Important Safety Information - Hatco CSU Series Installation And Operating Manual

English
Read the following important safety information before using this equipment to avoid serious
injury or death and to avoid damage to equipment or property.
WARNING
ELECTRIC SHOCK HAZARD:
• Plug unit into a properly grounded electrical receptacle
of the correct voltage, size, and plug configuration. If
plug and receptacle do not match, contact a qualified
electrician to determine and install proper voltage and
size electrical receptacle.
• Turn OFF power switch and unplug power cord before
performing any cleaning, adjustments, or maintenance.
• Unit is not weatherproof. Locate unit indoors.
• Control enclosure must be mounted in a vertical
surface. Mounting control enclosure in a horizontal
surface may result in the collection of liquids and lead
to electric shock.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• This unit is not "jet-proof" construction. Do not use
jet-clean spray to clean this unit.
• Do not steam clean or use excessive water on unit.
• Discontinue use if power cord is frayed or worn.
• Do not attempt to repair or replace a damaged power
cord. Cord must be replaced by an Authorized Hatco
Service Agent or a person with similar qualifications.
• This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to electric
shock or burn.
• Use only Genuine Hatco Replacement Parts when
service is required. Failure to use Genuine Hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them to
operate safely in Hatco equipment.
FIRE HAZARD:
• Install condensing unit with a minimum of 51 mm (2")
of space between all sides of unit and any combustible
surfaces.
• Do not use flammable cleaning solutions to clean this
unit.
EXPLOSION HAZARD: Do not store or use gasoline or
other flammable vapors or liquids in the vicinity of this or
any other appliance.
Make sure food product and food pans have been chilled
to the proper food-safe temperature before placing on
unit. Failure to chill food product properly may result in
serious health risks. This unit is for holding pre-chilled
food product only.
This unit is for holding food for short periods of time.
Never hold food longer than 4 hours.
Hatco Corporation is not responsible for actual food
product serving temperature. It is the responsibility of the
user to ensure that food product is held and served at a
safe temperature.
Form No. CS_AAM-0417

IMPORTANT SAFETY INFORMATION

Maintain proper cleanliness of unit. Proper cleanliness and
sanitation is critical for food-safe operation. Refer to the
MAINTENANCE section for cleaning procedures.
Do not place food product directly onto hardcoat surface.
Food product must be wrapped, boxed, or on a food pan.
This unit is not intended for use by children or persons
with reduced physical, sensory, or mental capabilities.
Ensure proper supervision of children and keep them
away from the unit.
Make sure all operators have been instructed on the safe
and proper use of the unit.
This unit has no "user-serviceable" parts. If service
is required on this unit, contact an Authorized Hatco
Service Agent or contact the Hatco Service Department at
414-671-6350.
Locate the unit at proper counter height in an area that is
convenient for use. The location should be level and strong
enough to support the weight of the unit and contents.
DO NOT tip unit/mounting surface after final installation.
Unit is free-floating and could fall out if tipped—for
permanent, horizontal installations only.
Make sure to clean and sanitize stone surface properly
after deep cleaning the surface using abrasives and before
placing food product on unit.
This unit is designed for use in environments where
ambient temperature is between 18°C (65°F) and 30°C
(86°F).
When shipped during cold weather months, store unit
for at least 10 hours in an environment where ambient
temperature is between 18°C (65°F) and 30°C (86°F) to
prevent compressor and/or refrigerant line damage. If unit
is turned on and there is excessive noise and vibration,
turn off immediately and allow additional warmup time.
Provide louvered or grill-style openings with a
minimum size of 31 x 31 cm/961 square cm (12" x 12"/
144 square inches) in the cabinetry in front of and behind
the condensing unit for proper ventilation. Failure to
provide adequate air flow through the condensing unit
may cause unit failure and will void the unit warranty.
Do not recirculate exhaust air inside cabinet when multiple
condensing units are installed together. Intake air should
enter from outside of cabinet.
Transport and install unit in upright position only. Failure
to do so may result in damage to the refrigeration system.
Use caution and avoid hitting condensing unit hoses/lines
when installing unit. Damage caused during installation is
not covered under warranty.
3
WARNING
CAUTION
NOTICE