OF EMERGENCY 8. Install the lug nuts with the cone-shaped end toward TO STOW THE FLAT OR SPARE the wheel. Lightly tighten the lug nuts clockwise. See the following steps for stowing the flat or spare tire: WARNING! 1.

  • Page 241: Reinstalling The Jack And Tools

    IN CASE OF EMERGENCY REINSTALLING THE JACK AND TOOLS 1. Position the jack and tool bag. Make sure the lug wrench is under the jack near the jack turn-screw. Reinstalling The Flat Or Spare Tire Jack Hold Down Wing Bolt WARNING! WARNING! A loose tire or jack thrown forward in a collision or...

  • Page 242: Jump Starting

    IN CASE OF EMERGENCY JUMP STARTING PREPARATIONS FOR JUMP START The battery in your vehicle is located in the right rear of the engine compartment. If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.

  • Page 243: Jump Starting Procedure

    IN CASE OF EMERGENCY NOTE: WARNING! WARNING! Make sure at all times that unused ends of jumper cables are not contacting each other or either vehicle Do not connect the jumper cable to the negative (-) • Do not allow vehicles to touch each other as this while making connections.

  • Page 244: If Your Engine Overheats

    IN CASE OF EMERGENCY If frequent jump starting is required to start your vehicle In the event it is observed that the temperature gauge WARNING! you should have the battery and charging system tested is moving towards or close to the HOT (H) position, you at an authorized dealer.

  • Page 245: Freeing A Stuck Vehicle

    IN CASE OF EMERGENCY To Reset The Manual Park Release: NOTE: 1. Pull upward on the tether strap, releasing it from the • For vehicles with automatic transmission: Shifts “locked” position. between DRIVE (D) and REVERSE (R) can only be achieved at wheel speeds of 5 mph (8 km/h) or 2.

  • Page 246: Towing A Disabled Vehicle

    IN CASE OF EMERGENCY CAUTION! • Racing the engine or spinning the wheels may lead to transmission overheating and failure. Allow the engine to idle with the transmission in NEUTRAL (N) for at least one minute after every five rocking-motion cycles. This will minimize overheating and reduce the risk of clutch or transmission failure during prolonged efforts to free a stuck vehicle.

  • Page 247: Four-Wheel Drive Models

    IN CASE OF EMERGENCY WITHOUT THE KEY FOB CAUTION! Special care must be taken when the vehicle is towed • Do not use sling type equipment when towing. with the ignition in the OFF position. The only approved Vehicle damage may occur. method of towing without the key fob is with a flatbed •...

  • Page 248: Enhanced Accident Response System (Ears)

    IN CASE OF EMERGENCY CAUTION! • Tow hooks are for emergency use only, to rescue a vehicle stranded off road. Tow straps are recom- mended when towing the vehicle, chains may cause vehicle damage. • The tow hooks must not be used to move the vehicle off the road or where there are obstacles.

  • Page 249: Servicing And Maintenance

    SERVICING AND MAINTENANCE NOTE: SCHEDULED SERVICING On vehicles equipped with an instrument cluster dis- play, “Oil Change Required” will be displayed and a Under no circumstances should oil change intervals single chime will sound, indicating that an oil change is exceed 10,000 miles (16,000 km), 12 months or Your vehicle is equipped with an automatic oil change necessary.
  • Page 250 SERVICING AND MAINTENANCE Mileage Or Time Passed (Whichever Comes First) Or Years: Or Kilometers: Additional Inspections Inspect the CV/Universal joints. Inspect front suspension, rear suspension, tie rod ends, and replace if necessary. Inspect the front and rear axle fluid. Inspect the brake linings, replace as necessary.
  • Page 251 SERVICING AND MAINTENANCE Mileage Or Time Passed (Whichever Comes First) Or Years: Or Kilometers: Change the manual transmission fluid if using your vehicle for any of the following: trailer towing, snow plowing, heavy loading, taxi, police, delivery service (commercial service), off-road, desert operation or more than 50% of your driving is at sustained high speeds during hot weather, above 90°F (32°C).

