Related Manuals for Teknik Craft 5421416
Summary of Contents for Teknik Craft 5421416
- Page 1 Teknik www.teknikoffice.co.uk Knick-knack paddywhack, give your stuff a home. Organizer Hutch Craft Collection | Model 421416 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
- Page 2 Table of Contents Assembly Tools Required Part Identifi cation No. 2 Phillips Screwdriver Tip Shown Actual Size Hardware Identifi cation Assembly Steps 5-19 Short Screwdriver Français 20-22 Español 23-25 Safety Skip the power trip. This time. Warranty Page 2...
- Page 3 Now you know Part Identifi cation our ABCs. å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identifi cation to help identify similar parts. RIGHT END (1) LEFT UPRIGHT (1) LEFT DRAWER SIDE (2)
-
Page 4: Table Of Contents
Hardware Identifi cation å Screws are shown actual size. You may receive extra hardware with your unit. LEFT EXTENSION RIGHT EXTENSION HIDDEN CAM - 26 CAM SCREW - 26 RAIL/SLIDE- 2 RAIL/SLIDE- 2 RIGHT CONNECTOR LEFT CONNECTOR KNOB - 2 CAM COVER CARD - 4 PLATE - 1 PLATE - 1... -
Page 5: Rail/Slide
Step 1 Assemble your unit on a carpeted fl oor or on the empty å carton to avoid scratching your unit or the fl oor. Fasten a RIGHT EXTENSION RAIL/SLIDE (2) to the å DIVIDER (H) as shown in the left diagram. Use two SILVER 1/2"... -
Page 6: Right Extension Rail/Slide
Step 2 Fasten the remaining LEFT EXTENSION RAIL/SLIDE (1) to å the LEFT END (B) as shown in the left diagram. Use two SILVER 1/2" FLAT HEAD SCREWS (12). Fasten the remaining RIGHT EXTENSION RAIL/SLIDE (2) å to the RIGHT END (A) as shown in the right diagram. Use two SILVER 1/2"... - Page 7 Step 3 Turn eight CAM SCREWS (4) into the ENDS (A and B). å (8 used) Page 7...
- Page 8 Step 4 Fasten the UPRIGHTS (F and G) to the SHELF (D). å Use four SILVER 1-3/16" FLAT HEAD SCREWS (9). NOTE: You should start each SCREW a few turns before å completely tightening any of them. Surface with holes Finished edge Surface with holes o l e...
-
Page 9: Hidden Cam
Step 5 Push two HIDDEN CAMS (3) into the DIVIDER (H). å Turn two CAM SCREWS (4) into the SHELF (D). å Fasten the DIVIDER (H) to the SHELF (D). Tighten two å HIDDEN CAMS. Arrow The arrow in the HIDDEN CAM must point toward the hole in the edge of the board. - Page 10 Step 6 Position the UPRIGHTS (F and G) as shown. å Fasten the BACK (E) to the UPRIGHTS (F and G) and å DIVIDER (H). Use three SILVER 1-3/16" FLAT HEAD SCREWS (9). NOTE: You should start each SCREW a few turns before å...
- Page 11 Step 7 Lay the unit on the BACK (E). å Push eight HIDDEN CAMS (3) into the SHELF (D) å and BACK (E). Fasten the ENDS (A and B) to the SHELF (D) and å Finished edge BACK (E). Tighten eight HIDDEN CAMS. Finished edge Arrow (8 used)
- Page 12 Step 8 Turn eight CAM SCREWS (4) into the TOP (C). å (8 used) Page 12...
- Page 13 Step 9 Push eight HIDDEN CAMS (3) into the ENDS (A and B) å and UPRIGHTS (F and G). Fasten the TOP (C) to the ENDS (A and B) and å UPRIGHTS (F and G). Tighten eight HIDDEN CAMS using your SHORT SCREWDRIVER. Back edges must be even.
- Page 14 Step 10 Turn eight CAM SCREWS (4) into the DRAWER å FRONTS (I and J). Fasten a KNOB (5) to each DRAWER FRONT (I and J). å Use two SILVER 11/16" MACHINE SCREWS (13). (8 used) SILVER 11/16" MACHINE SCREW (2 used in this step) Page 14...
- Page 15 Step 11 Fasten the DRAWER SIDES (K and L) to the DRAWER å BACKS (M). Use eight SILVER 1-3/16" FLAT HEAD SCREWS (9). SILVER 1-3/16" FLAT HEAD SCREW (8 used in this step) Groove Groove Page 15...
- Page 16 Step 12 Push eight HIDDEN CAMS (3) into the DRAWER å SIDES (K and L). Slide the DRAWER BOTTOMS (N) into the grooves in the å DRAWER SIDES (K and L) and DRAWER BACKS (M). Fasten the DRAWER FRONTS (I and J) to the DRAWER å...
- Page 17 Step 13 Carefully turn your unit onto its back edges. å Slide the DRAWERS between the ENDS (A and B) and å DIVIDER (H) as shown below. NOTE: Be sure the DRAWERS are positioned as å shown below. Fasten the EXTENSION RAILS/SLIDES (1 and 2) to the å...
- Page 18 Step 14 Carefully stand your unit upright. å Peel CAM COVERS from the CAM COVER CARDS (6) å and stick them onto the visible HIDDEN CAMS. 25 lbs. 20 lbs. total To cover HIDDEN CAMS 15 lbs. each Page 18 www.sauder.com 421416...
-
Page 19: Silver 13/16" Pan Head Screw
Step 15 This Hutch is designed to attach to the 421405 Open Storage å Cabinet and 421407 Storage Cabinet. Carefully set your Hutch on top of the unit you are å fastening it to. Fasten the CONNECTOR PLATES (7 and 8) to the Hutch å... - Page 20 WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves. •...