Related Manuals for Teknik White Home Study L-Shaped Desk
Summary of Contents for Teknik White Home Study L-Shaped Desk
- Page 1 Teknik Sit and surf. White Home Study L-Shaped Desk NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Model 5427718 PLEASE READ AND KEEP FOR FUTURE REFERENCE.
- Page 2 Table of Contents Assembly Tools Required Part Identification No. 2 Phillips Screwdriver Hardware Identification Tip Shown Actual Size Hardware Usage Guide Assembly Steps 7-42 Hammer Not actual size Français 43-47 Español 48-52 Safety 53-54 Warranty Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other.
- Page 3 Now you know Part Identification our ABCs. D109 D707 D708 Page 3...
- Page 4 Hardware Identification 45BA CABINET RIGHT - 1 45BB CABINET LEFT - 1 45BC DRAWER RIGHT - 1 45BD DRAWER LEFT - 1 (EXTENSION SET SHOWN SEPARATED) EXTENSION RAIL - 2 EXTENSION SLIDE - 2 45MA 45MC FILE GLIDE - 2 FILE ROD - 2 TWIST-LOCK ®...
- Page 5 Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 3S GOLD 5/16" FLAT HEAD SCREW - 16 BLACK 9/16" LARGE HEAD SCREW - 32 30S BLACK 1-9/16" FLAT HEAD SCREW - 8 SILVER 1-1/8" FLAT HEAD SCREW - 4 SILVER 1/2"...
- Page 6 Hardware Usage Guide HOW TO USE A TWIST-LOCK FASTENER ® Push a TWIST-LOCK® FASTENER 1. Insert the dowel end of the FASTENER into the into the large hole in the part. hole of the adjoining part. NOTE: The dowel end of the FASTENER must remain fully inserted in the hole of the adjoining part while locking the FASTENER.
- Page 7 Step 1 å NOTE: Two people are needed to build this unit. å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å To begin assembly, push two SAUDER TWIST-LOCK® FASTENERS (12F) into the large holes in the RIGHT END (A).
- Page 8 Step 2 å Push six HIDDEN CAMS (1F) into the RIGHT END (A). å Turn six CAM SCREWS (8F) into the LEGS (F and G). Arrow Arrow Page 8...
- Page 9 Step 3 å Insert two WOOD DOWELS (15F) into the LEGS (F and G). å Fasten the LEGS (F and G) to the RIGHT END (A). Tighten six HIDDEN CAMS. å NOTE: Be sure the WOOD DOWELS in the LEGS insert into the END.
- Page 10 Step 4 å Push six SAUDER TWIST-LOCK® FASTENERS (12F) into the large holes in the LARGE MODESTY PANEL (J). Do not tighten the TWIST-LOCK® FASTENERS in this step. Page 10...
- Page 11 Step 5 å Fasten the LARGE MODESTY PANEL (J) to the RIGHT END (A). Tighten three TWIST-LOCK® FASTENERS. For support, place packing foam and magazines here. Page 11...
- Page 12 Step 6 å Push two SAUDER TWIST-LOCK® FASTENERS (12F) into the large holes in the CORNER UPRIGHT (H). Do not tighten the TWIST-LOCK® FASTENERS in this step. Page 12...
- Page 13 Step 7 å Carefully turn the CORNER UPRIGHT (H) over. å Push six HIDDEN CAMS (1F) into the CORNER UPRIGHT (H). Arrow å Turn six CAM SCREWS (8F) into the LEGS (F and G). Arrow Page 13...
- Page 14 Step 8 å Insert two WOOD DOWELS (15F) into the LEGS (F and G). å Fasten the LEGS (F and G) to the CORNER UPRIGHT (H). Tighten six HIDDEN CAMS. å NOTE: Be sure the WOOD DOWELS in the LEGS insert into the UPRIGHT.
- Page 15 Step 9 å Fasten the CORNER UPRIGHT (H) to the LARGE MODESTY PANEL (J). Use four SILVER 1-1/8" FLAT HEAD SCREWS (10S). å NOTE: You should start each SCREW a few turns before completely tightening any of them. å NOTE: Do not overtighten the SCREWS into the UPRIGHT. SILVER 1-1/8"...
- Page 16 Step 10 å With someone's help, fasten the RIGHT END (A) and LARGE MODESTY PANEL (J ) to the SMALL TOP (C). Tighten four TWIST-LOCK® FASTENERS. å NOTE: Be sure the WOOD DOWEL in the END inserts into the TOP. Page 16...
