Related Manuals for Teknik Craft 5421419
Summary of Contents for Teknik Craft 5421419
- Page 1 Teknik www.teknikoffice.co.uk Get crafty Craft Tower Craft Collection | Model 5421419 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
- Page 2 Table of Contents Assembly Tools Required Part Identifi cation No. 2 Phillips Screwdriver Tip Shown Actual Size Hardware Identifi cation Assembly Steps 5-28 Tape Measure Français 29-32 Español 33-36 Skip the power trip. Safety 37-38 This time. Warranty Page 2...
-
Page 3: Part Identification
Now you know Part Identifi cation our ABCs. å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identifi cation to help identify similar parts. LOWER RIGHT END (1) LOWER BACK (1) LONG BASE MOLDING (2) -
Page 4: Hardware Identification
Hardware Identifi cation å Screws are shown actual size. You may receive extra hardware with your unit. HIDDEN CAM - 28 CAM SCREW - 28 EXTENSION RAIL - 4 EXTENSION SLIDE - 4 (EXTENSION SET SHOWN SEPARATED) KNOB - 2 METAL PIN - 8 CAM COVER CARD - 5 WOOD DOWEL - 20... - Page 5 Step 1 Assemble your unit on a carpeted fl oor or on the empty å carton to avoid scratching your unit or the fl oor. Push twenty-eight HIDDEN CAMS (3) into the LOWER å ENDS (A and B), UPPER RIGHT END (D), UPPER BACK (F), LOWER BACK (I), CORK BOARD (J), SHORT BASE MOLDINGS (P) and DRAWER SIDES (R and T).
- Page 6 Step 2 Flip the UPPER BACK (F) over and place a SPACER (11) å over each hole. Place the PEGBOARD (E) onto the SPACERS (11). å Fasten the PEGBOARD (E) to the UPPER BACK (F). Turn six SILVER 1" PAN HEAD SCREWS (15) through six WASHERS (10), through the PEGBOARD (E), through six SPACERS (11) and into the UPPER BACK (F).
- Page 7 Step 3 Flip the CORK BOARD (J) over. å Just think. The sooner Turn four SILVER 1" PAN HEAD SCREWS (15) through å you do this, the sooner four WASHERS (10) and into the CORK BOARD (J). you do something else. SILVER 1"...
- Page 8 Step 4 Turn twenty-eight CAM SCREWS (4) into the LOWER å ENDS (A and B), TOP (C), UPPER BACK (F), LOWER SHELF (H), CORK BOARD (J), LONG BASE MOLDINGS (Q), and DRAWER FRONTS (V). NOTE: Use the exact holes shown. å...
- Page 9 Step 5 Insert two WOOD DOWELS (5) into the CORK BOARD (J). å Fasten the UPPER BRACE (L) to the CORK BOARD (J) by pushing the UPPER BRACE (L) onto the WOOD DOWELS. Fasten the UPPER RIGHT END (D) to the CORK BOARD (J). å...
- Page 10 Step 6 Insert two WOOD DOWELS (5) into the UPPER BRACE (L). å Fasten the UPPER BACK (F) to the UPPER RIGHT END (D). å Tighten two HIDDEN CAMS. NOTE: Be sure the WOOD DOWELS in the UPPER BRACE å insert into the holes in the UPPER BACK.
- Page 11 Step 7 Insert a WOOD DOWEL (5) into the holes in each edge of å the UPPER BACK (F) and CORK BOARD (J). Fasten the TOP (C) to the UPPER BACK (F) and CORK å BOARD (J). Tighten four HIDDEN CAMS. NOTE: Be sure the WOOD DOWELS in the UPPER BACK å...
- Page 12 Step 8 Carefully fl ip your unit over so the TOP (C) is on the fl oor. å Insert a WOOD DOWEL (5) into each edge of the UPPER å BACK (F) and CORK BOARD (J). Fasten the LOWER SHELF (H) to UPPER BACK (F) and å...
- Page 13 Step 9 Separate the EXTENSION SLIDES (2) from the EXTENSION RAILS (1) as shown in the upper diagram below. Be å prepared, the parts are greasy. Fasten the EXTENSION RAILS (1) to the LOWER ENDS (A and B). Use eight SILVER 1/2" FLAT HEAD SCREWS (18). å...
- Page 14 Step 10 Insert two WOOD DOWELS (5) into the LOWER RIGHT å END (A). Fasten the LOWER BRACE (K) to the LOWER RIGHT END (A) by pushing the LOWER BRACE (K) onto the WOOD DOWELS. Fasten the LOWER BACK (I) to the LOWER RIGHT END (A). å...
