Related Manuals for Teknik Barrister Home 3 Drawer Chest 5418702
Summary of Contents for Teknik Barrister Home 3 Drawer Chest 5418702
- Page 1 Teknik www.teknikoffice.co.uk For things 'n such. Barrister Home 3 Drawer Chest Barrister Home Collection | Model 5418702 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
- Page 2 Table of Contents Assembly Tools Required Part Identifi cation No. 2 Phillips Screwdriver Tip Shown Actual Size Hardware Identifi cation Assembly Steps 5-18 Hammer Not actual size Français 19-21 Español 22-24 Short Screwdriver Safety 25-26 Tape Measure Warranty Skip the power trip. This time.
- Page 3 Now you know Part Identifi cation our ABCs. å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identifi cation to help identify similar parts. RIGHT END (1) BASE (1) LEFT MOLDING (1)
-
Page 4: Table Of Contents
Hardware Identifi cation å Screws are shown actual size. You may receive extra hardware with your unit. 10A SLIDE CAM - 6 35AA UNIVERSAL CABINET RAIL - 6 35AC DRAWER RIGHT - 3 35AD DRAWER LEFT - 3 MOLDING HIDDEN CAM - 15 CAM DOWEL - 15 METAL BRACKET - 7 CONNECTOR - 2... - Page 5 Step 1 Assemble your unit on a carpeted fl oor or on the empty å carton to avoid scratching your unit or the fl oor. Push fi fteen HIDDEN CAMS (1F) into the ENDS (A and B), å BOTTOM (D), BRACES (F), and DRAWER BRACES (M64). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM.
- Page 6 Step 2 Fasten the UNIVERSAL CABINET RAILS* (35AA) to the å ENDS (A and B). Use twelve GOLD 5/16" FLAT HEAD Remember: SCREWS (3S) through holes #1 and #3. Righty tighty. Lefty loosey. *patent pending glide system å GOLD 5/16" FLAT HEAD SCREW (12 used in this step) Glide end Finished edge...
- Page 7 Step 3 Tap two MOLDING CONNECTORS (19F) into the notches å in the MOLDINGS (K, N, and O). Use your hammer to tap the MOLDING CONNECTORS (19F) into the notches in the MOLDINGS. Flat end Unfi nished surface Unfi nished surface Flat end Unfi...
- Page 8 Step 4 Fasten the TOP (C) to the MOLDINGS (K, N, and O). Use å seven SILVER 1-1/8" FLAT HEAD SCREWS (10S). NOTE: Do not overtighten the SCREWS into the TOP. å SILVER 1-1/8" FLAT HEAD SCREW (7 used in this step) Do not overtighten the SCREWS (10S).
- Page 9 Step Step 5 Fasten the RIGHT END (A) to the RIGHT MOLDING (N). å Caution Tighten two HIDDEN CAMS. Do not stand the unit upright without the NOTE: The foam support needs to be at least 1-1/4" thick. å BACK fastened. The unit may collapse. f a c S u r w i t h...
-
Page 10: Hidden Cam
Step Step 6 Insert four METAL PINS (1R) into the ends of the BRACES (F). å Maximum Arrow Fasten the BRACES (F) to the RIGHT END (A). Tighten two å 210 degrees HIDDEN CAMS. NOTE: Be sure the METAL PINS in the BRACES insert into å... - Page 11 Step Step 7 Fasten the BOTTOM (D) to the RIGHT END (A). Tighten å two HIDDEN CAMS. Maximum Arrow 210 degrees Minimum If you're doing this to 190 degrees help a friend, don't leave without a bite. S u r f a c i t h H I D...
- Page 12 Step Step 8 Fasten the LEFT END (B) to the BOTTOM (D), BRACES (F), å and LEFT MOLDING (O). Tighten six HIDDEN CAMS. Maximum Arrow 210 degrees NOTE: Be sure the METAL PINS in the BRACES insert into å the holes in the LEFT END. Minimum NOTE: Use the Short Screwdriver for the HIDDEN CAMS in 190 degrees...
-
Page 13: Black 9/16" Large Head Screw
Step 9 Fasten seven METAL BRACKETS (4G) to the ENDS (A and B) and BOTTOM (D). Use seven BLACK 9/16" LARGE å HEAD SCREWS (1S). NOTE: Be sure the edges of the METAL BRACKETS are even with the edges of the ENDS and BOTTOM. å... - Page 14 Step 10 Unfold the BACK (E) and lay it over your unit. å Caution Make equal margins along all four edges of the BACK (E). å Do not stand the unit upright without the Push on opposite corners of your unit if needed to make BACK fastened.
-
Page 15: Black 1-9/16" Flat Head Screw
Step 11 With the palm of your hand, tap the The tabs should insert freely DRAWER BOTTOM down into the groove. into the slots. Gently tilt the DRAWER SIDES side to side until the tabs slip into the slots. fi n i s h r f a D994... -
Page 16: Gold 5/16" Flat Head Screw
Step 12 Insert a SLIDE CAM (10A) into the DRAWER SIDES (D26 and D27). å Fasten a DRAWER RIGHT (35AC) to the DRAWER RIGHT SIDE (D26) and a DRAWER LEFT (35AD) to the DRAWER LEFT å SIDE (D27). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #2. NOTE: The screw head in the CAM must be visible through the slotted hole in the SLIDE. - Page 17 Step 13 Carefully stand your unit upright. å Pro Tip: Lift with your To insert the drawers into your unit, tip the front of the drawer down å legs. And, you know, and drop the glides on the drawer behind the glides on the unit. Lift the your arms.
- Page 18 Step 14 To make adjustments to the drawers, loosen SCREW #2 in the SLIDES a 1/4 turn, then turn the CAM clockwise or å counter-clockwise. Notice how the drawer raises or lowers as you turn the CAM. The higher the screw in the oblong hole, the higher your drawer front will be.
- Page 19 WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded dresser drawers and •...