  • Page 252: Engine Compartment

    SERVICING AND MAINTENANCE ENGINE COMPARTMENT 3.6L ENGINE 1 — Power Distribution Center (Fuses) 6 — Brake Fluid Reservoir Cap 2 — Battery 7 — Engine Air Cleaner, Filter 3 — Engine Oil Dipstick 8 — Power Steering Fluid Reservoir Cap 4 —...

  • Page 253: Checking Oil Level

    SERVICING AND MAINTENANCE CHECKING OIL LEVEL ADDING WASHER FLUID WARNING! To ensure proper engine lubrication, the engine oil must The fluid reservoir is located in the engine compart- • Battery gas is flammable and explosive. Keep be maintained at the correct level. Check the oil level at ment.

  • Page 254: Pressure Washing

    SERVICING AND MAINTENANCE NOTE: CAUTION! CAUTION! Intentional tampering with emissions control systems • Vehicles with the Stop/Start system will be may void your warranty and could result in civil penal- Do not use chemical flushes in your engine oil as the equipped with two batteries.

  • Page 255: Engine Oil Filter

    SERVICING AND MAINTENANCE ENGINE OIL FILTER 2. Lift the engine air cleaner filer cover to access the CAUTION! engine air cleaner, filter. The engine oil filter should be replaced with a new filter • Many aftermarket performance air filter elements do at every engine oil change.

  • Page 256: Accessory Drive Belt Inspection

    SERVICING AND MAINTENANCE ACCESSORY DRIVE BELT AIR CONDITIONER MAINTENANCE INSPECTION For best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service WARNING! should include cleaning of the condenser fins and a performance test.
  • Page 257 SERVICING AND MAINTENANCE Refrigerant Recovery And Recycling R-1234yf R-1234yf Air Conditioning Refrigerant is a Hydrofluo- roolefin (HFO) that is endorsed by the Environmental Protection Agency and is an ozone-friendly substance with a low global-warming potential. The manufacturer recommends that air conditioning service be performed by an authorized dealer using recovery and recycling equipment.

  • Page 258: Body Lubrication

    SERVICING AND MAINTENANCE Wiper Blade Removal/Installation The external lock cylinders should be lubricated twice a year, preferably in the Autumn and Spring. Apply a small amount of a high quality lubricant, such as Mopar® CAUTION! Lock Cylinder Lubricant, directly into the lock cylinder. Do not allow the wiper arm to spring back against the WINDSHIELD WIPER BLADES glass without the wiper blade in place or the glass...

  • Page 259: Exhaust System

    SERVICING AND MAINTENANCE EXHAUST SYSTEM CAUTION! The best protection against carbon monoxide entry into • The catalytic converter requires the use of the vehicle body is a properly maintained engine unleaded fuel only. Leaded gasoline will destroy exhaust system. the effectiveness of the catalyst as an emissions If you notice a change in the sound of the exhaust sys- control device, may seriously reduce engine perfor- tem, or if the exhaust fumes can be detected inside the...

  • Page 260: Cooling System

    SERVICING AND MAINTENANCE Coolant Checks Selection Of Coolant To minimize the possibility of catalytic converter damage: Check the engine coolant (antifreeze) protection every For further information page 296. • Do not interrupt the ignition when the transmission 12 months (before the onset of freezing weather, where NOTE: is in gear and the vehicle is in motion.
  • Page 261 SERVICING AND MAINTENANCE Adding Coolant NOTE: WARNING! Your vehicle has been built with an improved engine • It is the owner's responsibility to maintain the proper • Do not use a pressure cap other than the one coolant (OAT coolant conforming to MS.90032) that level of protection against freezing according to the specified for your vehicle.

  • Page 262: Brake System

    SERVICING AND MAINTENANCE Cooling System Notes BRAKE SYSTEM WARNING! In order to ensure brake system performance, all brake NOTE: • Use only manufacturer recommended brake fluid. system components should be inspected periodically. When the vehicle is stopped after a few miles/ Using the wrong type of brake fluid can severely For the proper maintenance intervals page 247.