- Page 15 Step 11 Turn your unit onto its top edges while keeping the LOWER å BRACE (K) in place. Insert two WOOD DOWELS (5) into the LOWER BRACE (K). å Fasten the LOWER LEFT END (B) to the LOWER BACK (I). å...
- Page 16 Step 12 Insert a WOOD DOWEL (5) into each edge of the LOWER å ENDS (A and B). Side Step: Make nachos. (Optional, but Fasten the BOTTOM (M) to the LOWER ENDS (A and B). å recommended.) Use four SILVER 1-3/16" FLAT HEAD SCREWS (14). NOTE: Be sure the WOOD DOWELS in the LOWER ENDS å...
- Page 17 Step 13 Fasten eight METAL BRACKETS (9) to the BASE å MOLDINGS (P and Q). Use eight SILVER 1/2" PAN HEAD SCREWS (17). SILVER 1/2" FLAT HEAD SCREW Angled edge (8 used in this step) Slotted hole Angled edge Page 17...
- Page 18 Step 14 Insert four WOOD DOWELS (5) into the LONG BASE å MOLDINGS (Q). Fasten the SHORT BASE MOLDINGS (P) to the LONG å BASE MOLDINGS (Q). Tighten four HIDDEN CAMS. NOTE: Be sure the WOOD DOWELS in the LONG BASE å...
- Page 19 Step 15 Fasten the BASE MOLDINGS (P and Q) to the BOTTOM (M). å Use eight SILVER 1/2" PAN HEAD SCREWS (17). NOTE: You may need to loosen the screws in the METAL å BRACKETS so the BASE MOLDINGS (P and Q) cover the BOTTOM (M) edges.
- Page 20 Step 16 Fasten the TURNTABLE (12) to the TURNTABLE BOTTOM (N). å Use four SILVER 1/2" PAN HEAD SCREWS (17). Just breathe. It's going to be ok. SILVER 1/2" FLAT HEAD SCREW (4 used in this step) The large hole in the TURNTABLE (12) must line up with the large hole in the TURNTABLE...
- Page 21 Step 17 Flip the TURNTABLE (12) and TURNTABLE BOTTOM (N) over. å Place the TURNTABLE (12) on the BOTTOM (M), so the large hole in the TURNTABLE BOTTOM (N) lines up with the hole in å the TURNTABLE and the hole in the BOTTOM as shown below in diagram 1. Fasten the TURNTABLE to the BOTTOM with a SILVER 1/2"...
- Page 22 Step 18 Fasten the BASE (O) to the TURNTABLE BOTTOM (N). å Use four SILVER 1-7/8" FLAT HEAD SCREWS (13). SILVER 1-7/8" FLAT HEAD SCREW (4 used in this step) Unfi nished surface Page 22...
- Page 23 Step 19 Carefully stand your unit upright on the BASE (O). å Insert a WOOD DOWEL (5) into the hole in the edge of å each LOWER END (A and B). Fasten the LOWER SHELF (H) to the LOWER ENDS (A and B). å...
- Page 24 Step 20 SILVER 1-3/16" FLAT HEAD SCREW (8 used in this step) Groove Fasten the DRAWER SIDES (R and T) to the DRAWER BACK (S). Slide a DRAWER BOTTOM (U) into the grooves å å Use four SILVER 1-3/16" FLAT HEAD SCREWS (14). in the DRAWER SIDES (R and T) and DRAWER BACK (S).
- Page 25 Step 21 Fasten two EXTENSION SLIDES (2) to the å DRAWER SIDES (R and T). Use four SILVER 1/2" If you're doing this to FLAT HEAD SCREWS (18). help a friend, don't leave without a bite. Fasten the KNOB (6) to the DRAWER FRONT (V). Use a å...
- Page 26 Step 22 Fasten the LONG METAL SHELVES (X) to the UPPER å RIGHT END (D). Use nine SILVER 1/2" PAN HEAD SCREWS (17). Fasten the SHORT METAL SHELVES (W) to the LOWER å BACK (I). Use nine SILVER 1/2" PAN HEAD SCREWS (17). SILVER 1/2"...
- Page 27 Step 23 Push eight METAL PINS (8) into the UPPER BACK (F) and å CORK BOARD (J). Set the SHELVES (G) onto the METAL PINS (8). å To insert the drawers into your unit, line up the EXTENSION å SLIDES on the drawers with the EXTENSION RAILS on the unit and push the drawers into the unit until they are fully inserted.
- Page 28 Step 24 Peel a CAM COVER from the CAM COVER CARD (7) and å stick one onto each visible HIDDEN CAM. NOTE: Please read the back pages of the instruction å booklet for important safety information. This completes assembly. Clean with your favorite furniture å...