EN
3.3 How the cooktop extractor works
Depending on the model you purchased, the cooktop extractor can be operated as an exhaust air or a recirculating
3.3 How the cooktop extractor works
3.3 How the cooktop extractor works
air version.
Depending on the model you purchased, the cooktop extractor can be operated as an exhaust air or a
recirculating air version.
Depending on the model you purchased, the cooktop extractor can be operated as an exhaust air or a recirculating
Exhaust air mode
air version.
Exhaust air mode
The air suctioned away is purified by the grease filter and expelled into the open air via a duct system. The exhaust
The air suctioned away is purified by the grease filter and expelled into the open air via a duct system.
Exhaust air mode
air must not be expelled into:
The exhaust air must not be expelled into:
a smoke or exhaust gas flue that is in operation
The air suctioned away is purified by the grease filter and expelled into the open air via a duct system. The exhaust
•
a smoke or exhaust gas flue that is in operation
a shaft used for the aeration of rooms where fireplaces are installed.
air must not be expelled into:
If the exhaust air is to be directed into a smoke or exhaust gas flue that is not in use, the installation must be
•
a shaft used for the aeration of rooms where fireplaces are installed.
a smoke or exhaust gas flue that is in operation
checked and approved by the responsible heating engineer.
If the exhaust air is to be directed into a smoke or exhaust gas flue that is not in use, the installation must
a shaft used for the aeration of rooms where fireplaces are installed.
be checked and approved by the responsible heating engineer.
Recirculation mode (only in C-version)
If the exhaust air is to be directed into a smoke or exhaust gas flue that is not in use, the installation must be
checked and approved by the responsible heating engineer.
Recirculation mode (only in C-version)
The air suctioned away is purified by the grease filter and an activated charcoal filter and fed back into the room in
The air suctioned away is purified by the grease filter and an activated charcoal filter and fed back into the
Recirculation mode (only in C-version)
which the appliance is installed. To prevent odours in recirculation mode, an odour filter must be used. For hygiene
room in which the appliance is installed. To prevent odours in recirculation mode, an odour filter must be
and health reasons, the activated charcoal filter must be replaced at the recommended intervals (see the Cleaning
used. For hygiene and health reasons, the activated charcoal filter must be replaced at the recommended
and maintenance chapter).
The air suctioned away is purified by the grease filter and an activated charcoal filter and fed back into the room in
intervals (see the Cleaning and maintenance chapter).
which the appliance is installed. To prevent odours in recirculation mode, an odour filter must be used. For hygiene
and health reasons, the activated charcoal filter must be replaced at the recommended intervals (see the Cleaning
3.4 How the induction cooktop works
and maintenance chapter).
How the induction cooktop works
3.4.1 Slide control
3.4.1 Slide control
3.4 How the induction cooktop works
The glass ceramic hob is operated with touch control sensor keys. The sensor keys are operated as
The glass ceramic hob is operated with touch control sensor keys. The sensor keys are operated as follows: lightly
follows: lightly touch a symbol on the surface of the ceramic glass plate. A buzzer will indicate when the
3.4.1 Slide control
touch a symbol on the surface of the ceramic glass plate. A buzzer will indicate when the controls have been
controls have been operated correctly.
operated correctly.
The touch control sensor key will then be indicated as "key".
The glass ceramic hob is operated with touch control sensor keys. The sensor keys are operated as follows: lightly
The touch control sensor key will then be indicated as "key".
What must be observed when operating sensor fields?
touch a symbol on the surface of the ceramic glass plate. A buzzer will indicate when the controls have been
Your finger should not be placed flat onto the glass ceramic surface in order to avoid adjacent keys/sensor
What must be observed when operating sensor fields?
operated correctly.
fields from reacting by mistake.
Your finger should not be placed flat onto the glass ceramic surface in order to avoid adjacent keys/sensor fields
The touch control sensor key will then be indicated as "key".
from reacting by mistake.
What must be observed when operating sensor fields?
Your finger should not be placed flat onto the glass ceramic surface in order to avoid adjacent keys/sensor fields
from reacting by mistake.
Press the sensor field lightly or move your finger around
Press the sensor field lightly or move your finger around
You can press the sensor field very lightly with your finger; when this is done the setting on the display
You can press the sensor field very lightly with your finger; when this is done the setting on the display (power
(power level) will gradually change.
level) will gradually change.
Press the sensor field lightly or move your finger around
When you put your finger on the sensor field and then move it to the left or right, the display setting will
When you put your finger on the sensor field and then move it to the left or right, the display setting will change
You can press the sensor field very lightly with your finger; when this is done the setting on the display (power
progressively.
change progressively.
level) will gradually change.
The faster the movement, the faster the change in the display.
The faster the movement, the faster the change in the display
When you put your finger on the sensor field and then move it to the left or right, the display setting will change
progressively.
The faster the movement, the faster the change in the display.
48
APPLIANCE DESCRIPTION
APPLIANCE DESCRIPTION
unsuitable
WARNING OF ELECTRICAL ENERGY!
RISK OF FATAL INJURY!
unsuitable
Live components have been installed near this
symbol. Covers bearing this sign may only be
removed by a certified skilled electrician.
CAUTION! HOT SURFACES!
This symbol has been applied to surfaces which get
hot. There is a risk of serious burning or scalding.
The surfaces may also be hot after the appliance has
been switched off.
touch
OBSERVE
ELECTROSTATICALLY
1
2 3 4 5 6 7 8 9 P
COMPONENTS AND MODULES (ESDS)
touch
Electrostatically
modules are located behind covers bearing the
1
2 3 4 5 6 7 8 9 P
adjacent symbol. Never touch plug connections, strip
conductors or component pins. Only qualified staff
members who are familiar with ESDs are authorised
to carry out any technical intervention work.
right
right
move
REGULATIONS
FOR
1 2 3 4 5 6 7 8 9 P
move
endangered
1 2 3 4 5 6 7 8 9 P
6
6
EN
HANDLING
SENSITIVE
5
Cleaning an
components
and
Switch the hob
Never clean the
When cleaning
accidentally swi
EN
Need help?
Do you have a question about the NIVEL PRO and is the answer not in the manual?