  • Page 263: Front/Rear Axle Fluid

    SERVICING AND MAINTENANCE Frequency Of Fluid Change FRONT/REAR AXLE FLUID Under normal operating conditions, the fluid installed at For normal service, periodic fluid level checks are not the factory will give satisfactory lubrication for the life of required. When the vehicle is serviced for other reasons the vehicle.

  • Page 264: Fuses

    SERVICING AND MAINTENANCE Fluid Level Check NOTE: WARNING! No chemical flushes should be used in any transmis- The fluid level is preset at the factory and does not • sion; only the approved lubricant should be used. If a general protection fuse for safety systems (air require adjustment under normal operating conditions.
  • Page 265 SERVICING AND MAINTENANCE Power Distribution Center (PDC) The Power Distribution Center is located in the engine compartment near the battery. This center contains cartridge fuses, mini fuses, and relays. The PDC top cover is labeled with each serviceable fuse/relay loca- tion, function, and size.
  • Page 266 SERVICING AND MAINTENANCE Power Distribution Center Location...
  • Page 267 SERVICING AND MAINTENANCE Cavity Cartridge Fuse Micro Fuse Description * If Equipped – – Spare * 40 Amp Green – Starter – 5 Amp Tan Intelligent Battery Sensor (IBS) – 20 Amp Yellow Fuel Pump MTR/FPCM – 5 Amp Tan Security Gateway –...
  • Page 268 SERVICING AND MAINTENANCE Cavity Cartridge Fuse Micro Fuse Description * If Equipped – 10 Amp Red Module Shift By Wire (MOD_SBW) 40 Amp Green – Central Body Controller (CBC) 2-EXTERIOR LIGHTS #1 30 Amp Pink – Front Wipers 40 Amp Green –...
  • Page 269 SERVICING AND MAINTENANCE Cavity Cartridge Fuse Micro Fuse Description * If Equipped – – Spare * – – Spare * – 10 Amp Red Occupant Restraint Controller (ORC) – 10 Amp Red HD ACC * Humidity Light Rain Sensor (HLRS)/Inverter 400W Wake Up/USB/ –...
  • Page 270 SERVICING AND MAINTENANCE Cavity Cartridge Fuse Micro Fuse Description * If Equipped – 10 Amp Red HD ELEC ACC PKG * – – Spare * – – Spare * – – Spare * – 20 Amp Yellow – 10 Amp Red Heated Mirrors –...
  • Page 271 SERVICING AND MAINTENANCE Cavity Cartridge Fuse Micro Fuse Description * If Equipped – – Spare * – 10 Amp Red PWR MIRROR SW – 20 Amp Yellow RADIO – 10 Amp Red SW BANK-HD ELEC/OFF ROAD – – Spare * F100 30 Amp Pink –...

  • Page 272: Bulb Replacement

    SERVICING AND MAINTENANCE BULB REPLACEMENT Replacement Bulbs, Names, And Part Numbers In the instance a bulb needs to be replaced, this section includes bulb description and replacement part numbers. NOTE: See an authorized dealer for LED bulb replacement. Interior Bulbs Bulb Name Bulb Number Automatic Transmission Indicator Lamp...
  • Page 273 SERVICING AND MAINTENANCE Exterior Bulbs Bulb Name Bulb Number Rear Base Tail Lamp Stop/Tail/Turn Bulb 3157 Rear Base Tail Lamp Backup Bulb 7440 Rear Base Tail Lamp Side Marker Center High Mounted Stop Lamp License Lamp NOTE: Numbers refer to commercial bulb types that can be purchased from an authorized dealer. If a bulb needs to be replaced, visit an authorized dealer or refer to the applicable Service Manual.
  • Page 274 SERVICING AND MAINTENANCE FRONT PARK/TURN SIGNAL FRONT FOG LAMP — IF EQUIPPED REAR TAIL, STOP, TURN SIGNAL, AND BACKUP LAMP — IF EQUIPPED See the following steps to replace: See the following steps to replace: See the following steps to replace: 1.