- Page 17 Step 11 å Fasten the PLATES (41G) to the SMALL TOP (C). Use six BLACK 9/16" LARGE HEAD SCREWS (1S). BLACK 9/16" LARGE HEAD SCREW (6 used in this step) Page 17...
- Page 18 Step 12 å Fasten four ANGLE BRACKETS (5G) to the SMALL TOP (C). Use four BLACK 9/16" LARGE HEAD SCREWS (1S). å Fasten the LONG TOP MOLDING (P) to the ANGLE BRACKETS on the SMALL TOP (C). Use four BLACK 9/16" LARGE HEAD SCREWS (1S).
- Page 19 Step 13 å Insert two WOOD DOWELS (15F) into the LEFT END (B) and LEFT UPRIGHT (E). å Push four SAUDER TWIST-LOCK® FASTENERS (12F) into the large holes in the LEFT END (B) and LEFT UPRIGHT (E). Do not tighten the TWIST-LOCK® FASTENERS in this step. Page 19...
- Page 20 Step 14 å Push twelve HIDDEN CAMS (1F) into the LEFT END (B) and Arrow LEFT UPRIGHT (E). å Turn eighteen CAM SCREWS (8F) into the LEGS (F, G, S, and T). (12 used) Arrow (18 used) Page 20...
- Page 21 Step 15 å Insert two WOOD DOWELS (15F) into the LEGS (G and T). å Fasten the LEGS (G and T) to the LEFT UPRIGHT (E). Tighten six HIDDEN CAMS. å NOTE: Be sure the WOOD DOWELS in the LEGS insert into the UPRIGHT.
- Page 22 Step 16 å Insert two WOOD DOWELS (15F) into the LEGS (F and S). å Fasten the LEGS (F and S) to the LEFT END (B). Tighten six HIDDEN CAMS. å NOTE: Be sure the WOOD DOWELS in the LEGS insert into the END.
- Page 23 Step 17 å Separate the EXTENSION SLIDES (45MC) from the EXTENSION RAILS (45MA) as shown in the upper diagram below. Be prepared, the parts are greasy. å Fasten the EXTENSION RAILS (45MA) to the LEFT END (B) and LEFT UPRIGHT (E). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #4.
- Page 24 Step 18 å Fasten the CABINET RIGHT (45BA) to the LEFT UPRIGHT (E). Use two GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #4. å Fasten the CABINET LEFT (45BB) to the LEFT END (B). Use two GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #4.
- Page 25 Step 19 å Push two SAUDER TWIST-LOCK® FASTENERS (12F) into the large holes in the BACK (O). å Push six HIDDEN CAMS (1F) into the BACK (O). Do not tighten the TWIST-LOCK® FASTENERS in this step. Arrow Arrow Page 25...
- Page 26 Step 20 å Fasten the BACK (O) to the RIGHT REAR LEG (T). Tighten three HIDDEN CAMS. Edge with TWIST-LOCK® FASTENERS Page 26...
- Page 27 Step 21 å Push eight SAUDER TWIST-LOCK® FASTENERS (12F) into the large holes in the SHELF (L) and BOTTOM (M). Do not tighten the TWIST-LOCK® FASTENERS in this step. Page 27...
- Page 28 Step 22 å Slide the BOTTOM MOLDING* (R) onto the notched edge of the BOTTOM (M). å *U.S. Patent No. 5,499,886 Notched edge Slide the BOTTOM MOLDING (R) onto the notched edge. These surfaces should be even. The groove is closer to this edge.
- Page 29 Step 23 å Fasten the SHELF (L) and BOTTOM (M) to the LEFT UPRIGHT (E). Tighten four TWIST-LOCK® FASTENERS. Finished edge i t h ® f a c S u r - L O I S T E R S T E N F A S i t h...
- Page 30 Step 24 å Fasten the LEFT END (B) to the SHELF (L) and BOTTOM (M). Tighten four TWIST-LOCK® FASTENERS. å Fasten the LEFT REAR LEG (S) to the BACK (O). Tighten three HIDDEN CAMS. Page 30...
- Page 31 Step 25 å Fasten the LEFT END (B), LEFT UPRIGHT (E), and BACK (O) to the LARGE TOP (D). Tighten six TWIST-LOCK® FASTENERS. å NOTE: Be sure the WOOD DOWELS in the END and UPRIGHT insert into the TOP. These holes must be here. Page 31...
