Table of Contents
Advertisement
Opening
and closing
Programming or reprogramming buttons
.. Switch t he ignition on .
.. Press and hold the but ton in t he roof headliner
¢
page
39,
fig.
34 that you would like to pro-
gram fo r at least 10 seconds. Or
.. Select :
I CARI
funct ion button> Car systems*
contro l button
>
Vehicle settings > Garage
door opener > Program garage door opener.
If
th is path is not availab le, program t he button
as describ ed in vers ion B
¢
page
39 .
.. Follow t he ins tr uct ions in t he MMI.
Erasing button programming
The programmed buttons cannot be erased indi-
vid ually. They must all be erased toget her . Re-
p rogram the but t ons if necessary .
.. Select:
IC ARI
funct ion button> Car systems*
contro l button > Vehicle settings > Garage
door opener > Clear program settings > Yes.
Displaying the version/status/country
code
.. Se lect:
ICARI
funct io n button > Car systems*
contro l button > Vehicle settings > Garage
door opener > Version information .
@
Tips
- Programming th rough the MMI* is not pos-
s ible wit h all infotainment systems. If this
is the case, program the buttons as descri -
bed in version B
¢
page
39.
- The requir ed distance between the ha nd
transmitter
and the Homelink mod ule in
the radiato r gri lle ¢
page
40,
fig.
35 de-
pends o n the system that you a re prog ram-
ming.
- Depend ing on th e model of the system, you
may need t o re leas e the butt o n on the re-
mote con tr ol dur ing progra mmin g an d
press it again . Ho ld ea ch posi tion you tr y for
at least 15 second s before t rying ano th er
position . Keep t he t ur n sig na ls on your vehi -
cle in view when do ing t his.
- Aft er progra m ming th e g arag e door ope ner,
it may be necessary to synchronize the mo -
tor with the system . Refer to the ma nuf ac-
turer's instructions.
40
Programming the buttons (version B)
Applies to : vehicles with garage door opener (Horne link)
Fig. 35
Dista nce between the radiator g rille and th e hand
transmitter
Programming the button: Part
1
with the
controls
1.
Switc h the ign ition on .
2 . Press and hold both outer buttons in t he roof
headline r ¢
page
39,
fig.
34 unt il the LED®
turns off complete ly (after about 20 sec-
onds). This procedure clears the standard co-
des that were set at the facto ry and does not
need t o be repea t ed again t o prog ram the
othe r but tons .
3. Briefly press t he but ton on t he roof head liner
t hat you wo uld like to pr ogra m.
4 . Wai t until th e LED@ be gins t o blink qu ickly.
Programming mode is active for 5 minutes.
5 . Move in front of your veh icle while holding
t he or igina l remote cont rol for the system
t hat wou ld like to program to a button in the
roof headliner.
Programming the button: Part 2 at the
radiator grille
6. Hold the remote control up to t he radiator
grille on your vehicle
¢fig.
35.
7. Press and hold the remote control unt il the
tu rn signals on your veh icle blink . This may
t ake up to 30 seconds .
8 . If t he eme rge ncy fl ashers b link t hree ti m es,
t he progr a mm ing was s uccessfu l. If t he
emergency fl as hers only blink one t ime, t he
5 m inute time limit for the prog ramming has
ended or the prog ramming was not success-
ful. Repeat the prog ramming from t he third
step, or try chang ing the distance to the radi-
ator g rille.
..,_
Advertisement
Table of Contents