  • Page 275: Tires

    SERVICING AND MAINTENANCE NOTE: NOTE: CAUTION! If your vehicle is equipped with bead-lock wheels, • P (Passenger) — Metric tire sizing is based on US please refer to your vehicles bead-lock specific part • Do not touch the new bulb with your fingers. Oil design standards.
  • Page 276 SERVICING AND MAINTENANCE TIRE SIZING CHART EXAMPLE: Example Size Designation: P215/65R15XL 95H, 215/65R15 96H, LT235/85R16C, T145/80D18 103M, 31x10.5 R15 LT P = Passenger car tire size based on US design standards, or "..blank.." = Passenger car tire based on European design standards, or LT = Light truck tire based on US design standards, or T or S = Temporary spare tire, or 31 = Overall diameter in inches (in)
  • Page 277 SERVICING AND MAINTENANCE Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire; however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire.
  • Page 278 SERVICING AND MAINTENANCE Tire Loading And Tire Pressure This placard tells you important information about the: 1. Number of people that can be carried in the vehicle. NOTE: 2. Total weight your vehicle can carry. The proper cold tire inflation pressure is listed on the driver’s side B-pillar or the rear edge of the driver's side 3.
  • Page 279 SERVICING AND MAINTENANCE Steps For Determining Correct Load (6) If your vehicle will be towing a Limit— trailer, load from your trailer will be transferred to your vehicle. Consult (1) Locate the statement “The com- this manual to determine how this bined weight of occupants and cargo reduces the available cargo and lug- should never exceed XXX kg or...
  • Page 280 SERVICING AND MAINTENANCE WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them.

  • Page 281: Tires - General Information

    SERVICING AND MAINTENANCE TIRES — GENERAL INFORMATION Both underinflation and overinflation affect the stability CAUTION! of the vehicle and can produce a feeling of sluggish Tire Pressure response or over responsiveness in the steering. After inspecting or adjusting the tire pressure, always reinstall the valve stem cap.
  • Page 282 SERVICING AND MAINTENANCE Tire Pressures For High Speed Operation NOTE: Tire Repair TPMS sensor must be replaced after driving the vehicle If your tire becomes damaged, it may be repaired if it The manufacturer advocates driving at safe speeds and on a flat tire condition.
  • Page 283 SERVICING AND MAINTENANCE Tread Wear Indicators • Distance driven See the Tire Sizing Chart found in the “Tire Safety Infor- mation” section of this manual for more information • Performance tires, tires with a speed rating of V or Tread wear indicators are in the original equipment relating to the Load Index and Speed Symbol of a tire higher, and Summer tires typically have a reduced tires to help you in determining when your tires should...

  • Page 284: Tire Types

    SERVICING AND MAINTENANCE Summer tires do not contain the all season designation SPARE TIRES — IF EQUIPPED WARNING! or mountain/snowflake symbol on the tire sidewall. Use • Summer tires only in sets of four; failure to do so may NOTE: Failure to equip your vehicle with tires having adversely affect the safety and handling of your vehicle.

  • Page 285: Wheel And Wheel Trim Care

    SERVICING AND MAINTENANCE Limited Use Spare — If Equipped Since this tire has limited tread life, the original equip- Your wheels are susceptible to deterioration caused by ment tire should be repaired (or replaced) and rein- salt, sodium chloride, magnesium chloride, calcium The limited use spare tire is for temporary emergency stalled on your vehicle at the first opportunity.

  • Page 286: Snow Traction Devices

    SERVICING AND MAINTENANCE NOTE: SNOW TRACTION DEVICES If you intend parking or storing your vehicle for an Use of traction devices require sufficient tire-to-body extended period after cleaning the wheels with wheel clearance. Due to limited clearance, the following snow cleaner, drive your vehicle and apply the brakes to traction devices are recommended.

  • Page 287: Tire Rotation Recommendations

    SERVICING AND MAINTENANCE TIRE ROTATION WARNING! CAUTION! RECOMMENDATIONS Using tires of different size and type (M+S, Snow) Proper operation of four-wheel drive vehicles depends The tires on the front and rear of your vehicle operate between front and rear axles can cause unpredict- on tires of equal size, type, and circumference on at different loads and perform different steering, han- able handling.

