Integrated Furnace Control Menu - Trane S8V2A040M3PC Installation, Operation And Maintenance Manual

Integrated Furnace Control Menu

IdL
Status menu
ORN
Unit Orienta on
Err
Ac ve Errors
L6F
Last 6 Faults
CR
Control Release #
mrn
Model Number
Recovery
COd
Cooling Off Delay
ODE
Outdoor Tonnage
ODU
OD Unit Type
COF
Con nuous Fan
CPC
Cooling CFM per Ton
CPH
Hea ng CFM per Ton
HOD
Heat Off Delay
ISD
Inter-Stage Delay
9HC
Gas Hea ng CFM
rat
Return Air Temp
Sat
Supply Air Temp
RSP
Return Sta c
Pressure
RUN
Run Test Mode
S8V2-SVX001-1A-EN
24V Control System Menu
Example Example
st
1 stage Gas Heat 800 CFM
Ht1 ARF
DN
UP
R9T
E3.4 E3.1
Example
Example
st
nd
1 Stage Pressure Switch Error
2 Stage Pressure Switch Error
E3.4 E3.1
Example
So ware Version #
021
Example
Example
S8V2A040M3 S8V2B060M4
001
000
Example
seconds
090
000
Example
Outdoor Nominal Tonnage
1.5
3_0
Example Example
1 stage 1 compressor 2 stage 1 compressor 2 stage 2 compressor
2-1
1-1
Example
50% Cooling Airflow
50 75
Example
CFM per Ton
370
350
Example
CFM per Ton
370
350
Example
seconds
100
140
Example
seconds
600 900
Example
nd
2 stage Hea ng CFM
105 120
d15
ena
ena
D1A
ena D1A
See Run Test Menu
S8V2-C
080
LFT AUT
Example
Open Limit Switch Error
E04
Example
S8V2B080M4
002
Example
Enhanced Mode
180 EH
2.0 2.5
Example
2-2
100 25
400
400
180
60
300
000
140 090
SETTING UP YOUR SYSTEM:
To change any factory default value, first remove and "call"
from the furnace and allow any fan off delays to finish. ( 1 DL
should be seen on the display)
Scroll to the selected Menu item by momentarily depressing
the "MENU" key and then depress the "OPTION" key to the
desired se ng. Then momentarily depress the "MENU" key
again to save the change.
CLEARING THE LAST 6 FAULTS:
To clear the stored faults, scroll to the last 6 faults menu (LF6),
enter the menu by scrolling to the right and hold the
"OPTION" key for at least 5 seconds. Release and a set of 3
dashes will be seen 3 mes. This confirms the faults have
been cleared.
Model Number
Model Number
Recovery Digit
S8V2A040M3PC 1
S8V2B060M4PC 2
S8V2B080M4PC
3
S8V2C080M5PC 4
S8V2C100M5PC 5
S8V2D120M5PC 6
S8V2A040M3PD
7
S8V2B060M4PD 8
S8V2B080M4PD 9
S8V2C080M5PD 10
S8V2C100M5PD
11
S8V2D120M5PD 12
Model Number ODT Op ons [ ] = Default
S8V2A040M3PC/D [3T], 1.5T, 2T, 2.5T
S8V2B060M4PC/D [4T], 1.5T, 2T, 2.5T, 3T, 3.5T
S8V2B080M4PC/D [4T], 2T, 2.5T, 3T, 3.5T
S8V2C080M5PC/D [5T], 2.5T, 3T, 3.5T, 4T, 4.5T
S8V2C100M5PC/D [5T], 2.5T, 3T, 3.5T, 4T, 4.5T
S8V2D120M5PC/D [5T], 3T, 3.5T, 4T, 4.5T
NOTE:
Do not adjust COF above 75%.
CFM per Ton selec ons range from 290 - 450.
Important:
When applied with zoning or a VSPD outdoor unit,
the CFM/Ton must be set to 400.
nd st
Gas hea ng CFM shown is 2 stage airflow. 1 stage airflow is
nd
~80% of the selected 2 stage airflow and cannot be adjusted.
NOTE: Using the link mobile app, (Gas Hea ng Test) is
recommended for se ng airflow and adjus ng gas manifold
pressure.
the value shown by 10 for actual airflow.
Se ng airflow "On the Fly" is not available on this control.
Model Number Gas Hea ng CFM [ ] = Default
S8V2A040M3PC/D 064[064], 075, 085, 054
S8V2B060M4PC/D 105[105], 120, 140, 090
S8V2B080M4PC/D 133[133], 147, 160, 106
S8V2C080M5PC/D 135[135], 145, 165, 115
S8V2C100M5PC/D 165[165], 180, 136, 150
S8V2D120M5PC/D 174[174], 185, 200, 150
53