Advertisement
Quick Links
Teknik
www.teknikoffice.co.uk
Storage Cupboard
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
Hudson Elm finish | Model 5427412
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-17
Français pg 18-20
Español pg 21-23
Lot # 566952
10/08/21
Purchased: __________________
Advertisement
Related Manuals for Teknik 5427412
Summary of Contents for Teknik 5427412
- Page 1 Teknik www.teknikoffice.co.uk Storage Cupboard NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Hudson Elm finish | Model 5427412 PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-17 Français pg 18-20 Español pg 21-23 Lot # 566952 10/08/21 Purchased: __________________...
- Page 2 Table of Contents Assembly Tools Required Hardware Identification No. 2 Phillips Screwdriver Part Identification Tip Shown Actual Size Hardware Usage Guide Assembly Steps 4-17 Hammer Not actual size Français 18-20 Español 21-23 Safety 24-26 Warranty Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. DOOR 13H HINGE - 4 WOOD DOWEL - 16...
- Page 3 Now you know Part Identification our ABCs. å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts. RIGHT END (1) BOTTOM (1) BACK (2)
- Page 4 Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Insert six WOOD DOWELS (42F) into the exact holes shown in the LEFT END (B). å NOTE: You may need to gently tap the WOOD DOWEL in with your hammer.
- Page 5 Hardware Usage Guide HOW TO USE A TWIST-LOCK FASTENER ® Push a TWIST-LOCK® FASTENER 1. Insert the dowel end of the FASTENER into the into the large hole in the part. hole of the adjoining part. NOTE: The dowel end of the FASTENER must remain fully inserted in the hole of the adjoining part while locking the FASTENER.
- Page 6 Step 3 å Fasten the BOTTOM (D) to the LEFT END (B). Tighten two TWIST-LOCK® FASTENERS. Just think. The sooner you do this, the sooner å NOTE: Be sure the WOOD DOWELS in the LEFT END you do something else. insert into the BOTTOM.
- Page 7 Step 4 å Insert six WOOD DOWELS (42F) into the exact holes shown in the RIGHT END (A). å NOTE: You may need to gently tap the WOOD DOWEL in with your hammer. Page 7...
- Page 8 Step 5 å Fasten the RIGHT END (A) to the BOTTOM (D) and BACKS (G). Tighten six TWIST-LOCK® FASTENERS. å NOTE: Be sure the WOOD DOWELS in the RIGHT END insert into the BACKS and BOTTOM. Page 8...
- Page 9 Step 6 å Using your hammer, gently tap four LEVELERS (46E) completely into the holes in the ENDS (A and B). å NOTE: Adjustments to the LEVELERS will be made later in assembly once your unit is standing upright. Page 9...
- Page 10 Step 7 å Fasten the BASE (E) to the ENDS (A and B) and the BOTTOM (D). Tighten four TWIST-LOCK® FASTENERS. Page 10...
- Page 11 Step 8 å Insert four WOOD DOWELS (42F) into the exact holes shown in the TOP (C). Now might be a good time to refresh å Insert the DOOR STOP (4I) into the exact holes shown in your drink. the TOP (C). Page 11...
- Page 12 Step 9 å Carefully stand your unit upright. å Fasten the TOP (C) to the ENDS (A and B). Tighten four TWIST-LOCK® FASTENERS. å Using your hammer, gently tap a TWIST-LOCK® FASTENER COVER (125P) onto each visible TWIST-LOCK® FASTENER. The DOOR STOPS must be here.
- Page 13 Step 10 å Fasten four HINGES (13H) to the DOORS (H). Use eight BLACK 1/2" FLAT HEAD SCREWS (11S). BLACK 1/2" FLAT HEAD SCREW (8 used in this step) Page 13...
- Page 14 Step 11 å Your unit may need leveling. To raise a corner of your unit, rotate the LEVELER downward. To lower a corner of your unit, rotate the LEVELER upward. Stop å Before fastening the DOOR to your unit, be sure the mounting screw is against the stops as shown in the right diagram.
- Page 15 Step 12 å Refer to the enlarged diagram to identify the parts on Mounting screw (depth) the HINGE. Adjusting screw (horizontal) å The DOOR may need some adjustments. Follow the text below to make needed adjustments. å DOOR ADJUSTMENTS: To adjust the DOOR from side to side (horizontal), turn the adjusting screw in or out.
- Page 16 Step 13 å Push the RUBBER SLEEVES (2R) over one end of the METAL PINS (1R). Insert the METAL PINS into the hole locations of your choice in the ENDS (A and B). Set the ADJUSTABLE SHELF (F) onto the METAL PINS. å...