  • Page 288: Treadwear

    SERVICING AND MAINTENANCE TREADWEAR 109. Grades B and A represent higher WARNING! levels of performance on the labora- The Treadwear grade is a comparative The traction grade assigned to this tory test wheel, than the minimum rating, based on the wear rate of the tire is based on straight-ahead brak- required by law.

  • Page 289: Bodywork

    SERVICING AND MAINTENANCE BODYWORK WARNING! • Vehicles with the Stop/Start system will be PROTECTION FROM ATMOSPHERIC equipped with two batteries. Both the main and the supplemental batteries must be disconnected AGENTS to completely de-energize the 12 Volt electrical Vehicle body care requirements vary according to geo- system.

  • Page 290: Body And Underbody Maintenance

    SERVICING AND MAINTENANCE Appearance Care For Fabric Top Models BODY AND UNDERBODY CAUTION! MAINTENANCE To maintain the appearance of your vehicle's interior • Do not use abrasive or strong cleaning materials, trim and top, follow these precautions: Cleaning Headlights such as steel wool or scouring powder, that will •...

  • Page 291: Interiors

    Only operate the vehicle when the • dow, not up and down. Mopar® Jeep® Soft Glass carpet is securely attached by the grommets so it can- It is recommended that the top be free of water prior to opening it.

  • Page 292: Carpet Removal

    SERVICING AND MAINTENANCE 2. Pull the carpet out from the front to the rear. 4. Under the back of the front seat, open the carpet WARNING! split and then pull out the rear edge and slide the • carpet to the front (do not remove the harness). ONLY install carpet designed to fit your vehicle.

  • Page 293: Seats And Fabric Parts

    SERVICING AND MAINTENANCE Seat Belt Maintenance Rear Carpet 1. Remove the grommets under the front seat (one left and one right). CAUTION! Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric.

  • Page 294: Plastic And Coated Parts

    SERVICING AND MAINTENANCE PLASTIC AND COATED PARTS liquid. Please do not use polishes, oils, cleaning fluids, solvents, detergents, or ammonia-based cleaners to Use Mopar® Total Clean to clean vinyl upholstery. clean your leather upholstery. NOTE: CAUTION! If equipped with light colored leather, it tends to show •...

  • Page 295: Technical Specifications

    TECHNICAL SPECIFICATIONS VEHICLE IDENTIFICATION NUMBER (VIN) In the event power assist is lost for any reason (i.e., repeated brake applications with the engine off) the brakes will still function. However, the effort required to The VIN is found on the left front corner of the A-pillar, brake the vehicle will be much greater than that visible from outside of the vehicle through the required with the power system operating.

  • Page 296: Fuel Requirements

    TECHNICAL SPECIFICATIONS After 25 miles (40 km), check the lug nut/bolt torque to REFORMULATED GASOLINE CAUTION! be sure that all the lug nuts/bolts are properly seated Many areas of the country require the use of cleaner- against the wheel. DO NOT use E-85, gasoline containing methanol, or burning gasoline referred to as “reformulated gasoline”.

  • Page 297: Compressed Natural Gas (Cng) And Liquid Propane (Lp) Fuel System Modifications

    TECHNICAL SPECIFICATIONS COMPRESSED NATURAL GAS (CNG) FUEL SYSTEM CAUTIONS AND LIQUID PROPANE (LP) FUEL CAUTION! SYSTEM MODIFICATIONS Follow these guidelines to maintain your vehicle’s Modifications that allow the engine to run on CNG or LP performance: may result in damage to the engine, emissions, and •...

  • Page 298: Fluid Capacities

    TECHNICAL SPECIFICATIONS FLUID CAPACITIES Metric Fuel (Approximate) 22.0 gal 83.0 L Engine Oil with Filter 3.6L Engine 5.0 qt 4.7 L Cooling System * 3.6L Engine 13.0 qt 12.3 L *Includes coolant recovery bottle filled to MAX level. ENGINE FLUIDS AND LUBRICANTS Component Fluid, Lubricant, or Genuine Part We recommend using Mopar®...

