Related Manuals for Teknik Boulevard Cafe 5427345
Summary of Contents for Teknik Boulevard Cafe 5427345
- Page 1 Teknik www.teknikoffice.co.uk Get all organized and stuff. Lateral File NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Boulevard Cafe Collection | Model 5427345 PLEASE READ AND KEEP FOR FUTURE REFERENCE.
-
Page 2: Table Of Contents
Table of Contents Assembly Tools Required Part Identification No. 2 Phillips Screwdriver Hardware Identification Tip Shown Actual Size Hardware Usage Guide Assembly Steps 7-22 Hammer Not actual size Safety Page 2... -
Page 3: Part Identification
Now you know Part Identification our ABCs. å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts. TOP (1) DRAWER FRONT (2) LOWER FRONT BRACE (1) -
Page 4: Hardware Identification
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. (EXTENSION SET SHOWN SEPARATED) FRONT FILE EXTENSION RAIL - 4 EXTENSION SLIDE - 4 GLIDE - 2 LONG FILE SHORT FILE FILE GLIDE - 2 GLIDE - 4 HANGER - 4 LARGE WOOD... - Page 5 Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 1-3/4" HEX HEAD SCREW - 4 1-1/2" FLAT HEAD SCREW - 12 1-1/2" HEX HEAD SCREW - 8 9/16" PAN HEAD SCREW - 18 1/2"...
-
Page 6: Hardware Usage Guide
Hardware Usage Guide HOW TO USE A HIDDEN CAM & CAM SCREW OR CAM DOWEL NOTE: Various CAM SCREWS or a CAM DOWEL may be used. Turn the CAM SCREW or gently tap the CAM DOWEL until the shoulder is against the surface of the part. -
Page 7: Assembly Steps
Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Separate the EXTENSION SLIDES (2) from the EXTENSION RAILS (1) as shown in the upper diagram below. Be prepared, the parts are greasy. - Page 8 Step 2 å Fasten the BACK BRACES (N and Q) to the LEFT END (B). Tighten two 1-1/2" HEX HEAD SCREWS (18) Some assembly using the L-WRENCH (15). (and snacks) required. Edge with three tabs The EXTENSION RAILS are closer to this edge. Edge with four tabs Surface with holes 1-1/2"...
- Page 9 Step 3 å Fasten the FRONT BRACES (L and M) to the LEFT END (B). Tighten two 1-1/2" HEX HEAD SCREWS (18) using the L-WRENCH (15). The tabs face down and are closer to this surface. 1-1/2" HEX HEAD SCREW (2 used in this step) Page 9...
- Page 10 Step 4 å Fasten the RIGHT END (C) to the BRACES (L, M, N, and Q). Tighten four 1-1/2" HEX HEAD SCREWS (18) using the L-WRENCH (15). 1-1/2" HEX HEAD SCREW (4 used in this step) Page 10...
- Page 11 Step 5 å Connect the BACKS (D and E) together by inserting two LARGE WOOD DOWELS (9) into the holes in the BACKS (D and E) as shown. å Turn the HOOKS (11) into the BACKS (D and E) until they are snug.
- Page 12 Step 6 å Fasten the LOWER BACK BRACE (N) to the BACKS (D and E). Tighten four 1-3/4" HEX HEAD SCREWS (16) using the L-WRENCH (15). å NOTE: You should start each SCREW a few turns before completely tightening any of them. å...
- Page 13 Step 7 å Fasten the TOP (A) to the UPPER BRACES (M and Q). Use six 9/16" PAN HEAD SCREWS (19). å NOTE: You should start each SCREW a few turns before completely tightening any of them. 9/16" PAN HEAD SCREW (6 used in this step) h o l i t h...
- Page 14 Step 8 å Push ten HIDDEN CAMS (7) into the DRAWER SIDES (H and P) and DRAWER BRACES (K). Now might be a good time to refresh your drink. Arrow Page 14...
- Page 15 Step 9 å Insert four SMALL WOOD DOWELS (10) into the DRAWER BACK (G). å Fasten the DRAWER SIDES (H and P) to the DRAWER BACK (G). Use four 1-1/2" FLAT HEAD SCREWS (17). å Fasten the DRAWER BRACE (K) to the DRAWER BACK (G). Use two 1-1/2"...
- Page 16 Step 10 å Turn five CAM SCREWS (8) into the DRAWER FRONT (F). å Insert five SMALL WOOD DOWELS (10) into the DRAWER SIDES (H and P) and DRAWER BRACE (K). å Fasten the DRAWER FRONT (F) to the DRAWER SIDES (H and P) and DRAWER BRACE (K).
- Page 17 Step 11 å Fasten two EXTENSION SLIDES (2) to the DRAWER SIDES (H and P). Use six 3/8" FLAT HEAD SCREWS (22) in the exact holes shown. å Fasten one PULL (12) to the DRAWER FRONT (F). Use two 1/2" MACHINE SCREWS (20). å...
- Page 18 Step 12 å Fasten one FRONT FILE GLIDE (3) to the DRAWER FRONT (F). Use four 9/16" PAN HEAD SCREWS (19). å Press a LONG FILE GLIDE (4) onto the DRAWER BACK (G). å NOTE: The file tabs on the GLIDES should face each other. å...
- Page 19 Step 13 å Fasten the STRAPS (14) to the DRAWER BACK (G). From the back of the DRAWER, tighten two 3/8" HEX HEAD If you're doing this to SCREWS (21) through the STRAPS (14), through the help a friend, don't DRAWER BACK (G), and into the NUTS (23) using both leave without a bite.
- Page 20 Step 14 å Carefully stand your unit upright. å To insert the upper DRAWER with the STRAPS into your unit, line up the EXTENSION SLIDES on the drawer with the EXTENSION RAILS on the unit and push the drawer into the unit until the drawer is fully inserted. The drawer will push in hard until it is all the way in, then it will slide in and out easier.
- Page 21 Step 15 å To insert the lower DRAWER into your unit, line up the EXTENSION SLIDES on the drawer with the EXTENSION RAILS on the unit and push the drawer into the unit until the drawer is fully inserted. The drawer will push in hard until it is all the way in, then it will slide in and out easier.
- Page 22 Step 16 å Carefully stand your unit upright. å Peel APPLIQUES from the APPLIQUE CARDS (13) and stick them onto each visible HIDDEN CAM. å NOTE: Please read the back pages of the instruction booklet for important safety information. å This completes assembly.
-
Page 23: Safety
CAUTION Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded drawers. •...