- Page 32 Step 26 å Push three SAUDER TWIST-LOCK® FASTENERS (12F) into the large holes in the SMALL MODESTY PANEL (K). Do not tighten the TWIST-LOCK® FASTENERS in this step. Page 32...
- Page 33 Step 27 å Fasten the SMALL MODESTY PANEL (K) to the LARGE TOP (D). Tighten three TWIST-LOCK® FASTENERS. å Fasten the SMALL MODESTY PANEL (K) to the LEFT UPRIGHT (E). Use three BLACK 1-15/16" FLAT HEAD SCREWS (113S). å NOTE: You should start each SCREW a few turns before completely tightening any of them.
- Page 34 Step 28 å Fasten three ANGLE BRACKETS (5G) to the LARGE TOP (D). Use three BLACK 9/16" LARGE HEAD SCREWS (1S). å Fasten the SHORT TOP MOLDING (Q) to the ANGLE BRACKETS on the LARGE TOP (D). Use three BLACK 9/16" LARGE HEAD SCREWS (1S).
- Page 35 Step 29 å With someone's help, carefully stand the assemblies upright near the unit's final location. å Fasten the LARGE TOP (D) to the CORNER UPRIGHT (H) and LARGE MODESTY PANEL (J). Tighten three TWIST-LOCK® FASTENERS. å Fasten the SMALL MODESTY PANEL (K) to the LARGE MODESTY PANEL (J). Use two BLACK 1-15/16"...
- Page 36 Step 30 å Pull the SMALL DRAWER FRONT BRACKETS (7G) apart and slide them into the grooves in the SMALL DRAWER SIDES (D53 and D59). You may need to gently tap them in with a hammer. å NOTE: The DRAWER FRONT BRACKETS are marked "RH" and "LH" for easy identification. å...
- Page 37 Step 31 å Fasten the DRAWER RIGHT (45BC) to the SMALL RIGHT DRAWER SIDE (D53). Use two GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #2 and #4. å Fasten the DRAWER LEFT (45BD) to the SMALL LEFT DRAWER SIDE (D59). Use two GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #2 and #4.
- Page 38 Step 32 å Pull the LARGE DRAWER FRONT BRACKETS (10G) apart and slide them into the grooves in the LARGE DRAWER SIDES (D32 and D33). You may need to gently tap them in with a hammer and screwdriver. å NOTE: The DRAWER FRONT BRACKETS are marked "RH" and "LH" for easy identification. You may need to use å...
- Page 39 Step 33 å Fasten the EXTENSION SLIDES (45MC) to the LARGE DRAWER SIDES (D32 and D33). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #2 and #4. å Fasten one KNOB (111K) to the LARGE DRAWER FRONT (U). Use one SILVER 1/2"...
- Page 40 Step 34 å Push a FILE GLIDE (5B) onto the LARGE RIGHT DRAWER SIDE (D33). å Slide the FILE RODS (8B) into the FILE GLIDE (5B) on the LARGE RIGHT DRAWER SIDE. å Slide another FILE GLIDE (5B) onto the other end of the FILE RODS (8B), then press this FILE GLIDE over the LARGE LEFT DRAWER SIDE (D32).
- Page 41 Step 35 å Insert the GROMMETS (10P) and GROMMET CAPS (1P) into the large holes in the TOPS (C and D). å To insert the SMALL DRAWER into your unit, tip the front of the drawer down and drop the rollers on the drawer behind the rollers on the unit.
- Page 42 Step 36 å Center a SCREW COVER (17P) over the head of each visible SCREW and gently tap in with your hammer. å Using your hammer, gently tap a CAM COVER (19P) onto each visible HIDDEN CAM. å NOTE: Please read the back pages of the instruction booklet for important safety information. å...
- Page 43 WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves or drawers. •...
- Page 44 ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Estantes o cajones sobrecargados. •...
- Page 45 5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the 4. This Warranty applies only to warranted defects that first arise and are reported to original purchaser of this product for a period of five years from the date of purchase Sauder within the warranty coverage period.
- Page 46 CONTACT US FIRST BEFORE MAKING ANY RETURNS TO THE RETAILER. So, how did it go? Dear Valued Customer: Thanks so much for choosing Sauder® furniture. I hope the Set a world record for speed? purchase and assembly process was a positive experience Feeling good about yourself? and you feel good about the furniture you just built.