  • Page 299: Chassis Fluids And Lubricants

    TECHNICAL SPECIFICATIONS CHASSIS FLUIDS AND LUBRICANTS Component Fluid, Lubricant, or Genuine Part Use only Mopar® ZF 8 & 9 Speed ATF Automatic Transmission Fluid or equivalent. Failure to use the correct fluid may Automatic Transmission — If Equipped affect the function or performance of your transmission. Manual Transmission —...

  • Page 300: Customer Assistance

    CUSTOMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE IF YOU NEED ASSISTANCE ROADSIDE ASSISTANCE Available 24 hours, 7 days a week. FOR YOUR VEHICLE FCA US LLC and its authorized dealers are vitally inter- Call 1-800-521-2779 or visit chrysler.rsahelp.com(USA) ested in your satisfaction. We want you to be happy with Call 1-800-363-4869 or visit fca.roadsideaid.com our products and services.

  • Page 301: Fca Us Llc Customer Center

    Phone: (877) 426-5337 patch a towing service to transport your vehicle to the P.O. Box 9145 closest authorized Chrysler, Dodge, Jeep®, or Ram CUSTOMER ASSISTANCE FOR THE Medford, MA 02155 dealer. If you choose to go to another dealer, you will be...

  • Page 302: Service Contract

    CUSTOMER ASSISTANCE SERVICE CONTRACT FCA US LLC is not responsible for any service contract MOPAR® PARTS you may have purchased from another manufacturer. If You may have purchased a service contract for a you require service after the FCA US LLC New Vehicle Mopar®...

  • Page 303: In Canada

    CUSTOMER ASSISTANCE ORDERING AND ACCESSING OWNER’S To contact NHTSA, you may call the To access your Owner's Information online, visit www.mopar.com/om (US) or www.owners.mopar.ca Vehicle Safety Hotline toll free at INFORMATION (Canada). 1-888-327-4236 (TTY: Or visit: 1-800-424-9153); or go to To order the following manuals, you may use either the www.techauthority.com to order physical copies of http://www.safercar.gov;...

  • Page 304: General Information

    CUSTOMER ASSISTANCE GENERAL INFORMATION The following regulatory statement applies to all Radio Frequency (RF) devices equipped in this vehicle: This device complies with Part 15 of the FCC Rules and with Innovation, Science and Economic Development Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: 1.
  • Page 305 INDEX Security Alarm ....20 Alterations/Modifications About Your Brakes....293 Battery .
  • Page 306 INDEX Car Washes ....288 Disposal Of Used Coolant ...259 Doors Removal, Front .
  • Page 307 INDEX Oil ....252, 296 Brake .....260 Oil Filler Cap .
  • Page 308 Security Alarm ....108 Jeep Wireless Speaker ... . .61, 64 4WD Part Time ....111 Service .
  • Page 309 INDEX Side Marker ....272 Mirrors ..... . .44 Synthetic .
  • Page 310 INDEX Replacement Keys ....17 Seat Belt Pretensioner ... . .205 Replacement Tires ....281 Untwisting Procedure .
  • Page 311 INDEX Oil ..... .296 To Open Hood ....91 Speed Control Tailgate .
  • Page 312 INDEX Tread Wear Indicators ....281 Wind Buffeting ....69 Turn Signals .
  • Page 315 ® Not all features shown in this manual may apply to your vehicle. For additional information, visit mopar.com/om (USA), owners.mopar.ca (Canada) or your local Jeep brand dealer. ®...
  • Page 316 Canada owners.mopar.ca ©2023 FCA US LLC. All Rights Reserved. Tous droits réservés. Jeep is a registered trademark of FCA US LLC. Jeep est une marque déposée de FCA US LLC. First Edition App Store is a registered trademark of Apple Inc. Google Play Store is a registered trademark of Google.

Table of Contents